M2M Easy 2 Security Communicator®
- Tataiso ea ho kenya Kapele (bakeng sa PCB v9.17, v9.27)

LIEKETSENG LEKHOTLA

1. SIM card slot (mofuta oa 2FF, push-insert)
2. Sehokelo sa Antenna (SMA-50 Ohm, mosali)
3. PWR -/+: Sehokelo sa thapo ea matla (8-24VDC, 1A), khokahanyo ea betri
4. IN1, IN2 -/+: lihokelo tsa thapo tsa ho kenya (bakeng sa li-sensor, sabotage bonoa)
5. Li-Jumpers bakeng sa ho khetha mekhoa ea mela ea ho kenya (bakeng sa IN1, IN2):
   – galvanically indepentent voltage inputs
   - lisebelisoa tsa ho ikopanya (ho lemoha terata e khaotsoeng (ka ho sebelisa 10kΩ EOL resistor), kapa e khutšoanyane)
6. Maemo a li-LED
7. OUT: tlhahiso ea relay (bakeng sa taolo: ho buloa ha heke kapa siren / makhapetla)
8. LR: Alamo (TIP RING) mohala oa ho hokahanya setsi sa alamo (mohala oa mohala oa analog o etsisitsoeng)
9. PROG: sehokelo sa micro-USB (bakeng sa tlhophiso, ho khatholla software)
10.  Likoti tsa ho tiisa boto ea PCB (ka lebokoseng la tšireletso la alamo, joalo-joalo)
11. Sehokelo sa boto ea katoloso (bakeng sa IO-expander)

Khetho ea mokhoa oa ho kenya letsoho (ka li-jumpers [5]):

• Mokhoa oa ho kenya lebitso (bakeng sa ho khaola ha cable / ho lemoha nako e khutšoanyane kapa li-sensor)
  • Li-jumpers tse amanang le tsona (haufi le 2-pins, haufi le sehokelo sa ho kenya)
  • Ntlha ea motheo ea mela e kenyang (-) e tloaelehile
  • Khokahano ea mela e kenang (polarity e ikemetseng)
• Moqtage
  • Li-jumpers tse amanang le tsona (haufi le li-2-pins ho li-LED tsa ho kenya)
  • Galvanical e ikemetseng, mela e kenang ka bomong
  • Ela hloko polarity ha wiring!

KABELO EA MATLA LE MAEMO A TIKOLOHO

• Matla a matla: 8-24 VDC
• Letšoao la ho kenya: boemo bo phahameng ba 2-24V (IO-expander: 2-32V), boemo bo tlase: 0-1V
• Boemong ba hona joale: 0.33mA
• Switchable voltage ka tlhahiso: 2A / 120VAC; 1A / 24VDC
• Tšireletso: IP21
• Mocheso oa ts'ebetso o pakeng tsa -40°C le+70°C, polokelo e pakeng tsa -40°C le+80°C, ka mongobo oa 0-95%
• Boholo: 96 x 77 x 22mm, boima: 160 gr
• Ho tiisa / ho phahamisa: e kanna ea ts'oaroa ke li-screw tse 4 / li-spacers tsa polasetiki ka masoba a 4 ho PCB.

LIEKETSENG MOHATO

• Mohato oa 1: Beha SIM ka har'a terei ea SIM [1] (lehlakore la chip le shebile fatše 'me moeli o sehiloeng oa SIM o shebile lehlakoreng la PCB).
• Mohato oa 2: Sututsa SIM ho fihlela e tla lokisoa.
• Mohato oa 3: Thala 'me u hokahane le mela (li)sebelisi bakeng sa lisensara kapa sabotage discover) ka voltage/contact mode - ka ho kenya likhoele ho IN1, IN2 [4].
  Khetha mokhoa oa ts'ebetso oa mohala oa ho kenya, khetha boemo ba jumper [5] (voltage/kopana). Hokela tlhahiso (bakeng sa ho chencha sesebelisoa sa kantle / sistimi ea ho bula heke) ho OUT [7].
• Mohato oa 4: Haeba u batla ho hokela setsi sa alamo ho transmitter ea rona ea polokeho, joale hokela TIP RING ea setsi sa alamo boema-kepeng ba ALR [8].
• Mohato oa 5: Hokela lenakana ho sehokelo sa SMA [2].
• Mohato oa 5: Lenaneng la puisano la setsi sa alamo, kenya bonyane nomoro e le 'ngoe ho nomoro ea mohala ea leihlo e hole. Haeba u lakatsa ho sebelisa M1M Easy 2 ka mokhoa oa GSM hape (e le tsela ea mantlha kapa ea bobeli), kenya nomoro ea mohala ea GSM. ea tšebeletso ea dispatcher ho kena setsing sa alamo.
• Mohato oa 6: Hokela thapo ea USB-microUSB ho PROG e nang le sehlooho se reng [9], 'me u etse peakanyo bakeng sa sesebelisoa sa EasyTerm ho latela karolo e amanang le Bukana ea Mosebelisi.
• Mohato oa 7: Khoasolla EasyTerm sehokelong sena (Windows® 7/8/10/11 ea sebetsa): https://www.m2mserver.com/m2m-downloads/EasyTerm_v1_3_5__EN.zip
• Mohato oa 8: Khoasolla firmware ea morao-rao bakeng sa ho nchafatsa software: https://www.m2mserver.com/m2m-downloads/EASY2S_V21R09E05RC08.bin
• Hata 9: Ntša EasyTerm ZIP file, le ho kenya software ea EasyTerm_v1_3_5.exe. Latela mehato ea bukana ea ho kenya Khaolo ea 4, 5.
• Mohato oa 10: Hokela thapo ea motlakase ea 12V/24V DC ea lithapo tsa motlakase tsa setsi sa alamo ho boema-kepe bo nang le sehlooho se reng PWR [3]. (Ela hloko haholo polarity ea terata! Mohala o ka letsohong le letšehali oa PWR ke positi (+), ka ho le letona ke negative (-). U ka sebelisa adaptara ea motlakase ea 124V DC 1A hape.)
• Mohato oa 11: Joale sesebelisoa se tla ba tlas'a voltage, 'me e tla be e bulela le ho qala ts'ebetso ea eona. PWR LED e tala e tla lula e khantša. Boemo bofe kapa bofe bo bong ba ts'ebetso ea LED bo thathamisitsoe mona.

BOHLOKOA! Haeba ho se na PC e fumanehang, o ka seta liparamente tsa sesebelisoa ka melaetsa ea mongolo ea SMS (ka ho sebelisa litaelo tse lumellanang).

LED	Mosebetsi	Tlhaloso	Mmala oa LED	Boitšoaro
GSM	Matla a leqhubu la marang-rang a cellular	Ho saena matla a lets'oao a teng - ho benya ho feta = matla a mats'oao a betere	khubelu	tse benyang
STA	Boemo ba modem	Tabeng ea ts'ebetso e tloaelehileng e saena boemo ba puisano ea marang-rang a selefouno	mosehla	kganyang/ kganya
IN1	Kenyelletso nr.1	E tšoaea boemo ba mohala oa #1 oa ho kenya (I1INV kapa IDELAY parameters e sebelisoa) Lebone la LED lea khantša haeba lithapo tsa ho kenya li koetsoe (li sebetsa)	botala	mabone
IN2	Kenyelletso nr.2	E tšoaea boemo ba mohala oa #2 oa ho kenya (I2INV kapa IDELAY parameters e sebelisoa) Lebone la LED lea khantša haeba lithapo tsa ho kenya li koetsoe (li sebetsa)	botala	mabone
TSOA	Phatlalatso ea tlhahiso	LED e khantša ha relay e koetsoe, eseng ho khantša: ha relay e buloa	mosehla	mabone
MDM RDY	Ts'ebetso ea modem	Boemo ba modem. E benya nako le nako haeba modem e sebetsa ebile e fumaneha.	khubelu	tse benyang
ALR	Setsi sa alamo	Boemo ba mohala oa setsi sa alamo (Tip-Ring) Sebuela-pele se khanngoe: ha se khantšitsoe, Sebui se tima: ha ho setsi sa alamo	botala	tse benyang
PWR	Matla	E bontša boteng ba phepelo ea motlakase ea processor	botala	mabone

STA LED - e na le mekhoa e meraro:
- mabone a sa khaotse: pontšo ea ho qetela ea GPRS e atlehile,
- E timiloe: Mokhoa oa ts'ebetso oa GSM, ha ho phoso
- palo ea 'x' ea khanya ka nako ea metsotsoana e 3: khoutu ea phoso (1 Flash: Ho hloleha ha Module, 2 ho benya: Ho hloleha ha SIM card, 3 ho benya: Ho hloleha ha netefatso ea PIN, ho benya ha 4: Sesebelisoa ha se khone ho kena ho netweke ea GSM, 5 ea khanya: Sesebelisoa ha se khone ho kena marang-rang a cellular, 6 ea khanya: E hokahane le marang-rang a cellular, empa ha e khone ho kena ho seva.
GSM LED: Linomoro tsa khanya ea LED li bonts'a matla a hona joale a lets'oao la marang-rang a cellular (ho khanya ho eketsehileng: kamohelo e ntle ea matšoao). Ho na le metsotsoana e 10 pakeng tsa flashings. Khanya e le 'ngoe e nka 50 msec, ebe halofo ea motsotsoana e tsoela pele. Ho benya: 0: Phoso, 1: Ho fokola, 2-3: Karolelano, 4-5: E ntle, 6-7: E ntle haholo
IN1, IN2 LED: Ha kenyeletso e sebetsa (haeba lithapo tse peli li koetsoe; kapa ka mokhoa oa matla ho 5-24VDC voltage teng) e amanang le INx LED e tla khantša.
LED E TSOANG: Ho khantša ha tlhahiso e sebetsa (lithapo tsa relay li koetsoe). E bontša boemo ba "primer-side" ea relay.
LED ea MODEM ea RDY: Opereishene ea mojule LED, e panya ka potlako ha ho qaloa Easy2 (hoo e ka bang habeli ka metsotsoana). Ha modem e se e fumaneha ebile e sebetsa 'me e na le puisano e sebetsang ho marang-rang a GSM, joale e tla benya ka mokhoa o fokolang khafetsa.

MEKHOA TS'EBETSO

Sesebelisoa se khona ho hlophisa le ho sebelisa mekhoa le mesebetsi e latelang:

1. Motlakase oa GSM (o lokiselitsoe pele ho mokhoa ona, ka ho feletseng): tsamaiso ea alamo e hokahane le tlhahiso ea TIP-RING, li-code tsa ID tse kenang li ntse li fetisetsa le ho fetisoa ka lipontšo ka marang-rang a GSM ho ea setsing sa ho romela se hole.
2. Ho tekena ho Enigma IP receiver / SIMS Could® : sisteme ea alamo e hokahane le tlhahiso ea TIP-RING, likhoutu tsa ID tse kenang li ntse li fetisetsa le ho fetisa matšoao ka marang-rang a cellular ka protocol ea Enigma ho moamoheli oa Enigma IP kapa ho SIMS ® software.
3. Ho fetisetsa ka marang-rang a cellular ho ea setsing sa ho romella: alamo e hokahane le ho kenya letsoho TIP-RING, sabo.tage switch e hokahane le ho kenya letsoho bakeng sa ho beha leihlo, matšoao a kenang a fetoleloa ho likhoutu tsa ID tsa Contact ebe o fetisoa ka marang-rang a cellular ho aterese ea IP ea setsi se hole.
4. Sistimi ea alamo e ikemetseng - e nang le tsebiso ea SMS feela: li-sensor orsabotagho fumanoa ha e ho hokahane le mela ea ho kenya (li-inputs tsa 2, tse nang le IO-expansion max. 8 inputs); siren e ka kopanngoa le tlhahiso. Lipontšo li fetisoa ka marang-rang a cellular ho aterese ea IP ea seva.
5. Tlhokomelo ea lintho tse kenang, ho buloa ha heke: lisensara kapa sabotagphumano ea e li hokahane le li-voltage/contact inputs (ka IO-expansion max. 8 inputs). Kenyelletso e khuts'oane / terata e sehiloeng e ka bonoa le ho tse kenang. Sehlahisoa (s) sa relay se laoloa ka thōko (sephetho sa nr # 1. ke sa ho bula heke, lihlahisoa tse ling (nr. 2-4) li hlahisoa bakeng sa ho fetola lisebelisoa tsa ka ntle). Lisebelisoa li sebelisa marang-rang a cellular ka mokhoa ona bakeng sa taolo e hole. Marang-rang a GSM a sebelisetsoa tsebiso le ho lla ka SMS. Letšoao ka marang-rang a cellular (ho ea atereseng ea IP) le ntse le le teng e le khetho.

TLHOKOMELISO KA KHOPOTSO SERIALI

Sesebelisoa se romelloa ka firmware e kentsoeng le tlhophiso ea feme. Ka nako e sa lekanyetsoang - ntle le liphetoho leha e le life tsa tlhophiso - Easy2S e sebetsa e le transmitter ea GSM (matšoao a tsamaiso ea alamo e hokahaneng (ho Tip-Ring) e tla fetisoa ka marang-rang a GSM - ka li-code tsa Contact ID - ho setsi sa dispatcher).
Litlhoko tse ling tsa tlhophiso li ka hlophisoa ka software ea EasyTerm®. Hokela koung ea USB e nyane ea sesebelisoa ka thapo ho koung ea USB ea komporo ea hau.

TLHOKOMELO KA MELAO EA SMS

- O ka romella litaelo tse ling ka molaetsa o tšoanang oa mongolo oa SMS. Litaelo tsa lipotso li ke ke tsa tsoakoa le litaelo tsa taolo!
– Max. Litlhaku tse 158 li ka sebelisoa molaetseng o le mong oa SMS. Melaetsa e tlameha ho ba le litlhaku tse kholo tsa Senyesemane tsa alfabeta feela (ntle le li-char tse khethehileng) kapa linomoro.
- Taelo le karohano ea litaelo lia khoneha ka lets'oao la comma ntle le sebopeho sa sebaka. Boleng ba paramethara (kamora = sebopeho) bo ka ba le letho.
- Molaetseng o mong le o mong oa SMS (!) u tlameha ho sebelisa paramethara ea senotlolo (PW) sebakeng sa pele sa taelo.
- U tlameha ho sebelisa taelo ea RESET molaetseng oa ho qetela oa paramethara ea SMS, qetellong boemo - joalo ka PW=ABCD,……,RESET
- Litekanyetso tse ncha tsa tlhophiso li sebetsa feela ka mor'a ho qala bocha. Ka mor'a - metsotso e 'maloa - u rometse molaetsa oa ho qetela oa paramethara u tla fumana karabo ho tsoa ho sesebelisoa hore na ke li-parameter tse kae tse sebetsitsoeng (mohlala, "Litlhophiso li lokile!" Karabelo ea molaetsa oa mongolo)
– Phasewete ea kamehla ke ABCD, e ka fetoloang (PWNEW param.) e ka bang max. Likotoana tse 16.
- Example: PW=ABCD,APN=TELEMATICS.NET,SERVER1=1.1.1.1,RESET >>> Karabo ya molaetsa wa mongolo: Di-setting OK!

MOHLOMI PARAMETER MELAO	Tlhaloso
PW	Khokahano / netefatso ea password (ea kamehla: ABCD)
PWNEW	Ho fetola phasewete, ho eketsa phasewete e ncha bakeng sa netefatso ea khokahano
APN	Lebitso la netweke ya APN e hlokehang bakeng sa kgokelo ya netweke ya cellular, e fanoeng ke opareitara e fanang ka SIM card
MOSEBETSI1	Aterese ea mantlha e tsitsitseng ea IP ea leihlo le hole (setsi sa dispatcher) bakeng sa ho amohela matšoao a ho fetisa.
POTSO1	Nomoro ea boema-kepe bakeng sa aterese ea mantlha e tsitsitseng ea IP ea setsi sa dispatcher, moo matšoao a tla amoheloa (kamehla=9999)
GPRSEN	E nolofalletsa puisano ea marang-rang ea cellular. Maemo: 1=nomella, 0=thibela (kamehla=0)
SWPROTO	Ke protocol efe e sebelisetsoang ho bontša. Boleng: 2=Tlhakalo (prothokholo e tlwaelehileng ya ID ya Kgokahano), 1=M2M (kamehla=2) (M2M e bolela protocol e fetotsoeng ea Contact ID, e ka sebelisoang feela le ba amohelang IP ba latelang (joalo ka Enigma II).®, Pherekano IP2® baamoheli) software e hole ea dispatcher (joalo ka AlarmSys® le SIMS® software)).
ACCOUNT	Khoutu ea boitsebahatso ea moreki, nomoro ea ntho e tla sebelisoa bakeng sa matšoao a hau, mats'oao (a lintho tse kenang) tse rometsoeng ke sesebelisoa (default=0001). Ho khothalletsoa ho theha nomoro ea ntho e tšoanang le e behiloeng setsing sa alamo!
MOSEBETSI	U ka khetha hore aterese ea IP ea mantlha kapa ea bobeli e tla ba ea pele ka tatellano ea lipontšo
DTMFTIME	DTMF khefutsa pakeng tsa matshwao a ID ya TIP-RING
IPPROTO	TCP kapa protocol ea puisano ea UDP ho latela litlhoko tsa ho lumellana
LFGSMREQ	Maqhubu a lets'oao la bophelo la GSM - boleng ka metsotsoana (kamehla = 60)
LFFREQ	Khafetsa ea lets'oao la bophelo ba netweke ea cellular - boleng ka metsotsoana (default=300)

POTSO MELAO	Likahare tsa karabo
INFDEV (kapa) DEVSTAT	E tla arabela tlaleho ea SMS ka boemo ba hajoale ba Easy 2: account nr. (ID ea moreki), matla a pontšo, mofuta oa software, ID ea Hardware, IMEI ea sesebelisoa, SIM ICC, boemo ba betri, aterese ea IP (ACCOUNT, SQ, SWVER, HWID, IMEI, SIMICC, VBATT, IP)
INFIO	Boemo ba hona joale ba mela ea ho kenya le mola oa tlhahiso. E na le: ACCOUNT, SQ, boemo ba hajoale ba li-input/line line
INFLEL	Litlhophiso tse hlophisitsoeng tsa tsebiso ea lentsoe/SMS, linomoro tsa mohala le tatellano ea litemoso (molaetsa oa mongolo oa SMS), tatelano ea tatellano ea mohala oa lentsoe (ho lla) e tla ba karabo. E na le: ACCOUNT, SQ, TEL1, TEL2, TEL3, TEL4, I1S, I2S, I1V, I2V
INFSMS	Kenya litlhophiso tsa tsebiso ea SMS. E na le: ACCOUNT, SQ, I1ON, I1OFF, I2ON, I2OFF
INFIP	Litlhophiso tsa khokahano ea seva. E na le: ACCOUNT, SQ, IMEI, IP, SERVER1, PORT1, SWPROTO

MOLAETSA WA SMS (TAELO TSA TAELO) EXAMPLES:

• GSM signaling/transmitting: PW=ABCD,GPRSEN=0,SYS1=1,ACCOUNT=1130,LFGSMFREQ=60,DTMFTIME=60,RESET
• E tekena ka marangrang a cellular ho IP-receiver: PW=ABCD,GPRSEN=1,SFUNCT=1,ACCOUNT=1130,LFFREQ=300,APN=NET,SERVER1=89.133.189.139, PORT1=9999,IPPROTO=UDP,RESET

Bakeng sa ho lekola liparamente tse ling tse fumanehang, bala Tataiso ea Tlhophiso ea M2M Easy2S Security Communicator e ka khoasolloang ho rona. websebaka: https://m2mserver.com/en/product/wireless-safety-transmitter/
Sehlahisoa sena se tšoailoe ka letšoao la CE ho latela melaoana ea Europe.

Litokomane / Lisebelisoa

WM SYSTEMS M2M Easy 2 Security Communicator System [pdf] Tlhophiso Tataiso M2M Easy 2 Security Communicator System, M2M, Easy 2 Security Communicator System, Security Communicator System, System Communicator, System

Litšupiso

• Bukana ea Mosebelisi