xpr B100-SA Standalone Biometric Reader
Tlhahisoleseding ya Sehlahiswa
- Lebitso la Sehlahiswa: B100-SA v2
- Mofuta: Sebali se ikemetseng sa Biometric
- Moetsi: Sehlopha sa XPR
- Websebaka: www.xprgroup.com.
- Tlhatlhobo: 1.01 - 31.03.2022
Selelekela
B100-SA v2 ke sebali sa biometric se ikemetseng se fanang ka taolo e sireletsehileng ea phihlello. E etselitsoe ho skena likhatiso tsa menoana le ho fana ka phihlello ho ipapisitsoe le menoana e lumelletsoeng e ngolisitsoeng tsamaisong. Bukana ea ho kenya mochine ona e fana ka litaelo tse qaqileng mabapi le ho kenya, ho kenya marang-rang, ho etsa mananeo, le tšebeliso ea B100-SA v2.
Ho phahamisa
Buka ea mosebelisi ha e fane ka litaelo tse tobileng tsa ho kenya. Ka kopo, sheba litataiso tsa moetsi kapa u buisane le motho ea nang le tumello bakeng sa ho kenya B100-SA v2 hantle.
Litlhaloso
- Bokhoni ba Menoana: [lintlha ha li fanoe]
- Sephetho: [lintlha ha li fanoe]
- Kenyo ea Konopo: [lintlha ha li fanoe]
- Khokahano ea Panel: [lintlha ha li fanoe]
- Nako ea ho Bula Monyako: [lintlha ha li fanoe]
- Mokhoa oa ho Kena: [lintlha ha li fanoe]
- Lenaneo: [lintlha ha li fanoe]
- Menoana ea Mookameli/ ea Seseho: [lintlha ha li fanoe]
- Lebone la Morao-rao le ON/Timme: [lintlha ha li fanoe]
- Buzzer ON/OFF: [lintlha ha li fanoe]
- Ntlafatsa Firmware: [lintlha ha li fanoe]
- Tšebeliso ea Hona Joale: [lintlha ha li fanoe]
- Phepelo ea motlakase: [lintlha ha li fanoe]
- Sesupo: [lintlha ha li fanoe]
- IP Factor: [lintlha ha li fanoe]
- Thempereichara ea ho sebetsa: [lintlha ha li fanoe]
- Mongobo o sebetsang: [lintlha ha li fanoe]
- Boholo(mm): [lintlha ha li fanoe]
Setšoantšo sa Kopo
Buka ea mosebelisi ha e fane ka setšoantšo sa ts'ebeliso. Ka kopo, sheba litataiso tsa moetsi kapa u buisane le motho ea nang le tumello bakeng sa tšebeliso e nepahetseng ea B100-SA v2.
Mokhoa o khothaletsoang oa Swiping
Ho etsa bonnete ba hore ho na le sesupa se nepahetseng sa menoana, latela litaelo tsena:
- Qala ho tloha monoana oa pele oa monoana.
- Beha monoana o khethiloeng ho sensor ea swipe.
- Tsamaisa monoana ka ho lekana ho ea ho uena ka motsamao o le mong o tsitsitseng.
Sephetho:
- Bakeng sa swipe e nepahetseng: Tricolor Status LED e fetoha e tala + OK Beep (mokhutšoane + o molelele oa beep).
- Bakeng sa swipe e fosahetseng kapa e sa baleheng hantle: Tricolor Status LED e fetoha khubelu + Error Beep (3 li-beep tse khutšoane).
Pontsho
Buka ea mosebedisi ha e fane ka lintlha tse tobileng mabapi le pontšo. Ka kopo, sheba litataiso tsa moetsi kapa u buisane le motho ea nang le tumello bakeng sa kutloisiso e nepahetseng ea sesupo sa B100-SA v2.
Wiring
Buka ea mosebedisi ha e fane ka litaelo tse tobileng tsa wiring. Ka kopo, sheba litataiso tsa moetsi kapa u buisane le motho ea nang le tumello bakeng sa ho kenya likhoele tse nepahetseng tsa B100-SA v2.
Ho eketsa Monoana oa Tsamaiso
- Push dip switch no.2 boemong ba HO BUA.
- Seta hape matla a sesebelisoa.
- Emela ho bepi e le 'ngoe e telele + e mengata e khutšoanyane.
- Beha switjha ea ho qoelisa sebakeng HO TLOA (li-beeps tse khutšoane li tla emisa).
- Ema metsotsoana e ka bang 15 hore LED e benye ka Orange.
- Swaepa Monwana wa Monghadi min. 6 linako (Ho fihlela OK Beep).
LIEKETSENG
B100-SA v2 ke sebali sa menoana sa taolo ea phihlello se etselitsoeng taolo e bonolo ea basebelisi le tlhophiso. Scanner e entsoe ka theknoloji e tsoetseng pele ea capacitive sensing e fanang ka advan e itsengtage fetang tharollo ea optical joalo ka:
- ho etsa hoo e ka bang ha ho khonehe ho etsa kopi ea fake ea menoana ea basebelisi
- tshebetso e tshwanang maemong a kganya a fapaneng
- ho bala hantle menoana e nang le matheba a mesebetsi ea letsatsi le letsatsi
E hahelletsoeng ka har'a skena e matla le algorithm e ts'oanang e fana ka mamello e ntle haholo ka tsela eo menoana e ts'oaroang ka eona holim'a sensor e fokotsang tlhoko ea ho pheta-pheta ho swipe ka menoana ho sensor. 'Mali a ka boloka litempele tse fihlang ho 100 tsa menoana. Thempleite e le 'ngoe e boloketsoe Mookameli oa Mosebelisi (Motsamaisi), thempleite e le 'ngoe e boloketsoe tlhophiso ea Reader (Installer) 'me litempele tse fihlang ho 98 ke tsa Basebelisi.
KHOTHATSO
Buisana le installer mabapi le boemo ba polokeho ea instola. Ho na le lisebelisoa tse nang le li-relay tse tsamaellanang le 'mali enoa tse ka eketsang ts'ireletso ea sistimi ha ho hlokahala. Monoana o le mong kapa tse peli tse ngolisitsoeng li lekane mosebelisi a le mong. Botsa motho ea kenyang sebaka pele a tloha sebakeng sena ho ngolisa monoana oa hau e le mookameli.
LINTLHA TSEO: 'Mali o sebelisa ho khopama ha mongolo oa menoana ho hlahloba monoana. Basebelisi ba bang ba kanna ba ba le menoana e bataletseng haholo, e leng ho etsang hore ho be thata ho sensor ho lemoha menoana ka nepo. Hangata, bana ke bana le batho ba baholo. Ho rarolla bothata bona, etsa se latelang:
- Leka ka menoana e fapaneng ea basebelisi ho fumana monoana o "molemo ka ho fetisisa".
- Sheba le sehokelo bakeng sa mefuta e meng ea 'mali ka sebali sa karete se ekelitsoeng kapa letlapa la likonopo bakeng sa mofuta o mong oa phihlello.
TLHOKOMELO
Ha ho hlokahale tlhokomelo e khethehileng kapa nako le nako. Haeba ho hlokahala ho hloekisa, sebelisa lesela le bonolo le metsi 'me u hlakole litšila ka bonolo. U se ke ua sebelisa lik'hemik'hale le lisebelisoa tse ka senyang sensor
TEMOSO! Se ke oa ama sensor ka lintho tse ling ntle le monoana oa hau. U se ke ua tšela kapa ua fafatsa ka metsi kapa maro a mang. Ha mosebetsi oa ho penta kapa oa kaho o ntse o tsoela pele sebakeng se potolohileng 'mali, sireletsa sebaka sa sensor ea 'mali ho tloha tšenyo e ka bang teng le pente. Haeba 'mali a lokela ho theoloa kapa a fallisoe sebakeng se seng, letsetsa motho ea lumelletsoeng bakeng sa mosebetsi oo. Ho lahloa ha sehlahisoa sena ho tlameha ho sebetsoa ho latela melao le melaoana eohle ea naha.
KHABANE
- Se ke oa kenya sesebelisoa le cabling haufi le mohloli oa libaka tse matla tsa makenete ea motlakase joalo ka lenakana le fetisang radio.
- Se ke oa beha sesebelisoa haufi kapa ka holim'a thepa ea ho futhumatsa.
- Haeba u hloekisa, u se ke ua fafatsa kapa ua fafatsa metsi kapa lino tse ling tse hloekisang empa u li hlakole ka lesela le boreleli kapa thaole.
- U se ke ua lumella bana ho tšoara sesebelisoa ntle le tlhokomelo.
- Hlokomela hore ha sensor e hloekisoa ka sesepa, benzene kapa thinner, bokaholimo bo tla senyeha 'me menoana e ke ke ea kenngoa.
- Mocheso o sebetsang oa sehlahisoa o pakeng tsa 0ºC - + 50ºC. XPR™ e ke ke ea tiisa tšebetso ea sehlahisoa haeba mehato le likeletso pele li sa lateloe.
LIEKETSENG TS'OANELO
- Bokhoni ba Menoana: 98 litempele
- Sephetho: 1 x Relay (2 A /24V AC/DC)
- Kenyo ea Konopo: Ee
- Khokahano ea Panel: Cable, 0.5 m
- Nako ea ho Bula Monyako: Pulse (metsotsoana e 1 ho isa ho e 30) kapa Toggle (ON/OFF)
- Mokhoa oa ho Kena: Monoana
- Lenaneo: Ka ho swiping
- Menoana ea Mookameli/ ea Seseho: 1 Taolo le Monoana o le Mong oa Sehokelo
- Lebone la Morao-rao le ON/Timme: Ee
- Buzzer ON/OFF: Ee
- Ntlafatsa Firmware: ka RS-485 converter le Windows application
- Tšebeliso ea Hona Joale: 100 mA max.
- Phepelo ea motlakase: 9-14V DC
- Sesupo: Boemo ba Tricolor LED
- IP Factor: IP54 (tšebeliso ea ka hare feela)
- Thempereichara ea ho sebetsa: 0°C ho ea ho +50°C
- Mongobo o sebetsang: 5% ho isa ho 95% RH ntle le condensation
- Boholo(mm): 92 x 51 x 25 (tšepe); 92 x 51 x 27 (ABS)
TS'ELISO TS'OANELO
RETŠELISITSOE MOKHOA
Latela litaelo tse ka tlase bakeng sa ho sututsa menoana ka nepo. Ho qala ka lenonyeletso la monoana oa pele, beha monoana o khethiloeng holim'a sensor ea swipe 'me u e tsamaise ka ho lekana ho uena ka motsamao o le mong o tsitsitseng.
Sephetho:
- Bakeng sa swipe e nepahetseng: Tricolor Status LED e fetoha e tala + OK Beep (mokhutšoane + o molelele oa beep)
- Bakeng sa swipe e fosahetseng kapa e sa baloeng hantle: Tricolor Status LED e fetoha bofubelu + Beep ea Phoso (li-beep tse 3 tse khutšoane)
TS'ELISO
- OK Beep - mololi o mokhutšoane + o molelele
- Phoso ea Beep – 3 melumo e khutšoanyane
- Swipe Monwana - 2 li-beep tse khutšoane
KHOPO
KEKELETSO MONOANA
- Push dip switch no.2 boemong ba HO BUA.
- Seta bocha Matla a sesebelisoa.
- Emela ho bepi e le 'ngoe e telele + e mengata e khutšoanyane
- Beha switjha ea ho qoelisa sebakeng HO TLOA. (li-beeps tse khutšoane li tla emisa)
- Ema metsotsoana e ka bang 15 hore LED e benye ka Orange.
- Swipe Monoana oa Monghali min.6 linako tse ling. (Ho fihlela Ok Beep)
- Tlhokomediso: Mokhoa ona o boetse o hlakola basebelisi bohle le monoana oa ho kenya.
- Tlhokomeliso: Ts'ebetso ena e tla hlakola yuniti e hokahantsoeng ea relay (RTT, DINRTT kapa RU2)
HO PARA – BIOMETRIC READER LE REMOTE RELAY UNIT
Haeba ho hlokahala ho kenya ts'ireletso, 'mali a ka hokeloa ho yuniti ea relay e hole sebakeng se sireletsehileng, seo le sona se ka bapalang karolo ea konopo ea kopo ea ho tsoa. Latela litaelo tse ka tlase ho li kopanya (ka bobeli) lisebelisoa ka bobeli kapa u bue ka Buka ea Remote Relay.
E kopanya B100-SA v2 le DINRTT
- Koala Jumper. DINRTT e lla e sa phetse, 'me ho panya ha leseli le khubelu.
- Bula jumper
- Emela Beep + OK Beep (e khuts'oane + e khuts'oane + beep e telele) Ka mor'a molumo oa OK, ho kopanya ho etsoa.
E kopanya B100-SA v2 le RTT
- Beha Dipswitch No.1 ho beha ON. RTT e lla e sa khaotse, 'me lebone le lefubelu le panya.
- Beha Dipswitch No.1 ho emisa.
- Emela Beep + OK Beep (e khuts'oane + e khuts'oane + beep e telele) Ka mor'a molumo oa OK, ho kopanya ho etsoa.
E kopanya DINB100-SA le RU2
- Beha Jumper sebakeng se koetsoeng. RU2 e lla e sa khaotse 'me ho panya ha lebone le khubelu.
- Beha Jumper sebakeng se bulehileng.
- Emela Beep + OK Beep (e khuts'oane + e khuts'oane + beep e telele) Ka mor'a molumo oa OK, ho kopanya ho etsoa.
Tlhokomeliso: Ho fetola monoana oa ADMIN hape ho tla hlakola yuniti ea relay e hole.
MOLAOLI LETHATA
Sebelisa menoana ea ntlha joalo ka Motsamaisi le Setsi. U ka sebelisa menoana e meng e le menoana ea ho fihlella. Monoana oa motsamaisi o ngolisitsoe qetellong ea ho kenya sistimi. Ngoliso ea pele ea monoana oa Admin e hlalositsoe bukeng ea ho kenya.
ADD Finger Relay 1 (Monoana o tla kenya tšebetsong relay 1)
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso hang |  x 1 |
 ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa Monoana oa Mosebelisi min. Linako tse 6 (ho fihlela ha khutsufatso + e telele) |  x 6 |
 ho panya ka potlako |
mololi o mokhutšoane + o molelele |
ADD Finger Relay 2 (Monoana o tla kenya tšebetsong relay 2)
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 2 | x 2 |
 ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa Monoana oa Mosebelisi min. Linako tse 6 (ho fihlela ha khutsufatso + e telele) | x 6 |
ho panya ka potlako |
mololi o mokhutšoane + o molelele |
Relay 2 e fumaneha haeba 'mali a sebelisoa le yuniti ea relay e hole e nang le li-relay tse 2 (DINRTT le RU2). Ikopanye le setsi haeba Relay 2 e fumaneha tsamaisong ea hau.
ADD Finger Relay 1&2 (Monoana o tla kenya tšebetsong relay 1&2)
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 3 | x 3 |
 ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa Monoana oa Mosebelisi min. Linako tse 6 (ho fihlela ha khutsufatso + e telele) | x 6 |
ho panya ka potlako |
mololi o mokhutšoane + o molelele |
Relay 2 e fumaneha haeba 'mali a sebelisoa le yuniti ea relay e hole e nang le li-relay tse 2 (DINRTT le RU2). Ikopanye le setsi haeba Relay 2 e fumaneha tsamaisong ea hau.
HLAKOLA Monoana
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 4 | x 4 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa Monoana oa Mosebelisi | x1 |
 ho panya ka potlako |
mololi o mokhutšoane + o molelele |
HLAKOLA Menoana
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 4 | x 4 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | ho panya butle |
bipi e khuts'oane | |
| Swaepa Monoana oa Tsamaiso makhetlo a 2 | x2 |
ho panya ka potlako |
li-beep tse ngata |
FETOHA MOLAOLI Monoana
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 5 | x 5 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | ho panya butle |
bipi e khuts'oane | |
| Swaepa Monoana o MOCHA oa Tsamaiso min.6 linako | x6 |
ho panya ka potlako |
mololi o mokhutšoane + o molelele |
FETOHA/Ngolisa INSTALLER Monoana
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Tsamaiso makhetlo a 6 | x 6 |
 ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | ho panya butle |
mololi o mokhutšoane + o molelele | |
| Swipe NEW Installer Finger min.6 linako tse ling | x6 |
ho panya ka potlako |
3 li-beep tse khutšoane |
Sets'oants'o sa thibelo ea Lenaneo la Tsamaiso
Swaepa ADMIN Monoana makhetlo a 1 ho isa ho a 6 ho latela lenane leo u le batlang
MOEKETSI LETSATSI
Beha Relay Nako e 1 (ka sekepeng)
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swaepa Monoana oa Motlakase 1 nako | x1 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa INSTALLER Monoana 'me u qale ho bala metsotsoana | x1 |
ho panya ka potlako |
lla ka motsotsoana o le mong |
| Swaepa Monoana oa INSTALLER ho emisa kapa ho ema metsotsoana e 30 ho kenya relay mokhoeng oa toggle. | x1 |
|
mololi o mokhutšoane + o molelele |
Beha Relay 2 Nako (hole)
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swipe Installer Finger makhetlo a 2 | x2 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swaepa INSTALLER Monoana 'me u qale ho bala metsotsoana | x1 |
ho panya ka potlako |
lla ka motsotsoana o le mong |
| Swaepa Monoana oa INSTALLER ho emisa kapa ho ema metsotsoana e 30 ho kenya relay mokhoeng oa toggle. | x1 |
|
mololi o mokhutšoane + o molelele |
Relay 2 e fumaneha haeba 'mali a sebelisoa le yuniti ea relay e hole e nang le li-relay tse 2 (DINRTT le RU2). Ikopanye le setsi haeba Relay 2 e fumaneha tsamaisong ea hau.
BUZZER ON/OFF
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swipe Installer Finger makhetlo a 3 | x3 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swipe Monoana oa Setsi | x1 |
ho panya ka potlako |
mololi o mokhutšoane + o molelele |
LEKHANYA LE BULETSE / TIMETSE
| Ketso | Monoana | Backlight | Buzzer Molumo |
| Swipe Installer Finger makhetlo a 4 | x4 |
ho panya butle |
bipi e khuts'oane |
| Ema metsotsoana e 5 (ho fihlela ho panya ka potlako) | bipi e khuts'oane | ||
| Swipe Monoana oa Setsi | x1 |
ho panya ka potlako |
mololi o mokhutšoane + o molelele |
Setšoantšo sa "Installer Programming block"
Sehlahisoa sena mona se lumellana le litlhoko tsa taelo ea EMC 2014/30/EU. Ho feta moo, e lumellana le RoHS2 Directive EN50581:2012 le RoHS3 Directive 2015/863/EU. www.xprgroup.com.
Litokomane / Lisebelisoa
 |
xpr B100-SA Standalone Biometric Reader [pdf] Tlhophiso Tataiso B100-SA Standalone Biometric Reader, B100-SA, Standalone Biometric Reader, Biometric Reader, Reader |