Likhopolo tsa ho rekisa AP 6000 ho Tšehetso e le 'ngoe ea Boto

Litlhaloso tsa Sehlahisoa:

• Tlhophiso ea makoloi: E ka hlophisehang
• Coinmech le Bill Acceptor Configuration: MDB kapa Pulse Bill Validator
• Tshebetso Voltage: 110-volt kapa 24-volt
• Likhetho tsa ho Tefo: Sebali sa Karete, Mofetoleli oa Lichelete, Moamoheli oa Bill

Litaelo tsa Tšebeliso ea Sehlahisoa

Lokisa Motors le Liphoso tse Hlakileng:

1. Tobetsa konopo ea mofuta oa ts'ebeletso e mosehla kapa o moputsoa ho kenya SERVICE MODE.
2. Haeba SYS ERR e hlaha, tsamaisetsa tlase hang ebe o emisa. Haeba Motor Errors e hlaha, tobetsa HLAHLOLA.
3. Tobetsa ENTER/EXECUTE ho fihlela MAIN/MENU e bonahala bakeng sa liphoso tse ling.
4. Tsamaisetsa tlase ho CONFIGURE ebe o tobetsa ENTER/EXECUTE.
5. Tsamaisetsa tlase habeli ho Configure Motors ebe o otla ENTER/EXECUTE.
6. Emela hore palo ea enjene ea mochini e hlahe.
7. Tobetsa CANCEL ho khutlela ho MAIN/MENU.

Lokisa Coinmech le Moamoheli oa Bill:

• Haeba u sebelisa PULSE BILL VALIDATOR:
  • Eya ho OPTIONS ebe o tobetsa ENTER/EXECUTE.
  • Beha BILL VAL ho PULSE.
  • Netefatsa hore switch 7 e BUTSE 'me switjha 8 e TLOHILE bakeng sa mokhoa oa ho otla ha pelo.
  • Hlahloba hore na ea amohelang o behiloe bakeng sa lebelo le lekhutšoanyane (50ms).
• Bakeng sa mofuta oa MDB, etsa bonnete ba hore switch 7&8 E TIMA bakeng sa lihlahisoa tsa MEI/MARS.
• Sheba tokomane e fanoeng ea Litlhophiso le Litaelo tsa Tšebeliso bakeng sa liphetoho tse khethehileng tsa ho fetola nomoro ea mohlala.

Theko ea Morekisi:

1. Tobetsa konopo ea mokhoa oa tšebeletso ho hlahloba liphoso tsa sistimi.
2. Haeba mathata a ntse a tsoela pele, etsa bonnete ba hore tlhophiso e nepahetseng ea koloi le litlhophiso tsa sesebelisoa sa ho lefa.
3. Netefatsa hore mokoloto oa kamehla oa 'mali oa karete o lumellana le theko e holimo haholo ea sehlahisoa.
4. Sheba Litaelo tsa Tlhophiso le Tšebeliso bakeng sa mehato e meng ea ho rarolla mathata.

Lipotso Tse Botsoang Hangata

P: Nka rarolla mathata joang haeba mochini o bonts'a liphoso ka mor'a ho hlophisoa?
A: Sheba tlhophiso ea koloi, litlhophiso tsa sesebelisoa sa ho lefa, 'me u bue ka litaelo tse fanoeng bakeng sa mehato e itseng ea ho rarolla liphoso.

P: Na 24v MEI/MARS e netefatsang e ka fetoleloa ho ts'ebetso ea MDB?
A: E, e ka fetoloa ka phetoho e bonolo ea MDB e fumanehang ka thoko.

KAPELE QALANG LENANEO TATAISO

MOKHOA OA HO HLOMELA LENANEO LA LEBOTO LE NCHA

Hang ha hardware e kentsoe, hoa hlokahala ho hlophisa molaoli bakeng sa mochine o itseng. Ts'ebetso ea mantlha ea ho hlophisa kit efe kapa efe ea In One e hlile e ts'oana. Haeba u sebelisa khiti e nang le mochine o fetolang chelete ea tšepe eo e seng oa MDB kapa se tiisang sekoloto, ka kopo sheba leqephe la 15 la Tokomane ea Litaelo tsa Tlhophiso le Tšebeliso e tlang ka lebokoseng la lisebelisoa bakeng sa Litlhophiso tsohle tse hlokahalang tsa Pulse Bill Validator. Ho E 'ngoe, balaoli ba sebelisa li-switches tse khubelu tse nang le li-switches tse 2 kapa tse 6 tse tšoeu tse setang konopo, switch ea mamati, mofuta oa mochini le tšehetso ea sensor. Litlhophiso tsena li ka fumanoa leqepheng la 1 & 2 la Litaelo tsa Tlhophiso le Tšebeliso.

KIT E KHETHEHILENG KEYPAD TSEBISO

Kit ka 'ngoe e ka sebelisa linotlolo tse fapaneng ho etsa mesebetsi e itseng. Ka kopo ela hloko tse sebelisitsoeng bakeng sa kit ea hau pele u tsoela pele.

Mofuta oa Kit	Phetha	Senotlolo	Hlakola Senotlolo	U    Senotlolo	Tlase Key
RVMC-6/7000-x	14		12	11	13

Lokisa MOTHO LE HO HLAKOLA LIPHOSO

Kenya SERVICE MODE ka ho tlanya konopo ea mofuta oa ts'ebeletso e mosehla kapa o moputsoa. Pontšo e lokela ho bonts'a "MAIN/MENU" kapa "SYS ERR". Haeba u bona "SYS ERR" (liphoso tsa sistimi), tsamaisetsa tlase hang 'me U EME. Haeba "Motor Errors" e hlaha skrineng (sena ke ntho e tloaelehileng nakong ea ho kenya qalong), tobetsa konopo ea CANCEL. Joale o lokela ho bona "MAIN/MENU". Bakeng sa liphoso tse ling tse teng, tobetsa konopo ea ENTER/EXECUTE ho fihlela "MAIN/MENU" e bonahala.

Tsamaisetsa tlase ho "CONFIGURE" ebe o tobetsa konopo ea ENTER/EXECUTE. Tsamaisetsa tlase makhetlo a 2 ho "Configure Motors" 'me u tobetse konopo ea ENTER/EXECUTE. U tla bona "ka kopo ema ..." e lateloa ke palo ea makoloi a mochini. Mookameli o penya li-motor tsohle ebe o khutla le seo a se bonang, mohlalaample, “ke kopa o eme…45 motors”. Tobetsa konopo ea CANCEL ho khutlela ho "MAIN/MENU".

HLOMELA COINMECH LE MOAMOHELO WA BILL

Hlokomela: Haeba lisebelisoa tsohle tsa ho lefa e le MDB, ha ho na liphetoho tsa mokhoa oa litšebeletso tse hlokahalang, empa li-tubes tsa chelete ea tšepe li lokela ho tlala bonyane halofo e le hore mochine o itlhokomele.

BOHLOKOA: Balaoli ba InOne ba ka tšehetsa li-micromech, li-valdators tsa pulse bill le lisebelisoa tsohle tsa ho lefa tsa MDB. Hoa khonahala ho hokahanya legacy ka bobeli (original pulse/micromech) le ho sebelisa MDB ho molaoli oa InOne. Haeba u na le se netefatsang sa MDB 'me u hokela lehare ho tloha mochining ho ea ho molaoli, u etsa hore lisebelisoa ka bobeli li se ke tsa sebetsa. Lebaka ke hobane lefa le MDB li ikamahanya bakeng sa mofuta o tšoanang oa sesebelisoa sa ho lefa. U tlameha ho sebelisa marapo a le mong feela bakeng sa sesebelisoa sa ho lefa se sebelisoang ebang ke pulse kapa MDB. Sena se sebetsa le ho li-changer. Haeba u sebelisa mochine oa ho fetola MDB, u se ke ua hokela mochine o fetolang micromech ho tloha khabineteng ho ea ho molaoli kapa u tla thibela mochine oa MDB ho sebetsa. Molao oa letsoho o lokelang ho lateloa ke ho hokela lithapo tse tla sebelisoa le molaoli e mocha. Haeba u sa sebelise pulse validator kapa micromech changer joale u se ke ua hokela lithapo tseo holim'a boto.

HAEBA U SEBELISA TLHOKOMELISO EA PULSE BILL:
Eya ho "LIKHETHO" 'me u tobetse ENTER/EXECUTE konopo. Beha "BILL VAL ho PULSE".
Haeba u sebelisa MEI/MARS ka mokhoa oa MDB, etsa bonnete ba hore switch 7&8 TIMA. Bakeng sa mokhoa oa ho otla ha pelo, seta switch 7 ON le 8 OFF. Etsa bonnete ba hore moamoheli o behiloe bakeng sa pulse e khuts'oane (50ms).

HLOKOMELA: Ba amohelang likoloto ba na le linomoro tsa mohlala oa linomoro tse 4. Liphetoho tsohle tse lokelang ho etsahala li ka fumanoa leqepheng la 15 ho Tokomane ea Litaelo tsa Tlhophiso le Tšebeliso e fanoeng le kit. Bakeng sa lihlahisoa tsa MEI/MARS, nomoro ea ho qetela ea nomoro ea mohlala e bontša matla a ho sebetsatage. Haeba moamoheli oa likoloto a qetella ka "1" (joaloka VN2501) joale ke 110-volt pulse bill validator feela. Haeba u na le moamoheli ea qetellang ka "2" (VN2512 bakeng sa mohlalaample) joale ke 24-volt validator.

Sehlahisoa sefe kapa sefe sa 24v MEI/MARS se ka fetoloa ho tloha ho pulse ho ea ho ts'ebetso ea MDB ka phetoho e bonolo ea MDB e fumanehang libakeng tse ling.

HAEBA U SEBELISA 'DUMBMECH' CHANGER:

BEHA KHOPI LEVEL KHOPOTSO
Ho "LIKHETHO" menu, beha COIN LEV MEM ho ON. Joale qala boto ka phetoho e le hore moamoheli oa bili ea pulse a khonehe. Tsoa ho menu ea "OPTIONS" ka ho tobetsa konopo ea CANCEL 'me u nyolohele ho "TLATSA / HLAHALA". Tobetsa ENTER/EXECUTE konopo. Pontšo e tla bala "Khetha Tube 1 -5 kapa kenya lichelete tsa tšepe". Tobetsa 1,2,3 holim'a letlapa la likonopo 'me u netefatse nickel, dime le "quarter dispense". Joale kenya tse leshome tsa mofuta o mong le o mong oa tšepe ka sekoting sa tšepe sefahlehong sa mochini. U SE KE UA tlatsa li-tubes tsa tšepe ho tloha ka morao, lichelete tsa tšepe li hloka ho feta karolong e amohelang ho baloa ponts'ong ea thekiso. Li-Validators HA LI TLA sebetsa ntle le haeba molaoli a bona phetoho ea ho fana ka thekiso ea sekoloto.

HLOKOMELA MOLAOLI
Kamora ho kenya molaoli ka lichelete tsa tšepe, tima mochini, ema metsotsoana e 5 ebe o bula hape. Mochine o tla tsosolosoa, 'me moamoheli oa likoloto o lokela ho sebetsa ka tlhophiso e ncha (haeba e fetotsoe). Ea amohelang o lokela ho bontša hore e nolofalitsoe ka lebone le khubelu le tiileng. Haeba moamoheli a bonts'a mabone a 2, sena se bolela hore o holofetse mochining. Sena se ka etsahala haholo hobane molaoli o nahana hore mofetoleli oa tšepe a ke ke a fana ka lichelete tse lekaneng kapa ho na le bothata ba hardware ka mochine oa tšepe. Etsa thekiso ea lichelete tsa tšepe tse 3-4 'me u tima mochini le ho khutlisa, beha leihlo la hau ho motho ea amohelang chelete. Leseli le lokela ho fetoha ho tiea nakoana. Haeba ho joalo, kenya sekoloto. Haeba ho se joalo, etsa lihlahisoa tse ling tse 'maloa ka lichelete tsa tšepe e le hore boto e bale lichelete tsa tšepe tseo mohopolong. Netefatsa hore COIN LEV MEM e laetilwe ho "OPTIONS." Leka likoloto hape 'me u netefatse hore phetoho e nepahetseng e fanoe ka mor'a hore thekiso e atlehe. Ka kopo elelloa hore mochini o hloka ho tsamaisoa ka baesekele hore moamoheli oa likoloto a sebetse ka mor'a hore ho behoe tlhophiso ea pele ka mokhoa oa ts'ebeletso. Mookameli o tlameha ho bona lichelete tsa tšepe ho chencheng ho etsa hore validator e amohele likoloto. Hangata li-validators tse sa sebetseng hantle ke hobane mofetoheli o hloka ts'ebeletso kapa a na le phoso, ha se phoso ea mohlahlobi oa likoloto maemong a mangata empa ke mofetoleli.

THEKO MOEKETSI

Ho tloha ho "MAIN/MENU" theolela tlase ho "PRICE" ebe o tobetsa konopo ea ENTER/EXECUTE. O ka theko ea mochini o sebelisa likhetho tse 3 tsa menyetla, SINGLE PRODUCT, ENTIRE TRAY, kapa ENTIRE MACHINE. Beha MACHINE OHLE bakeng sa theko e tloaelehileng haholo, theko e latelang literei tsohle tse nang le thepa e tšoanang ea theko, ebe qetellong u ea sehlahisoa se le seng ho lokisa khetho ea motho ka mong. Tsoa ho mokhoa oa ts'ebeletso ka ho tobetsa konopo ea ho hlakola kapa ho tobetsa konopo ea mokhoa oa ts'ebeletso. Koala morekisi ka metsotsoana e 5 ebe o bula hape. Koala lemati la mochini 'me u etse thekiso ea lichelete tsa tšepe le barekisi ba likoloto 'me u netefatse hore u fumana phetoho e nepahetseng. O qetile ho hlophisa. Haeba lisebelisoa tsohle li sebetsa ka mokhoa o tloaelehileng, tsoela pele ka zip tie stray cabling le ho lokisa khabinete e le hore basebetsi ba seke ba hula mohala ka phoso ba baka mohala oa ts'ebeletso. Haeba sesebelisoa se le seng kapa tse ngata tsa tefo li sa sebetse, tobetsa konopo ea "service" 'me u hlahlobe liphoso tsa sistimi. Ho ka etsahala hore ebe li-motor ha lia hlophisoa hantle, kapa mohlomong sesebelisoa sa tefo se behiloe ka phoso kapa mochini le/kapa khetho ha e so rekisoe. Bakeng sa litaba tsa tefo ea 'mali oa karete, etsa bonnete ba hore mokitlane oa kamehla oa 'mali oa karete o lekana le sehlahisoa sa theko e phahameng ka ho fetisisa se rekisoang, haeba ho se joalo,'mali oa karete a ka re ntle le marang-rang ke morekisi mme a se amohele tefo. Mehato e meng ea ho rarolla mathata e ka fumanoa ho Configuration le Litaelo tsa Tšebeliso.

HO HLOMELA LIHLOOHO - HO KHETHOA

Haeba li-sensor li tla kengoa, sheba leqephe la 1&2 la Litaelo tsa Tlhophiso le Ts'ebeliso bakeng sa litlhophiso tse nepahetseng tsa switch. Ka tloaelo switjha 4 e buletsoe ho thusa tšehetso ea sensor, balaoli ba bang ba ka sebelisa switch 2 bakeng sa tšehetso ea sensor.
Ha o ntse o le Mokgweng wa Tshebeletso, kgetha "OPTIONS", ebe "MOTOR STOP". Tobetsa ENTER ho fihlela "DROP" kapa "BOTH" e khethiloe. 'BOBEbeli' ke sebaka se khothaletsoang bakeng sa bareki ba shebaneng le sechaba ha "DROP" e sebelisoa bakeng sa bareki ba ts'ebeliso ea letsatsi le letsatsi.

Ha e setiloe bakeng sa "BOTHO", enjene e tla fetola phetoho e le 'ngoe ka botlalo pele molaetsa o reng "Ke kopa o etse khetho e 'ngoe" o hlaha. Enjene e tla khutlela sebakeng sa 6:2 'lapeng'. Ha e behiloe "DROP", enjene e fetola lebelo le le leng ka lebelo le felletseng ebe e potoloha halofo ea lebelo ka makhetlo a 3-6 ho feta ho qobella ho theoha ha sehlahisoa. Hang ha sehlahisoa se theoha, enjene e tla lula sebakeng sa eona sa hajoale, e ke ke ea khutlela lapeng ka hora ea XNUMX. Haeba li-sensor li hlōleha nakong ea ts'ebetso ea mochine, molaoli o tla fetola boemo ba MOTOR STOP HOME ho tsoela pele ka ts'ebetso e tloaelehileng ho fihlela phoso ea sensor e ka rarolloa.

Litokomane / Lisebelisoa

Likhopolo tsa ho rekisa AP 6000 ho Tšehetso e le 'ngoe ea Boto [pdf] Bukana ea Mosebelisi AP 6000, AP 7000, AP 6000 In One Board Support, AP 6000, In One Board Support, One Board Support, Boto Tšehetso, Tšehetso

Litšupiso

• Bukana ea Mosebelisi