TCP ISREMOTE Remote Control
Litlhaloso tsa Sehlahisoa
- Lebitso: TCP
- Sehlahisoa: Taolo ea Remote
- Model: ISREMOTE
- Works with any IS Motion Sensor
- Customization of luminaires
The TCP IS Remote works with any IS Motion Sensor to allow easy customization of any of your luminaires.
Remote Usage Instructions
Khanya ea LED
Set the brightness level when occupancy is sensed and luminaire is switched on.
Kutloelo-bohloko
Adjust the occupancy sensing sensitivity of the sensor.
Tšoara Nako
Set the duration the sensor remains at full brightness before turning off or entering standby mode.
Sensor ea Motšehare
Preset threshold levels for the daylight sensing functions.
*In applicable sensors only
Standby Dim
Adjust the lux value to act as the daylight threshold. This feature enables daylight sensor functionality in all applications. (Only applicable in certain sensors)
Nako ea ho ema
To set the bi-level dimming after the initial hold time. Setting standby dim level at 0% means the device will turn off after the initial hold time (Standard mode). Setting standby dim level to the other provided options will place the device in bi-level mode.
Set the current lux value as the daylight threshold. This feature enables the daylight sensor to function in all applications.
*In applicable sensors only
The daylight sensor is turned off and the sensor functions in standard or bi-level dimming mode.
ON/OFF Konopo
Press the ON/OFF button, the light goes to permanent on or permanent off mode, and the sensor is disabled (Must press the AUTO button to quit this mode for setting).
Display the current/latest setting parameters in LED indicators (the LED indicators will turn on for showing the setting parameters).
TSOHLE Konopo
Press RESET button, all settings go back the settings of the dip switch in sensor.
KHETHA Konopo
Select active parameter for editing after pressing DISP. The selected function will flash.
OK Konopo
Select OK to save the selected settings to the remote.
Settings will be saved to the remote but will still need sent to the device
SEND Button
Press the SEND button to upload the current settings to the fixture (Press DISP to see current settings.) The fixture will flash on/off to confirm the settings have been received.
Mefuta e 4 ea liketsahalo tse nang le li-parameter tse seng li setiloe tse fumanehang hore li ka fetoloa le ho bolokoa ka mekhoa.
Konopo ea AUTO
Press AUTO button, the sensor starts to function and all settings remain the same as the latest status before the light is switched on/off.
TEST 2s Button
The button TEST 2s is for testing purpose sensitivity only after you choose sensitivity thresholds, then you press the TEST 2s button.
The sensor goes to test mode (hold time is only 2s) automatically, meanwhile the standby period and daylight sensor are disabled. Press AUTO button to quit from this mode.
LEFT/RIGHT Buttons
Navigate to LEFT and RIGHT to choose between options of the selected parameters in LED indicators
Likonopo tse PHAHAMANG/ TLASE
Open and close smart daylight sensor. Press UP or DOWN, enter in the setting condition, the parameter LEDs of remote control will flash to be selected, press this button to open or close smart daylight sensor.
*In applicable sensors only
THEKNOLOJI E HLAHALA KA LESEDI LE LINTLE
Ka lilemo tse fetang 30, TCP esale e rala, e nts'etsapele le ho fana ka mabone a baballang matla 'marakeng. Ka lebaka la theknoloji ea rona ea morao-rao le boitseanape ba tlhahiso, re rometse libilione tsa lihlahisoa tsa boleng bo holimo tsa mabone. Ka TCP, u ka itšetleha ka sehlahisoa sa mabone se etselitsoeng ho finyella litlhoko tsa 'maraka - se fetolang tikoloho ea hau le ho u koahela ka mofuthu - mabone a hlahisang botle ka flip e' ngoe le e 'ngoe ea switjha.
Bakeng sa boitsebiso bo eketsehileng mabapi le boleng le tlhokomelo ea TCP e ka fanang ka eona, re letsetse ho 800.324.1496 kapa u etele tcpi.com
325Camprona Dr. | Aurora, Ohio 44202 | P: 800.324.1496 | F: 877.487.0516
Lipotso Tse Botsoang Hangata
Q: How do I know if my sensor is compatible with the TCP IS Remote?
A: The TCP IS Remote works with any IS Motion Sensor, ensuring compatibility for customization of luminaires.
Q: Can I adjust the daylight sensing functionality of my luminaire?
A: Yes, you can set threshold levels and adjust the sensitivity of the daylight sensor in applicable sensors.
Litokomane / Lisebelisoa
 |
TCP ISREMOTE Remote Control [pdf] Buka ea Taelo ISREMOTE, ISREMOTE Remote Control, ISREMOTE, Remote Control, Control |