Tempco TPC40034 Power Control Console Bukana ea Mosebelisi
LIEKETSENG TS'OANELO
Lilaoli tsa Mocheso: Mohlala oa TEC-9400, 1/16 DIN Dual Display e nang le PID Auto-tuning
Maikutlo a Sensor: Tlanya "J" thermocouples
Mele ea Khokahanyo: Ntsho
Khoele ea Matla/voltagKeletso: 240VAC, 50/60 HZ, 15A
Liphetho tsa Heater: 3A Max, 720 watts max sebaka ka seng.
Lisebelisoa tse hlahisoang: Li-Relay tsa Naha tse Tiileng
Sesebelisoa sa Power Main: E sebakeng se ka pele
Main Power Fuse: Sheba lenane la likarolo tse ling leqepheng le latelang (le ka morao)
Li-Fuse tsa Taolo: Sheba lenane la likarolo tse ling leqepheng le latelang (le ka morao)
TEMOSO
- Maqhubu a moea a kaholimo le tlase ho khomphutha ha a tlameha ho thibeloa! Ho thibela boemo ba mocheso o feteletseng, likarolo tsa ka hare li tlameha ho lula li le haufi le mocheso oa kamore (75ºF / 24ºC) kamoo ho ka khonehang.
- Voltage khonang ho baka kotsi kapa lefu e teng ka har'a khomphutha ena. Motlakase oa lisebelisoa tsohle o tlameha ho hangoa pele o kenya kapa o qala mekhoa ea ho rarolla mathata. Wiring e hlahisoang ke heater le ho nchafatsa likarolo li tlameha ho etsoa ke basebetsi ba nang le litsebo feela.
- Ho fokotsa monyetla oa ho ba le mollo kapa ho tšoha, u se ke ua pepesetsa console ena pula kapa mongobo o feteletseng.
- Se ke oa sebelisa console ena libakeng tseo ho tsona maemo a kotsi a leng teng joalo ka ho thothomela ho feteletseng, ho thothomela, litšila, likhase tse senyang, oli kapa moo ho nang le likhase tse phatlohang kapa mouoane.
- Ho khothaletsoa ka matla hore ts'ebetso e kenyelletse Taolo ea Limit joalo ka Tempco TEC-910 e tla koala lisebelisoa maemong a ts'ebetso e seng e setiloe molemong oa ho qoba tšenyo e ka bang teng ho lihlahisoa kapa litsamaiso.
KHOPO (Bakeng sa polokeho, khaola mehloli eohle ea motlakase pele o kenya mohala)
- Hokela li-lead tsa mofuta oa hau oa "J" thermocouples ho li-plug tse nyane tse fanoeng. Hlokomela polarity e nepahetseng. Loto e khubelu ke (-) negative.
- Mocheso oa mocheso oa mocheso o hlahisoa ka ho toba ka mohala oa mohala. Mehaho ea ka morao ea li-console le li-plug tsa Hubbell tsa ho nyalana li fana ka matla a laoloang a phelang bakeng sa khokahanyo e tobileng ho heater ea hau. Hokela lead e le 'ngoe ho tloha ho heater ea hau ho prong e le' ngoe ea polaka ea Hubbell (eseng fatše). Hokela letoto le leng ho tloha ho hitara ea hau ho ea ho prong e 'ngoe. Hokela mobu oa futhumatsang (haeba ho hlokahala) ho khokahanyo ea fatše (G) holim'a polaka.
TS'EBETSO
- Netefatsa hore sesebelisoa sa motlakase se timme. Hokela lihitara le li-thermocouples ho lihokelo tse ka morao. Hokela thapo ea mohala e fanoeng ho tsoa ho khomphutha ho ea sebakeng se tloaelehileng sa 240V, 15A. Tlosa console.
- Beha boemo ba mocheso oo u o batlang ka ho sebelisa likonopo tsa metsu ea holimo le tlase ho lilaoli tsa mocheso tsa TEC-9400.
- Sheba maqephe a latelang bakeng sa ts'ebetso e felletseng le leqephe la 4 & 7 bakeng sa tokiso e ikemetseng ea lilaoli tsa mocheso oa TEC-9400.
PHEELLO/ PUSO
| Nomoro ea Karolo ea Tempco | Tlhaloso |
| EHD-124-148 | Fuse (1), e fuoe lintlha tse 15 Amp/250V, ¼ x 1 ¼”, e sebetsang ka potlako BUSS ABC-15-R. E sebelisoa bakeng sa matla a mantlha a taolo ea console. |
| EHD-124-297 | Fuse (1), e fuoe lintlha tse 1½ Amp/ 250V, ¼” x 1¼”, ho lieha ha nako, BUSS MDA-1½ -1-R. E sebelisoa bakeng sa balaoli ba TEC-9400. |
| EHD-124-282 | Li-Fuse (4), li fuoe lintlha tse 4 Amp/ 250V, ¼” x 1¼”, e sebetsang ka potlako, BUSS ABC-4-R. E sebelisoa bakeng sa lihlahisoa tsa hitara ka bomong. |
| EHD-102-121 | Li-plugs tsa tlhahiso ea matla (1 ka libaka), Hubbell HBL4570C, 15A 250V Twist-Lock. |
| TCA-101-105 | Tlanya "J" thermocouple mini plug (1 ka zone), e Ntšo |
HLOKOMELA: Bakeng sa li-fuse tsohle, sebelisa linomoro tsa likarolo tsa BUSS tse thathamisitsoeng kapa tse lekanang.
TŠEBELETSO KOPANE
SROLL KEY:
Senotlolo sena se sebelisetsoa ho tsamaea ka har'a menu ho khetha paramethara ho ba viewed kapa e lokisitsoe.
SEHLOOHO:
Senotlolo sena se sebelisetsoa ho eketsa boleng ba parameter e khethiloeng.
SEHLOOHO SE TLASE:
Senotlolo sena se sebelisetsoa ho fokotsa boleng ba parameter e khethiloeng.
RESET KEY:
Senotlolo sena se sebelisetsoa ho:
- Khutlisetsa skrineng sa lapeng.
- Seta alamo bocha hang ha boemo ba alamo bo tlositsoe.
- Emisa mokhoa oa ho laola ka letsoho, mokhoa oa ho Itokisa kapa mokhoa oa ho lekanya.
- Hlakola molaetsa oa phoso oa Tokiso kapa oa puisano.
- Qala hape sebali sa nako ha sebali sa nako se felile.
- Kenya menu ea taolo ea letsoho haeba mokhoa oa ho hloleha o etsahala.
Kenya SEHLOOHO: Tobetsa 
'me u tšoare metsotsoana e 5 kapa ho feta ho:
- Kenya menu ea ho seta. Pontšo e tla hlaha
- Kenya mokhoa oa ho laola ka letsoho. Tobetsa o hatelle mokgoa. Pontšo e tla hlaha.
- Kenya mokhoa oa Auto-Tuning. Tobetsa o hatelle bakeng sa metsotsoana e 7.4, ebe u tlohela ho khetha mokhoa oa Auto-Tuning. Pontšo e tla hlaha
. - Etsa tlhahlobo ea paramente e khethiloeng nakong ea ts'ebetso ea ho lekanya. Tobetsa 'me u tšoare metsotsoana e 8.6, ebe u tlohela ho khetha mokhoa oa ho lekanya. Nakong ea matla, pontšo e ka holimo e tla bontša PROG 'me pontšo e tlaase e tla bontša mofuta oa Firmware bakeng sa metsotsoana ea 6.
Menu Chate e phallang
Menu e arotsoe ka lihlopha tse 5. Ke tse latelang:
- Menu ea mosebelisi - ka tlase
- Menu ea ho seta - Leqephe la 5
- Manual Mode Menu - Leqephe la 7
- Menu ea Mokhoa oa ho Tokisoa - Leqephe la 7
- Calibration Mode Menu (ha e khothalletsoe, karolo ea calibration e tlositsoe)
Tobetsa bakeng sa parameter e latelang
Tobetsa le 
senotlolo sa ho khutlela ho parameter e fetileng.
Menyu ea mosebelisi
Lintlha tse ka tlase tsa menu ea mosebelisi lia fumaneha ho latela khetho ea mosebelisi.
Seta Menu
Lenaneo la ho seta le arotsoe ka mekhahlelo e robeli. Li thathamisitsoe ka tlaase mona.
- Basic Menu - Ka tlase
- Menu ea Liphetho)
- Menu ea Alamo
- Menu ya Kenyeho ya Ketsahalo *8. Profile Menu (Ramp le Soak)
- Mosebelisi Khetha Menu
- Lenaneo la Puisano
- Lenaneo la hona joale la Transformer
Basic Menu (bASE)
Ho menu ea ho seta, ha ponts'o e ka holimo e re "SET", Sebelisa file ea or 
linotlolo tsa ho fumana "bASE" skrineng e tlase.
Joale, sebelisa senotlolo sa ho potoloha "bASE" liparamente tsa menu./
Ha e sebetse ho molaoli o sebelisitsoeng ho khomphutha ena.
Output menu (OUT)
Ho menu ea ho seta, ha ponts'o e ka holimo e re "SET", sebelisa konopo ea or senotlolo sa ho fumana "OUT" skrineng e tlase. Ebe, sebelisa senotlolo ho potoloha liparamente tsa "OUT" tsa menu.
Manual Mode Menu - (Sebelisa bakeng sa Ts'ebetso ea Nakoana haeba Sensor e hloleha)
Tobetsa 'me u tšoare konopo ea " ” bakeng sa hoo e ka bang. 6sec ho fihlela paramethara ea "HAND" e bonts'oa skrineng e kaholimo.
Ebe, tobetsa 'me u tšoare konopo "" bakeng sa metsotsoana e meng e 5. ho fihlela "MANU" e etellang pele e qala ho benya karolong e ka tlase ea leqele la pontšo. Ebe u sebelisa konopo ea "" ho potoloha likhetho tse fumanehang.
Mosebelisi o khona ho beha tlhahiso ka letsoho hore e matlafatsoe ho tloha ho 0-100% ea nako ea potoloho.
"Hx.xx" e sebelisoa ho fetola tlhahiso ea 1.
"Cx.xx" e sebelisoa ho fetola tlhahiso ea 2.
O khona ho tsoa ka mokhoa oa matsoho ka ho tobetsa le ho tšoara 
senotlolo
Mokhoa oa ho Tokisoa ka Boiketsetso - (Fetola liparamente tsa PID ho Kopo ea Hau)
Tobetsa 'me u tšoare konopo ea " ” bakeng sa hoo e ka bang. 7sec ho fihlela paramethara ea "AT" e bonts'oa skrineng e kaholimo.
Tobetsa 'me u tšoare konopo ea " " metsotsoana e 5 ho kenya Auto-Tuning Mode. Tsoela pele ho tšoara konopo "" bakeng sa metsotsoana e meng e 3, ho seng joalo ponts'o e tla khutlela ho parameter ea "User Menu".
Tokiso ea othomathike e lumella molaoli ho fumana li-parameter tsa eona tsa optimal control (PID) ka ho metha lebelo la tšebetso ea hau ea mocheso.
Tlhaloso ea Paramente
(*Liparamente tse sa sebetseng ha li bontšoe)
| Ngolisa Aterese | Paramethara Notation | Tlhaloso ea Paramente | Range | Ea kamehla Boleng |
| 0 | SP1 | Beha Ntlha ea 1 (E sebelisetsoa Sephetho sa 1) | Tlase: SP1L
Phahameng ka ho Fetisisa: SP1H |
77.0° F |
|
8 |
INPT (Seke oa fetoha) |
Khetho ea sensor ea ho kenya |
0 J_tC: J mofuta oa Thermocouple 1 K_tC: K mofuta oa Thermocouple 2 T_tC: T mofuta oa Thermocouple
3 E_tC: E mofuta oa Thermocouple 4 B_tC: Mofuta oa B oa Thermocouple 5 R_tC: Mofuta oa R oa Thermocouple 6 S_tC: S mofuta oa Thermocouple 7 N_tC: N mofuta oa Thermocouple 8 L_tC: L mofuta oa Thermocouple 9 UTC: U thaepa Thermocouple 10 P_tC: P mofuta oa Thermocouple 11 C_tC: C mofuta oa Thermocouple 12 D_tC: D mofuta oa Thermocouple 13 Pt.dN: PT100 DIN curve 14 Pt.JS: PT100 JIS curve 15 4-20: 4-20mA linear tse kenang hona joale 16 0-20: 0-20mA linear tse kenang hona joale 17 0-5V: 0-5VDC molumo oa molumotagkenya 18 1-5V: 1-5VDC molumo oa molumotagkenya 19 0-10: 0-10VDC molumo oa molumotagkenya |
0 |
|
9 |
THUTO | Khetho ea likarolo | 0 oC:°C yuniti
1 oF:°F yuniti 2 Pu: Yuniti ea ts'ebetso |
1 |
| 10 | DP | Khetho ea lintlha tsa decimal | 0 No.dP: Ha ho ntlha ea decimal
1 1-dP: Nomoro e 1 ea decimal 2 2-dP: Nomoro e 2 ea decimal 3 3-dP: Nomoro e 3 ea decimal |
0 |
|
13 |
SP1L |
Moeli o tlase oa ntlha e behiloeng 1 (Boleng ba Span) | Tlase: -19999
Phahameng ka ho fetisisa: SP1H |
0.0° F (-18.0° C) |
|
14 |
SP1H | Moeli o phahameng oa ntlha e behiloeng 1 (Boleng ba Span) | Tlase: SP1L Holimo: 45536 | 1000.0° F
(538° C) |
| 15 | LEKHOOA | Sefe dampnako e sa fetoheng ea PV Sensor
(Sheba Leq. 14) |
0 0: 0 lekhetlo la bobeli kamehla
1 0.2: 0.2 lekhetlo la bobeli kamehla 2 0.5: 0.5 lekhetlo la bobeli kamehla 3 1: 1 lekhetlo la bobeli kamehla 4 2: 2 lekhetlo la bobeli kamehla 5 5: 5 lekhetlo la bobeli kamehla 6 10: 10 lekhetlo la bobeli kamehla 7 20: 20 lekhetlo la bobeli kamehla 8 30: 30 lekhetlo la bobeli kamehla 9 60: 60 lekhetlo la bobeli kamehla |
2 |
(*Liparamente tse sa sebetseng ha li bontšoe)
| Ngolisa Aterese | Paramethara Notation | Tlhaloso ea Paramente | Range | Ea kamehla Boleng |
| 16 | TLHOKOMELA | Khetho ea bobeli ea pontšo | 0 Ha ho letho: Ha ho Pontšo 1 MV1: Hlahisa MV1 2 MV2: Hlahisa MV2
3 TIMR: Bontša Nako ea ho Lula 4 PROF: bonts'a Profile Boemo |
0 |
| 17 | PB | Proportional band value
(Sheba Leq. 17) |
Ka tlase: 0.0
Holimo: 500.0°C (900.0°F) |
18.0° F
(10.0° C) |
|
18 |
TI |
Nako ea bohlokoa ea nako
(Sheba Leq. 17) |
Ka tlase: 0 Holimo: 3600 sec |
100 |
| 19 | TD | Theko ea nako e tsoang ho eona (Sheba Leq. 17) |
Ka tlase: 0.0 |
25 |
| 20 | KHAOLO1 | Sephetho sa 1 tshebetso |
0 REVR: Ketso ea ho laola (ho futhumatsa) ka morao 1 TSHOLA : Ketso e tobileng (e pholileng) ea taolo |
0 |
| 21 | O1TY FACTORY SET, U SE KE UA FETOHA |
Mofuta oa 1 oa tlhahiso |
0 TŠEPANG: Tlhahiso ea relay
1 SSrd: Tlhahiso ea boemo bo tiileng ba relay drive 2 4-20: 4-20mA linear hona joale 3 0-20: 0-20mA linear hona joale 4 0-5V: 0-5VDC molumo oa molumotage 5 1-5V: 1-5VDC molumo oa molumotage 6 0-10: 0-10VDC molumo oa molumotage |
1 |
|
22 |
O1FT | Mokhoa oa phetiso ea ho hloleha ha 1
(Sheba Leq. 15) |
Khetha BPLS (Bumpless transfer), kapa 0.0 ~ 100.0 % ho tsoelapele ka ts'ebetso ea taolo ea 1 haeba sensor e hloleha, kapa khetha OFF (0) kapa ON (1) bakeng sa taolo ea ON-OFF |
0 |
| 23 | O1HY | Sephetho sa 1 ON-OFF laola hysteresis. PB=0 |
Tlase: 0.1°C (0.2°F) Holimo: 50.0°C (90.0°F) |
0.2° F (0.1° C) |
| 24 | CYC1 | Nako ea ho tsoa 1 ea potoloho | Ka tlase: 0.1
Phahameng: 90.0 sec. |
1.0 |
| 26 | RAMP | Ramp khetho ea mosebetsi
(Sheba Leq. 13) |
0 HA HO MOTHO: Ha ho Ramp Mosebetsi
1 MINR: Sebelisa °/metsotso joalo ka Ramp Sekhahla 2 HRR: Sebelisa °/hora joalo ka Ramp Sekhahla |
0 |
(*Liparamente tse sa sebetseng ha li bontšoe)
| Ngolisa Aterese | Paramethara Notation | Tlhaloso ea Paramente | Range | Ea kamehla Boleng |
| 27 | RR | Ramp sekhahla
(Sheba Leq. 13) |
Tlase: 0.0 Holimo: 900.0°F | 0 |
|
61 |
PL1L | Output 1 Moedi o tlase oa Matla | Ka tlase: 0
Holimo:PL1H kapa 50% |
0 |
| 62 | PL1H | Output 1 High Power limit | Tlase: PL1L
Holimo: 100% |
100 |
| 94 | PHASA | Keno ea phasewete
(Sheba Leqephe le Latelang) |
Ka tlase: 0
Phahameng ka ho Fetisisa: 9999 |
0 |
Lenaneo
Tobetsa o hatelle metsotsoana e 5, ebe o lokolla ho kenya menu ea ho seta. Tobetsa o lokolle ho potoloha lethathamong la liparamente. Pontšo e ka holimo e bontša letšoao la parameter, 'me pontšo e tlaase e bontša boleng ba parameter e khethiloeng.
Tshireletso ya mosebedisi
Ho na le liparamente tse peli, PASS (password) le CODE (khoutu ea tšireletso), e tla laola lenaneo la ho notlela.
| CODE Boleng | PASS Boleng | Litokelo tsa ho fihlella |
| 0 | Boleng bofe kapa bofe | Li-parameter tsohle lia fetoha |
| 1000 | =1000 | Li-parameter tsohle lia fetoha |
| ≠1000 | Ke li-parameter tsa menyetla ea basebelisi feela tse ka fetoloang | |
| 9999 | =9999 | Li-parameter tsohle lia fetoha |
| ≠9999 | Ke SP1 ho ea ho SP7 feela e fetohang | |
| Ba bang | =KHOUTU | Li-parameter tsohle lia fetoha |
| ≠CODE | Ha ho li-parameter tse ka fetoloang |
Keletso ea Pontšo
INPT: Feme e behiloe ho ngola "J" thermocouple.
SE FETOHENG
UNIT: Khetha yuniti ea ts'ebetso eo u e batlang
Likhetho: °C, °F.
DP: Khetha qeto e lakatsehang (lintlha tsa decimal) bakeng sa boleng ba ts'ebetso.
Laola Sephetho
Ho na le mefuta ea 4 ea mekhoa ea taolo e ka hlophisoang joalo ka ha ho bonts'itsoe ka tlase.
Mocheso Feela ON-OFF Taolo - (E sebelisoa bakeng sa Solonoids le Li-valve)
Kgetha REVR bakeng sa OUT1, Seta PB ho 0. O1HY e sebediswa ho lokisa hysteresis bakeng sa taolo ya ON-OFF. Tlhahiso ea 1 hysteresis (O1HY) setting e fumaneha feela ha PB = 0. Mocheso feela ON-OFF mosebetsi oa ho laola o bontšitsoe ka tlase.
Taolo ea ON-OFF e ka baka ts'ebetso e feteletseng ea oscillations le haeba hysteresis e behiloe ho boleng bo bonyenyane ka ho fetisisa.
Haeba taolo ea ON-OFF e sebelisoa (ke hore, PB = 0), TI, TD, CYC1, OFST, CYC2, CPB, DB ha e sa tla hlola e sebetsa 'me e tla patoa. Mokhoa oa Auto-Tuning le phetisetso ea Bumpless ha e khonehe ka mokhoa oa ho tima / ho tima.
Chesa feela P kapa PD Control - (E sebelisoa bakeng sa Heater ea Motlakase
Khetha REVR bakeng sa OUT1, beha TI = 0, OFST e sebelisetsoa ho fetola taolo ea taolo (ho seta ka letsoho). Haeba PB ≠0 joale O1HY e tla patoa.
Mosebetsi oa OFST: OFST e lekantsoe ka % ka mefuta e fapaneng ea 0 - 100.0 %. Ha ts'ebetso e tsitsitse, ha re re boleng ba ts'ebetso bo tlase ho feta sebaka se behiloeng ka 5 ° F. Hape ha re re 20.0 e sebelisoa bakeng sa maemo a PB. Ho sena mohlalaample, 5°F ke 25% ya sehlopha sa proportional (PB).
Ka ho eketsa boleng ba OFST ka 25%, tlhahiso ea taolo e tla itlhophisa, 'me boleng ba ts'ebetso bo tla qetella bo lumellana le ntlha e behiloeng.
Ha u sebelisa taolo ea Proportional (P) (TI = 0), Auto-Tuning e ke ke ea fumaneha. Sheba karolo ea "tuning ka letsoho" bakeng sa tokiso ea PB le TD. Ho tsosolosa ka letsoho (OFST) hangata ha ho sebetse hobane mojaro o ka fetoha nako le nako; ho bolelang hore boemo ba OFST bo tla hloka ho lula bo lokisoa. Taolo ea PID e ka qoba bothata bona.
Taolo ea PID ea ho futhumatsa feela - (Mohloli oa Licheso tsa Motlakase)
Khetha REVR bakeng sa OUT1. PB le TI ha lia lokela ho ba zero. Etsa Tokiso ea Auto bakeng sa ho qala. Haeba sephetho sa taolo se sa khotsofatse, sebelisa tokiso ea matsoho kapa u leke Auto-Tuning lekhetlo la bobeli ho ntlafatsa tšebetso ea taolo.
Pholisa feela Taolo
Taolo ea ON-OFF, Taolo e lekanang, le taolo ea PID e ka sebelisoa bakeng sa taolo ea ho pholisa. Beha "OUT1" ho DIRT (ketso e tobileng).
HLOKOMELA: Taolo ea ON-OFF e ka baka ho thunya ho feteletseng le ho fokotseha ho hoholo ts'ebetsong. Taolo e leka-lekaneng e ka fella ka ho kheloha ha boleng ba ts'ebetso ho tloha sebakeng se behiloeng. Ho khothalletsoa ho sebelisa taolo ea PID bakeng sa taolo ea ho futhumatsa kapa ho futhumatsa ho hlahisa boleng bo tsitsitseng ba ts'ebetso.
Ha u khetha li-parameter, likarolo tsohle tse ka holimo li ka 'na tsa se ke tsa fumaneha. Palo ea li-parameter tse bonahalang e itšetlehile ka tlhophiso ea molaoli.
Ramp
The rampts'ebetso ea ho kenya e etsoa nakong ea ho phahamisa matla kapa nako efe kapa efe sebaka se behiloeng se fetoloang. Khetha "MINR" (ramp ka metsotso) kapa "HRR" (ramp ka lihora) bakeng sa "RAMP” setting, mme molaoli o tla etsa rampmosebetsi oa ho. The ramp rate e hlophisoa ka ho fetola "RR" setting. The ramping e ea tingoa neng kapa neng ha molaoli a kena Mokhoeng oa Ho hloleha, Mokhoa oa ho laola ka letsoho, Mokhoa oa Auto-Tuning kapa Mokhoa oa Calibration.
Rampka Example ntle le Lula Nako
Beha "RAMP” ho beha “MINR” ho ramp ka metsotso.
Beha ramp sekhahla (RR) ho isa ho 10.
Mocheso oa ho qala ke 30°C.
Setulo sa pele se behiloe ho 200 ° C.
Kamora hore ts'ebetso e futhumale, mosebelisi o ile a fetola sebaka sa ho bea ho 100 ° C kamora metsotso e 30.
Ka mor'a hore motlakase o phahamisoe, ts'ebetso e tla sebetsa joalokaha ho bontšitsoe ka tlase.
Hlokomela: Ha ramp ts'ebetso e sebelisoa, ponts'o e tlase e tla bonts'a r ea hajoaleamping value. Leha ho le joalo, e tla khutlela ho bonts'a boleng ba ntlha e behiloeng hang ha senotlolo sa holimo kapa sa tlase se angoa bakeng sa tokiso. The ramp rate e qalisoa ka matla ka le/kapa neng kapa neng ha Set point e fetoloa. Ho beha boemo ba "RR" ho zero ho bolela hore ha ho rampts'ebetso ea ing e sebelisoa.
Khalo ea mosebelisi - Pontšo ea Offset
Karolo ka 'ngoe e lekantsoe fekthering pele e romelloa. Mosebedisi o ntse a ka fetola tlhophiso sebakeng.
Tekanyo ea mantlha ea molaoli e tsitsitse haholo 'me e etselitsoe bophelo bohle. Tekanyetso ea mosebelisi e lumella mosebelisi ho fokotsa tekano ea feme e sa feleng e le hore:
- Beakanya molaoli ho fihlela litekanyetso tsa litšupiso tsa mosebelisi.
- Bapisa tekanyo ea molaoli le ea transducer e itseng kapa keno ea kutlo.
- Lekanya molaoli ho lumellana le litšobotsi tsa ts'ebetso e itseng.
- Tlosa ho hoholeha ha nako e telele ka har'a sete ea feme.
Ho na le liparamente tse peli: Offset Low (OFTL) le Offset High (OFTH) bakeng sa tokiso ho lokisa phoso boleng ba ts'ebetso.
Ho na le li-parameter tse peli bakeng sa ho kenya sensor. Lintlha tsena tse peli tsa matšoao ke CALO le CAHI. Letšoao la ho kenya litekanyo tse tlaase le tse phahameng li lokela ho kenngoa ho li-parameter tsa CALO le CAHI ka ho latellana.
Sheba karolo ea 1.6 bakeng sa ts'ebetso ea bohlokoa le karolo ea 1.7 bakeng sa "flowchart" ea ts'ebetso. Tobetsa o hatelle konopo ho fihlela leqephe la Menu ea ho seta le fumanoa. Ebe, tobetsa le ho lokolla faele ea senotlolo sa ho ea ho paramethara e tlase ea tekanyo OFTL. Romela lets'oao la hau le tlase ho sensara se kenang ho molaoli, ebe o tobetsa le ho lokolla senotlolo. Haeba boleng ba ts'ebetso (pontšo e ka holimo) bo fapane le letšoao la ho kenya, mosebedisi a ka sebelisa le linotlolo ho fetola boleng ba OFTL (pontšo e tlaase) ho fihlela boleng ba ts'ebetso bo lekana le boleng boo mosebedisi a bo hlokang. Tobetsa le tšoara senotlolo bakeng sa metsotsoana e 5 ho phethela tekanyo ea lintlha tse tlase (ponts'o e lokela ho panya hang). Mokhoa o ts'oanang o sebelisoa bakeng sa tekanyo e phahameng ea tekanyo.
Joalokaha ho bontšitsoe ka tlase, lintlha tse peli OFTL le OFTH li etsa mola o otlolohileng. Bakeng sa morero oa ho nepahala, ho molemo ho lekanyetsa lintlha tse peli tse arohaneng ka hohle kamoo ho ka khonehang. Kamora hore tlhahlobo ea mosebelisi e phetheloe, mofuta oa ho kenya o tla bolokoa mohopolong. Haeba mofuta oa ho kenya o fetotsoe, ho tla ba le phoso ea ho lekanya le khoutu ea phoso 
e bontshwa.
Filter ea Digital
Lits'ebetsong tse ling boleng ba ts'ebetso ha bo tsitsitse haholo hore bo ka baloa. Ho ntlafatsa sena, ho ka sebelisoa filthara ea "low pass" e hlophisitsoeng e kentsoeng ho molaoli. Ena ke sefe ea pele e nang le nako e behiloeng ke paramethara ea FILT. Boleng ba metsotsoana e 0.5 bo sebelisoa e le feme ea kamehla. Fetola FILT ho fetola nako ho tloha ho 0 ho isa ho metsotsoana e 60. Metsotsoana e 0 ha e bontše hore ha ho sefe se sebelisoang lets'oao la ho kenya.
Sesefe se tšoauoa ka setšoantšo se latelang.
Hlokomela: Filter e fumaneha feela bakeng sa boleng ba ts'ebetso (PV), 'me e etsoa bakeng sa boleng bo bontšitsoeng feela.
Molaoli o etselitsoe ho sebelisa lets'oao le sa sefshoang bakeng sa taolo leha sefahla se sebelisoa. Haeba lets'oao le saletseng morao (le tlhotliloeng) le sebelisoa bakeng sa taolo; e ka hlahisa ts'ebetso e sa tsitsang.
Ho hloleha Phetisetso
Mookameli o tla kenya mokhoa oa ho hlōleha haeba e 'ngoe ea maemo a latelang e etsahala:
- Phoso ea SBER e etsahala ka lebaka la khefu ea sensor ea ho kenya, hona joale ho kenya ka tlase ho 1mA bakeng sa 4-20mA, kapa phallo ea motlakase.tage ka tlase ho 0.25V bakeng sa 1-5 V.
- Phoso ea ADER e etsahala ka lebaka la ho hloleha ho fetolela AD.
Output 1 le Output 2 tla etsa hloleha ho fetisa (O1.ft & O2.ft) mosebetsi ha molaoli a kena ka mokhoa oa ho hlōleha.
Output 1 Ho hloleha Phetiso
Haeba Output 1 Failure Transfer e kentswe tshebetsong, e tla sebetsa ka tsela e latelang:
- Haeba tlhahiso ea 1 e hlophisitsoe e le taolo e lekanang (PB≠0), 'me BPLS e khethetsoe O1FT, joale tlhahiso ea 1 e tla etsa phetiso ea Bumpless. Ka mor'a moo, boleng bo fetileng ba boleng ba tlhahiso bo tla sebelisoa ho laola tlhahiso ea 1.
- Haeba tlhahiso ea 1 e hlophisitsoe e le taolo e lekanang (PB≠0), 'me boleng ba 0 ho 100.0 % bo behiloe bakeng sa O1FT, joale tlhahiso ea 1 e tla etsa phetiso ea ho hlōleha. Ka mor'a moo boleng ba O1FT bo tla sebelisoa ho laola tlhahiso ea 1.
- Haeba tlhahiso ea 1 e hlophisitsoe e le taolo ea ON-OFF (PB=0), joale tlhahiso ea 1 e tla fetela sebakeng sa ho tima haeba OFF e setetsoe O1FT, kapa e tla fetisetsa ho boemo haeba ON e setetsoe O1FT.
Ho itokisa ka boithaopo
Ts'ebetso ea Auto-Tuning e tla etsoa sebakeng se behiloeng (SP1). Ts'ebetso e tla potoloha sebakeng se behiloeng nakong ea ts'ebetso ea tokiso. Beha ntlha e behiloeng ho boleng bo tlase haeba ho thunngoa ho feta tekanyo e tloaelehileng ea ts'ebetso ho tla baka tšenyo. Hangata ho molemo ho etsa Auto-Tuning sebakeng sa Sete seo mochini o lebelletsoeng ho sebetsoa ho sona, 'me ts'ebetso e sebetsa ka mokhoa o tloaelehileng (ke hore thepa e ka ontong, jj.)
Auto-Tuning hangata e sebelisoa maemong a latelang:
- Phetolelo ea pele bakeng sa ts'ebetso e ncha
- Sebaka se behiloeng se fetotsoe haholo ho tloha sebakeng se fetileng sa Setha ha Auto-Tuning e ne e etsoa.
- Sephetho sa taolo ha se khotsofatse
Mehato ea Ts'ebetso ea Auto-Tokiso
- Sistimi e etselitsoe ho sebetsa tlasa maemo a nnete a lefats'e.
- Litlhophiso tsa "PB le "TI" ha lia lokela ho hlophisoa ho zero.
- LOCK parameter e lokela ho hlophisoa ho NONE.
- Beha sebaka se behiloeng ho boleng bo tloaelehileng ba ts'ebetso, kapa boleng bo tlaase haeba ho fetela holimo ho feta tekanyo e tloaelehileng ea ts'ebetso ho tla baka tšenyo.
- Tobetsa 'me u tšoare senotlolo ho fihlela se hlaha skrineng e ka holimo. Tsoela pele ho tšoara konopo "" bakeng sa metsotsoana e meng e 3, ho seng joalo ponts'o e tla khutlela ho parameter ea "User Menu".
- Tobetsa 'me u tšoare senotlolo ho fihlela letšoao la TUNE le qala ho benya.
- Ts'ebetso ea Auto-Tuning e se e qalile.
HLOKOMELA:
Nakong ea Auto-Tuning, tlhahiso e tla lula e ntse e tsoela pele ho fihlela Boleng ba Ts'ebetso bo fihla moo ho behiloeng. Sena se ka 'na sa etsa hore mocheso o fete sebaka se behiloeng.
Joale, tlhahiso e tla lula e tima ho fihlela boleng ba ts'ebetso bo oela ka tlase ho setpoint.
Sena se tla etsahala bonyane makhetlo a mabeli ha molaoli a ntse a "ithuta" mokhoa oa ho laola ts'ebetso ea hau.
Mekhoa
Auto-Tuning e ka sebelisoa ha ts'ebetso e ntse e futhumala (Cold Start) kapa ha ts'ebetso e ntse e tsitsitse (Mofuthu oa ho Qala). Ka mor'a hore ts'ebetso ea Auto-Tuning e phethoe, letšoao la TUNE le tla khaotsa ho khantša 'me yuniti e tla khutlela taolong ea PID ka ho sebelisa litekanyetso tsa eona tse ncha tsa PID. Litekanyetso tsa PID tse fumanoeng li bolokiloe mohopolong o sa fetoheng.
Phoso ea ho Tokisoa
Haeba Auto-Tuning e hloleha, ATER 
molaetsa o tla hlaha skrineng e kaholimo maemong afe kapa afe a latelang.
- Haeba PB e feta 9000 (9000 PU, 900.0°F kapa 500.0°C)
- Haeba TI e feta metsotsoana e 1000
- Haeba sebaka se behiloeng se fetoloa nakong ea ts'ebetso ea Auto-Tuning
Tharollo bakeng sa Phoso ea ho Tokisoa ha Auto
- Leka ho Tokisoa hape.
- Qoba ho fetola boleng ba ntlha nakong ea ts'ebetso ea Auto-Tuning.
- Netefatsa hore PB le TI ha lia behoa ho zero.
- Sebelisa tokiso ea matsoho.
- Tobetsa RESET senotlolo sa ho reset the molaetsa.
Tokiso ea letsoho
Lits'ebetsong tse ling, ho sebelisa Auto-Tuning ho kanna ha se lekane bakeng sa tlhoko ea taolo, kapa, ts'ebetso e tsamaea butle haholo ho Auto-Tuning ka nepo.
Haeba ho joalo, mosebelisi a ka leka ho hlophisa ka letsoho.
Haeba ts'ebetso ea taolo ka ho sebelisa Auto-Tuning e ntse e sa khotsofatse, ho ka sebelisoa litataiso tse latelang bakeng sa tokiso e eketsehileng ea boleng ba PID.
| TS'ELISO TS'ELISO | PONTS'O LEKHOTLA | THABELO |
| Sehlopha sa Proportional ( PB ) | Karabelo e Butle | Fokotsa PB |
| High overshoot kapa Oscillations | Eketsa PB | |
| Nako e Kopanetsoeng ( TI ) | Karabelo e Butle | Fokotsa TI |
| Ho hloka botsitso kapa ho sisinyeha | Eketsa TI | |
| Nako e Ncha (TD) | Karabelo e butle kapa ho nyenyefatsa | Fokotsa TD |
| High Overshoot | Eketsa TD |
2-2.PID Tataiso ea Phetoho ea Parameter
Taolo ka letsoho
Ho nolofalletsa taolo ea letsoho, etsa bonnete ba hore paramethara ea LOCK e behiloe ho NONE.
Tobetsa o hatelle ho fihlela 
(Hand Control) e hlaha skrineng. Tobetsa 'me u tšoare ho fihlela letšoao la "MANU" le qala ho benya. Pontšo e tlase e tla hlaha 
.
E bonts'a phapang ea taolo ea tlhahiso bakeng sa tlhahiso ea 1, le 
e bonts'a phapang ea taolo bakeng sa tlhahiso ea 2. Mosebedisi a ka sebedisa dikonopo tse hodimo-tlase ho lokisa peresentetagboleng ba ho futhumatsa kapa ho pholisa. Boleng bona ba % bo ipapisitse le litlhophiso tsa CYC1 le CYC2, moo tlhahiso e amanang le eona e tla lula e le teng bakeng sa % ea nako eo litekanyetso tsa CYC1 & CYC2 li behiloeng bakeng sa eona.
Example: Haeba CYC1 e behiloe ho 20seconds, 'me molaoli o behiloe ho "H50.0", tlhahiso e tla buloa bakeng sa 10seconds, ebe e tima metsotsoana e 10.
Mookameli o etsa taolo e bulehileng ea loop mme o hlokomoloha sensor ea ho kenya hafeela e ntse e lula ka mokhoa oa ho laola litaelo
Tsoa ho Taolo ea Matsoho
Ho hatella senotlolo se tla khutlisetsa molaoli ho mokhoa oa eona o tloaelehileng oa pontšo.
Ho beha Molaoli ho Fektheri ea kamehla
Litekanyetso tsa molaoli li ka laeloa ka boleng ba kamehla bo thathamisitsoeng tafoleng ea tlhaloso ea parametha . Boemong bo itseng ke ho lakatsehang ho boloka litekanyetso tsena ka mor'a hore litekanyetso tsa parameter li fetoloe. Mokhoa o ka tlase o lokelang ho lateloa ho kenya bocha boleng ba kamehla.
- Netefatsa hore LOCK parameter e behiloe ho NONE.
- Tobetsa o hatelle ho fihlela (Hand Control) e hlaha skrineng.
- Tobetsa 'me u lokolle senotlolo ho potoloha menu ea mokhoa oa matsoho ho fihlela "FILE”.
- Tobetsa 'me u tšoare metsotsoana e 5 kapa ho fihlela pontšo e ka holimo FILE kganya nakwana.
Tlhaloso ea khoutu ea Phoso e hlalositsoe ka tlase
| Khoutu ea Phoso | Letšoao la Pontšo | Tlhaloso & Lebaka | Ketso ea ho Lokisa |
|
4 |
ER04 |
Ho sebelisitsoe litekanyetso tse seng molaong: COOL e sebelisoa bakeng sa OUT2 ha DIRT (ketso ea ho pholisa) e sebelisetsoa OUT1, kapa ha mokhoa oa PID o sa sebelisoe bakeng sa OUT1 (PB =0 le/kapa TI=0) |
Sheba le ho lokisa litekanyetso tsa ho seta tsa OUT2, PB1, PB2, TI1, TI2 le OUT1. HAEBA OUT2 e hlokahala bakeng sa taolo ea ho pholisa, molaoli o lokela ho sebelisa mokhoa oa PID (PB≠ 0 le TI≠ 0) le OUT1 e lokela ho sebelisa mokhoa o ka morao (ketso ea ho futhumatsa), ho seng joalo, OUT2 e ke ke ea sebelisoa bakeng sa taolo ea ho pholisa. |
|
10 |
ER10 |
Phoso ea puisano: khoutu ea ts'ebetso e mpe | Lokisa software ea puisano ho fihlela litlhoko tsa protocol. |
| 11 | ER11 | Phoso ea puisano: ngodisa aterese ha e felle moo | Se ke oa fana ka aterese e fetang tekano ea rejisetara ho ea ho ea bobeli |
| 14 | ER14 | Phoso ea puisano: leka ho ngola lintlha tse baloang feela | Se ke oa ngola lintlha tsa ho bala feela kapa data e sirelelitsoeng ho ea bobeli. |
|
15 |
ER15 |
Phoso ea puisano: ngola boleng e leng
ho tsoa ho rejisetara |
Se ke oa ngola lintlha tse ngata ho rejisetara ea bobeli |
| 16 | EIER | Phoso ea Kenyeletso ea Ketsahalo: Kenyelletso ea liketsahalo tse peli kapa ho feta li behiloe tšebetsong e tšoanang | Se ke oa beha tšebetso e ts'oanang liparamenteng tse peli kapa ho feta tsa Ketsahalo ea Kenyeletso ea Ketsahalo (E1FN ho isa E6FN) |
| 26 | MOTSOALLE | Phoso ea ho Itokisa: E hlolehile ho etsa mosebetsi oa Auto-Tuning |
1. Litekanyetso tsa PID tse fumanoeng ka mor'a ts'ebetso ea Auto-Tuning li tsoile sebakeng. Leka hape ho Tokisoa. 2. Se ke oa fetola boleng ba setpoint nakong ea ts'ebetso ea Auto- Tuning. 3. Sebelisa tokiso ea matsoho ho e-na le mokhoa oa Auto-Tuning. 4. U se ke ua beha boleng ba lefela bakeng sa TI. 5. Se ke oa beha boleng ba lefela bakeng sa PB. 6. Tobetsa konopo ea RESET |
| 29 | EEPR | EEPROM ha e khone ho ngoloa ka nepo | Khutlela femeng ho ea lokisoa. |
| 30 | CJER | Matšeliso a matekoane a batang bakeng sa ho se sebetse hantle ha Thermocouple | Khutlela femeng ho ea lokisoa. |
| 39 | SBER | Ho robeha ha sensor ea ho kenya, kapa hona joale ho kenya ka tlase ho 1 mA haeba ho sebelisoa 4-20 mA, kapa ho kenya matlatage ka tlase
0.25V haeba 1 - 5V e sebelisoa |
Tlosa sensor ea ho kenya sebaka. |
| 40 | ADER | Sefetoleli sa A ho ea ho D kapa ho se sebetse hantle ha likaroloana tse amanang | Khutlela femeng ho ea lokisoa. |
6.5 Mokhoa
Boleng ba Rejistara ea Mokhoa bo joalo ka tlase.
| Boleng | Mokhoa |
| H'000X | Mokhoa o tloaelehileng |
| H'010X | Mokhoa oa ho lekanya |
| H'020X | Mokhoa oa ho lokisa ka boiketsetso |
| H'030X | Mokhoa oa ho laola ka letsoho |
| H'040X | Mokhoa oa ho hloleha |
| H'0X00 | Boemo ba alamo bo timiloe |
| H'0x01 | Boemo ba alamo bo butswe |
6-6.Mokhoa oa Ts'ebetso
PUSELETSO
Ha ho lihlahisoa tsa lihlahisoa tse ka amoheloang ntle le Return e phethiloeng
Foromo ea tumello ea lintho tse bonahalang (RMA).
TŠEHETSO EA TEKHENIKI
Lipotso tsa tekheniki le thuso ea ho rarolla mathata li fumaneha ho tsoa ho
Tempco. Ha o letsa kapa o ngola ka kopo fana ka lintlha tse ngata
tlhahisoleseding mabapi le kopo kapa tshebetso ka moo ho ka kgonehang.
E-mail: techsupport@tempco.com
Mohala: 630-350-2252
800-323-6859
Hlokomela: Lintlha tse bukeng ena li nkuoe li nepahetse nakong ea khatiso.
Leano la Tempco ke e 'ngoe ea ntlafatso e tsoelang pele le ntlafatso ea lihlahisoa, 'me re na le tokelo ea ho fetola litlhaloso le meralo ntle le tsebiso pele. Ha e ikarabelle bakeng sa liphoso tsa typographical.
Custom Manufacture Ho tloha 1972
LITLHAKISO TSA MOTLATSI OA MOTLATSI • LITOLAOLI TSA MOCHESO • LITŠOANTŠISO • TŠEBELETSO TSA MEFUTA
CHESETSA LINTHO!
Ka Liketekete tsa Mefuta-futa ea Liqapi Re Etsa Tsohle Seo U se Hlokang.
Li-heaters tsa lihlopha
Li-heaters tsa ho futhumatsa
Li-heaters tse khanyang
Li-heaters tse feto-fetohang
Lisebelisoa tsa ho futhumatsa
Taolo ea Mocheso
Li-heaters tsa Cartridge
Li-heaters tsa Coil & Cable
Li-heaters tsa hlobo
Li-heaters tsa Tubular
Lisebelisoa
Li-Sensors tsa Mocheso
607 N. Central Avenue Wood Dale, IL 60191-1452 USA
P: 630-350-2252 Mahala: 800-323-6859
F: 630-350-0232 E: info@tempco.com
www.tempco.com
© Copyright 2022 TEHC. Litokelo tsohle li sirelelitsoe
Litokomane / Lisebelisoa
 |
Tempco TPC40034 Power Control Console [pdf] Bukana ea Mosebelisi TPC40034 Power Control Console, Power Control Console, Control Console, TPC40035 |
