SYSTEM SENSOR PDRP-1001 Meroallo Preaction Control Panel Tataiso ea Mosebelisi

Tlhokomelo ea ho Hloma - Ho latela tse latelang ho tla thusa ho kenya ts'ebetso e se nang mathata ka ts'epo ea nako e telele:

TLHOKOMELO - Mehloli e mengata e fapaneng ea matla e ka hokahanngoa le phanele ea taolo ea alamo ea mollo. Hlakola mehloli eohle ea matla pele u sebeletsa. Setsi sa taolo le lisebelisoa tse amanang le tsona li ka senyeha ka ho ntša le/kapa ho kenya likarete, li-module, kapa likhoele tse hokelang ha yuniti e ntse e matlafatsoa. Se ke oa leka ho kenya, ho sebeletsa, kapa ho sebelisa yuniti ena ho fihlela bukana ena e baloa le ho utloisisoa.

TLHOKOMELO - Teko ea Kamohelo ea Sistimi ka mor'a Liphetoho tsa Software: Ho netefatsa ts'ebetso e nepahetseng ea sistimi, sehlahisoa sena se tlameha ho lekoa ho latela NFPA 72-1993 Khaolo ea 7 kamora ts'ebetso efe kapa efe ea lenaneo kapa phetoho ea software e ikhethileng ea sebaka. Teko ea ho amohela hape e ea hlokahala kamora phetoho efe kapa efe, ho eketsoa kapa ho hlakoloa ha likarolo tsa sistimi, kapa kamora phetoho efe kapa efe, tokiso kapa tokiso ea lisebelisoa tsa sistimi kapa terata.

Likarolo tsohle, lipotoloho, ts'ebetso ea sistimi kapa mesebetsi ea software e tsejoang hore e angoa ke phetoho e tlameha ho lekoa ka 100%. Ho feta moo, ho etsa bonnete ba hore lits'ebetso tse ling ha li amehe ka boomo, bonyane 10% ea lisebelisoa tse qalang tse sa angoeng ke phetoho ka kotloloho, lisebelisoa tse fihlang ho tse 50 le tsona li tlameha ho lekoa le ho netefatsoa ts'ebetso ea sistimi e nepahetseng.

Tsamaiso ena e fihlela litlhoko tsa NFPA bakeng sa ts'ebetso ho 0-49^O C/ 32-120^O F le mongobo o lekanyelitsoeng oa 85% RH (e sa nyenyefatseng) ho 30^O C/86^O F. Leha ho le joalo, bophelo ba tšebeliso ea libeteri tse emeng tsa sistimi le likarolo tsa elektroniki li ka angoa hampe ke mefuta e feteletseng ea mocheso le mongobo. Ka hona, ho kgothaletswa hore tsamaiso ena le lisebelisoa tsa eona li kenngoe sebakeng se nang le mocheso oa kamore ea 15-27.^O C/60-80^O F.

Netefatsa hore boholo ba terata bo lekane bakeng sa lisebelisoa tsohle tse qalang. Lisebelisoa tse ngata ha li khone ho mamella ho theoha ho fetang 10% IR ho tloha mochine o boletsoeng oa voltage.

Meeli ea Tsamaiso ea Alarm ea Mollo

Sesebelisoa sa alamo ea mollo e ikemetseng - ka tloaelo e entsoe ka lisebelisoa tsa mosi, lisebelisoa tsa mocheso, liteishene tsa ho hula ka letsoho, lisebelisoa tsa temoso tse utloahalang le taolo ea alamo ea mollo e nang le bokhoni ba tsebiso e hōle e ka fana ka temoso ea pele ea mollo o tsoelang pele. Leha ho le joalo, tsamaiso e joalo ha e tiise tšireletso khahlanong le tšenyo ea thepa kapa tahlehelo ea bophelo e bakoang ke mollo.

Sistimi efe kapa efe ea alamo ea mollo e ka hloleha ka mabaka a fapaneng:

Lisebelisoa tsa mosi e ka 'na ea se ke ea utloa mollo moo mosi o ke keng oa fihla ho li-detectors tse kang lichimney, maboteng, marulelong, kapa ka lehlakoreng le leng la mamati a koetsoeng. Lisebelisoa tsa ho lemoha mosi le tsona li ka 'na tsa se ke tsa utloa mollo sebakeng se seng kapa mokatong o mong oa mohaho. Mohloli oa mokatong oa bobeli, bakeng sa mohlalaample, e kanna ea se utloe mollo oa mokatong oa pele kapa mokatong o ka tlase. Ho feta moo, mefuta eohle ea lisebelisoa tsa mosi - mefuta e 'meli ea ionization le photoelectric, e na le mefokolo ea ho lemoha. Ha ho mofuta oa mochine o lemohang mosi o ka utloang mofuta o mong le o mong oa mollo o bakoang ke bohlasoa le likotsi tsa tšireletso tse kang ho tsuba betheng, ho phatloha ho matla, khase e phonyohang, polokelo e sa lokelang ea thepa e tukang, lipotoloho tsa motlakase tse tletseng ho tlōla, bana ba bapalang ka licheso, kapa ho chesoa.

BOHLOKOA! Lisebelisoa tsa mosi e tlameha ho kenngoa ka phapusing e le 'ngoe le phanele ea taolo le likamoreng tse sebelisoang ke sistimi bakeng sa ho hokela mehala ea phetiso ea alamo, likhokahano, lipontšo le / kapa matla. Haeba li-detectors li le sieo, mollo o ntseng o hlaha o ka 'na oa senya alamo, oa sitisa bokhoni ba eona ba ho tlaleha mollo.

Joalo ka lisebelisoa tsohle tsa elektroniki tsa boemo bo tiileng, tsamaiso ena e ka sebetsa ka tsela e sa tsitsang kapa ea senyeha ha e le tlas'a maemo a nakoana a bakoang ke lehalima. Le hoja ho se na tsamaiso e sa sireletsehang ka ho feletseng ho tloha lehalima le litšitiso, ho beha fatše ho tla fokotsa ts'oaetso. Lithapo tse holimo kapa tse ka ntle ha li khothalletsoe, ka lebaka la ho ba le monyetla o eketsehileng oa lehalima le haufi. Ikopanye le Lefapha la Litšebeletso tsa Teknoloji haeba ho lebeletsoe hore ho na le mathata afe kapa afe.

Hakolla matla a AC le libeteri pele ho tlosa kapa ho kenya mapolanka a potoloho. Ho hloleha ho etsa joalo ho ka senya li-circuits.

Tlosa likopano tsohle tsa elektronike pele ho ho cheka, ho faela, ho nchafatsa kapa ho phuphunya sebaka se kampetsoeng. Ha ho khoneha, etsa likhakanyo tsohle tsa cable ho tloha ka mahlakoreng kapa ka morao. Pele u etsa liphetoho, etsa bonnete ba hore li ke ke tsa kena-kenana le betri, transformer le sebaka sa boto ea potoloho e hatisitsoeng.

Se ke oa tiisa li-screw terminals ho feta 9 in-lbs. Ho tiisa ho feta tekano ho ka senya likhoele, ho baka ho fokotseha ha khatello ea ho kopana le ho thatafalloa ke ho tlosa li-screw terminal.

Tsamaiso ena e na le likarolo tse utloang static Kamehla u iteole ka leqhama le nepahetseng la letsoho pele u tšoara lipotoloho life kapa life e le hore litefiso tse tsitsitseng li tlosoe 'meleng. Sebelisa sephutheloana sa static suppressive ho sireletsa likopano tsa elektroniki tse tlositsoeng yuniti.

Latela litaelo bukeng ea ho kenya, ho sebetsa le ea ho etsa mananeo. Litaelo tsena li tlameha ho lateloa ho qoba tšenyo ea phanele ea taolo le lisebelisoa tse amanang le tsona. Ts'ebetso ea FACP le ho ts'epahala ho ipapisitse le ho kenya ts'ebetso e nepahetseng.

Le hoja ho kenya alamo ea mollo ho ka ’na ha etsa hore litefiso tse tlaase tsa inshorense li khonehe, ha ho nke sebaka sa inshorense ea mollo!

 Alisebelisoa tsa temoso tse ka tjoang tse kang litloloko li ka 'na tsa se ke tsa lemosa batho haeba lisebelisoa tsena li le ka lehlakoreng le leng la mamati a koetsoeng kapa a bulehileng kapa a le mokatong o mong oa mohaho.

Sistimi ea alamo ea mollo e tla ha e sebetse ntle le matla a motlakase. Haeba motlakase oa AC o hloleha, sistimi e tla sebetsa ho tsoa ho libeteri tsa standby ka nako e behiloeng feela.

Rate-of-Rise mocheso detectors e ka ba tlas'a ho fokotseha ha kutloisiso ha nako e ntse e ea. Ka lebaka lena, tšobotsi ea ho phahama ha sekhahla sa mochine o mong le o mong o lokela ho lekoa bonyane hang ka selemo ke setsebi se tšoanelehang sa tšireletso ea mollo.

Lisebelisoa tse sebelisoang tsamaisong e kanna ea se lumellane ka botekgeniki le phanele ea taolo. Ho bohlokoa ho sebelisa feela lisebelisoa tse thathamisitsoeng bakeng sa ts'ebeletso le phanele ea hau ea taolo.

Tmohala mela e hlokahalang ho fetisa mats'oao a alamo ho tloha sebakeng se itseng ho ea setsing sa tlhahlobo e ka 'na eaba ha e sebetse kapa e holofalitsoe ka nakoana.

Lebaka le tloaelehileng haholo ho se sebetse hantle ha alamo ea mollo, leha ho le joalo, ho hloka tlhokomelo e lekaneng. Lisebelisoa tsohle le li-wiring tsa tsamaiso li lokela ho lekoa le ho hlokomeloa ke litsebi tse kenyang alamo ea mollo ho latela mekhoa e ngotsoeng e fanoang ka sesebelisoa ka seng. Tlhahlobo le liteko tsa sistimi li lokela ho hlophisoa khoeli le khoeli kapa joalo ka ha ho hlokoa ke likhoutu tsa Naha le/kapa tsa lehae. Lirekoto tse ngotsoeng tse lekaneng tsa litlhahlobo tsohle li lokela ho bolokoa.

Tlhokomeliso ea FCC
TLHOKOMELISO: Thepa ena e hlahisa, e sebelisa le ho khantša matla a maqhubu a seea-le-moea 'me haeba e sa kengoa le ho sebelisoa ho latela bukana ea litaelo, e ka baka tšitiso ea likhokahano tsa seea-le-moea, E lekoa 'me ea fumanoa e lumellana le meeli ea sesebelisoa sa komporo sa sehlopha sa A ho latela Karolo ea B ea 15 ea Melao ea FCC, e etselitsoeng ho fana ka ts'ireletso e nepahetseng khahlano le tšitiso e joalo ha e sebetsoa sebakeng sa khoebo. Ho sebetsa ha thepa ena sebakeng sa bolulo ho ka 'na ha baka tšitiso, moo ho tla hlokahala hore mosebedisi a lokise tšitiso eo ka litšenyehelo tsa hae.

Litlhoko tsa Canada

Sesebediswa sena sa dijithale ha se fete meedi ya Sehlopha sa A bakeng sa mello ya lerata la radiation ho tswa ho disebediswa tsa dijithale e behilweng Melaong ya Thibelo ya Radio ya Lefapha la Dikgokahanyo la Canada.

Litekanyetso tsa NFPA

 Phanele ena ea taolo e latela maemo a latelang a NFPA:

NFPA 13 Sistimi ea ho fafatsa
NFPA 15 Metsi a Spray Systems Systems

NFPA 16 Moroallo oa Metsi a Foam le Metsi a Foam-Metsi

NFPA 72 Central Station Signaling Systems (Automatic, Manual, and Waterflow). Protected Premises Unit (E Hloka NOTI•FIRE 911AC DACT kapa MS-5012 Slave Communicator)*

NFPA 72 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Mollo Alarm Systems NFPA 72 Auxiliary (Automatic, Manual, and Waterflow) Fire Alarm Systems. (E hloka 4XTM) NFPA 72 Remote Station (Automatic, Manual, and Waterflow) Mecha ea Alarm Systems. E hloka 4XTM, NOTI•FIRE 911AC DACT*

*Likopo tse hlokang NOTI•FIRE 911AC ha lia amoheloa FM.

Tlhahisoleseling e 'Ngoe

Pele o tsoela pele, sesebelisoa se lokela ho tloaelana le litokomane le litekanyetso tse latelang:

Maemo a NFPA:

NFPA 13 Sistimi ea ho fafatsa

NFPA 15 Metsi a Spray Systems Systems

NFPA 16 Moroallo oa Metsi a Foam le Metsi a Foam-Metsi

NFPA 72 Tlhophiso, Tlhokomelo le Tšebeliso ea Lits'ebetso tsa Matšoao a Seteishene sa Bohareng NFPA 72 ea Lehae, ea Thuso, Seteishene sa Remoutu le Mekhatlo ea Lialamo tsa Mollo NFPA 72 Li-Detectors tse Iketsetsang tsa Mollo.

NFPA 72 Tlhophiso, Tlhokomelo le Tšebeliso ea Lisebelisoa tsa Tsebiso bakeng sa Litsamaiso tsa Alamo ea Mollo NFPA 72 Mekhoa ea Teko bakeng sa Mekhatlo ea Matšoao

Litokomane tsa Underwriters Laboratories:

UL 38 Manual Actuated Signaling Mabokose

Li-Detectors tsa Mosi tsa UL 217, Seteishene se le Mong le se Mengata sa UL 228 Door Closers – Holders for Fire Alarm Systems UL 268 Smoke Detectors for Fire Alarm Systems

UL 268A Li-Detectors tsa Mosi bakeng sa Lits'ebetso tsa Duct UL 346 Lipontšo tsa Phallo ea Metsi bakeng sa Sistimi ea Alarm ea Mollo UL 464 Lisebelisoa Tse Utloahalang tsa Mats'oao

Li-Detector tsa Mocheso tsa UL 521 bakeng sa Lisebelisoa tsa Alarm tsa Mollo
UL 864 Standard for Control Units for Fire Alarm Systems UL 1481 Power Supplies for Fire Alarm Systems
UL 1638 Lisebelisoa tsa Pontšo ea Pono
UL 1971 Lisebelisoa tsa Matšoao bakeng sa Batho ba sa utloeng litsebeng

CAN/ULC-S524-M91 Tekanyetso bakeng sa ho Kenngwa ha Mollo wa Alarm Systems CAN/ULC-S527-M87 Standard for Control Units for Fire Alarm Systems

Tse ling:
NEC Article 300 Wiring Methods NEC Article 760 Fire Alarm Systems

Litlhoko tsa Melao ea Kaho ea Lehae le ea Naha ea Bolaoli ba Lehae ba Nang le Tokomane ea Tokomane ea Sesebelisuoa sa Setsi sa Setsebi sa Taolo, 15378.

1 The PDRP-1001/PDRP-1001A/PDRP-1001E

Likaroloana

• E laoloa ke Microprocessor
• Ho lla le mathata
• Sehlopha sa B (Setaele sa B)/Sehlopha sa A (Setaele D) Ho Qala Lipotoloho tsa Sesebelisoa
• Lihlopha tse peli tsa Sehlopha sa B (Setaele Y)/Sehlopha sa A (Setaele Z) Lipotoloho tsa Tsebiso ea Sesebelisoa
• Lihlopha tse peli tsa B (Setaele sa Y) Lipotoloho tsa Tokollo
• Alamo e akaretsang le li-relay tsa mathata
• Mojule oa boikhethelo bakeng sa libaka tse 4 / li-relay tsa tšebetso (4XZM)
• Mojule oa boikhethelo oa transmitter (4XTM). E lumellana le NFPA 72 e thusang le ea Remote Station Alarm Systems
• Volt ea boikhethelo/amp meter module (4XMM)
• Setsebi sa hole se laoloang ke boikhethelo RZA-4X). E hloka LED Interface Module (4XLM)
• Ho ikhethela puisano ea dijithale (NOTI•FIRE 911AC)*
• E lumellana le NFPA 72 Central Station le NFPA 72 Remote Station Alarm Systems
• E etselitsoe litekanyetso tsa ho fafatsa NFPA 13, 15, le 16
• Tlosa/nomella litaolo ka sebaka sa ho qala
• Khopotso ea Ketsahalo ea ho Qetela
• Tlhokomelo ea mathata a Battery/Earth
• Tšireletso ea fuse ho Lipotoloho tsohle tsa Tsebiso / Tokollo
• RMS e laoloang ke matla a tlhahiso, 2.25 amps
• 7 amp/ hora ho isa ho 15 ampLikhetho tsa betri / hora, ho fihla ho lihora tse 90 tsa standby
• Matla a laoloang a ka busetsoang bocha, 'me a ke keng a hlophisoa bocha
• Tšireletso e pharaletseng ea nakoana
• Sebali sa nako ea ho hlokomela microprocessor (e kenyelletsa MICRO FAIL LED)
• Li-circuits tse hlahisoang li sirelelitsoe khahlanong le liketso tse fosahetseng
• Lileibole tsa boitsebiso ba libaka tsa li-slide-in
• Khabinete ea tšepe e 14.5 ″ bophara ka 16″ bophahamo ka 5″ botebo
• Khetho ea phanele ea moaparo o shoeleng (DP-4X)
• Fokotsa selikalikoe bakeng sa sepakapaka se pakeng tsa 16 ″ center studs (TR-4XR)
• Khetho ea cross-zone (double-interlock).
• Tlhahiso ea Lebokose la Masepala
• Interface Module (4XLM)
• Ts'ebetso ea likotsi tse peli
• Sebali se feto-fetohang sa ho ntša nako
  *Likopo tse hlokang NOTI•FIRE 911AC ha lia amoheloa FM.

Lipotoloho

 Kena Lipotoloho

Phatlalatso ea Bukana / Potoloho ea Mohloli oa 1, Sehlopha sa A (Setaele D)/Sehlopha sa B (Setaele B) Sebono sa Potoloho ea 2, Sehlopha sa A (Setaele D)/Sehlopha sa B (Setaele B)

Phallo ea metsi, Sehlopha sa A (Setaele sa D)/Sehlopha sa B (Setaele B) Tsamaiso, Sehlopha sa A (Setaele D)/Sehlopha B (Setaele B)

Li-circuits tse hlahisoang (li-relay tse thusang tse ka ikhethelang li latela lipotoloho tsena tse 'ne)

Alarm/Waterflow Bell, Class A(Style Z)/Class B (Style Y) Waterflow/Supervisory Bell, Class A(Style Z)/Class B (Style Y) Releasing Circuit 1, Class B (Style Y)
Supervisory Bell/Release Circuit 2, Class B (Style Y)

Liphetoho tsa Taolo ea Phanele e ka Pele

Fetola Molumo oa 1 Ho Khutsa

Fetola 2 Alarm Silence

Switjha 3 Alamo Kenya tshebetsong

Fetola 4 System Reset

Liboto tsa boikhethelo

 PDRP-1001/PDRP-1001A/PDRP-1001E e na le li-slots bakeng sa liboto tse peli tsa khetho. Li-module tse peli ho tse tharo tsa khetho li ka kenngoa.

Mojule oa Transmitter (4XTM - NOTIFIER)

Transmitter Module e fana ka tlhahiso e hlokometsoeng bakeng sa transmitter ea motlakase ea lehae ea masepala (bakeng sa NFPA 72 Auxiliary Fire Alarm System) le alamo le mathata a reverse polarity circuits (bakeng sa NFPA 72 Remote Station Fire Alarm System). Hape ho kenyelelitsoe sesebelisoa sa DISABLE le ho tima LED ea mathata.

E le khetho ea jumper, alamo e khutlisetsang polarity potoloho e tla buleha mathateng haeba ho se na alamo e teng.

 LED Interface Module (4XLM – NOTIFIER)

LED Interface Module e tšehetsa mojule oa RZA-4X Remote Annunciator. Wiring ea Annunciator e laoloa bakeng sa maemo a bulehileng ke mojule ona. Annunciator Driver Module e nyolohela botong e kholo, e nka e 'ngoe ea lihokelo tse peli tsa khetho.

Zone Relay Module (4XZM – NOTIFIER)

Mojule oa Zone Relay o fana ka mabitso a Foromo-C bakeng sa tse latelang:

• Alarm/Kello ea Phallo ea Metsi
• Metsi a phallang / Supervisory Bell
• Releasing Circuit 1
• Supervisory Bell/Release Circuit 2
• Alamo ea Sisteme
• Mathata a Tsamaiso

E le khetho ea jumper, li-relay tse 'nè tsa pele tse hlalositsoeng ka tlase li ka etsoa hore ho khutse ho khonehe.

 Mojule oa Transmitter (4XTM - NOTIFIER)

Bakeng sa tšebeletso ea Local Energy Municipal Box (NFPA 72 Auxiliary Fire Alarm System)
Tsamaiso ea hona joale: 5.0 mA

Leeto la hona joale: 0.35 amps. (E ntšitsoe ho matla a Notification Appliance) Coil Voltage: 3.65 VDC
Khahlano ea li-coil: 14.6 ohms
Boemo bo phahameng bo lumelletsoeng ba terata pakeng tsa phanele le khoele ea leeto: 3 ohms Wiring Box Box e ka tloha mohahong

Bakeng sa Tšebeletso ea Seteishene sa Remote

(Seteishene sa Alamo sa Mollo sa NFPA 72 Remote Station):

Boholo ba mojaro bakeng sa potoloho ka 'ngoe: 10mA Reverse polarity output voltage: 24 VDC

Alamo ea Remoutu le Wiring ea Remote Mathata li ka tsoa mohahong

LED Interface Module (4XLM – NOTIFIER)

Boholo voltage/hona joale, tlhahiso ka 'ngoe: 27.6V/8mA

Ela hloko: Lintho tse hlahisoang li na le matla a fokolang

Zone Relay Module (4XZM – NOTIFIER)

Mabitso a Dry Form-C a fuoe lintlha tse latelang: 2.0 amps @ 30VDC (ho hanyetsa), 0.5 amps @ 30 VAC (ho hanyetsa)

Annunciator e hole

Remote Annunciator (RZA-4X – NOTIFIER)

Remote Annunciator e hloella lebokoseng le tloaelehileng la sehlopha se le seng, 'me e fana ka pontšo ea LED ea tse latelang:

• Alamo/Kello ea Phallo ea Metsi (e khubelu)
• Kelo ea Phallo ea Metsi/Tsamaiso (e khubelu)
• Releasing Circuit 1 (red)
• Supervisory Bell/Release Circuit 2 (e khubelu)
• LED ya Mathata a Sisteme (yellow)

Ho boetse ho fanoe ka Local Trouble Sounder le Silence Switch. Lithapo tsohle tsa LED li laoloa bakeng sa maemo a bulehileng. Boemo bofe kapa bofe bo bulehileng bo tla etsa hore LED ea Bothata ba Tsamaiso e bonese.

Tlhokomeliso: The Remote Annunciator e hloka tšebeliso ea LED Interface module (4XLM).

Limithara tsa boikhethelo

Moqtage, Current Memeter (4XMM – NOTIFIER)

Meter Module e fana ka voltmeter ho metha voltage ka mose ho libeteri le ammeter ho lekanya motlakase oa ho tjhaja libeteri. Limithara li fanoe e le kopano e nyolohelang hukung e ka tlase ea letsoho le letšehali la khabinete.

Litlhaloso

 Matla a AC

Bakeng sa PDRP-1001/PDRP-1001A/PDRP-1001E: 120
VAC, 50/60 Hz, 1.2 amps
Bakeng sa PDRP-1001E: 220/240 VAC, 50 Hz, 0.6 amps
Boholo ba terata: bonyane #14 AWG e nang le insulation ea 600V

Betri (lead acid feela)

Potoloho e phahameng ea ho tjhaja: 27.6V, 1.5 amps
Bophahamo ba Bokhoni ba Betri: 15 AH. (Libetri tse kholo ho feta 12 AH li hloka NOTIFIER #BB-17 kapa khabinete e 'ngoe ea UL e thathamisitsoeng ka ntle ea betri.)

Ho qala lipotoloho tsa lisebelisoa

Potoloho e nang le matla a lekanyelitsoeng
Tshebetso: Sehlopha sa A (Setaele D)/Sehlopha sa B (Setaele B)
Tloaelehileng Operating Voltage: 24 VDC (ripple = 1.0V peak-to-tlhōrō) Alamo ea hona joale: 15 mA bonyane
Nako e khutšoanyane ea potoloho: 40 mA boholo
Boholo ba detector hona joale boemong ba standby: 2 mA (max) sebakeng ka seng Bongata ba ho hanyetsa loop: 200 ohms
Mohanyetsi oa ho qetela: 4.7K, 1/2-Watt (TSEBISO karolo ea # 71252, UL e thathamisitsoe)
Detector loop current e lekane ho netefatsa ts'ebetso ea detector e le 'ngoe e tšosang sebakeng ka seng. Tlhokomelo ea hajoale: 5 mA (ho kenyeletsoa le sehanyetsi sa ho qetela)

Notification Appliance and Releasing Circuits

Potoloho e nang le matla a lekanyelitsoeng
Boholo bo lumelletsoeng ka matlatage theohile ka lebaka la wiring: 2 VDC Normal Operating Voltage: 24 VDC
Kakaretso ea hajoale e fumanehang ho lisebelisoa tsohle tsa kantle: 2.25 amps
Boholo ba hona joale ba pontšo ka potoloho: 1.5 amps
Mohanyetsi oa ho qetela: 4.7K, 1/2-Watt (TSEBISO karolo ea # 71252, UL e thathamisitsoe)

Alamo le Mathata a Relays

Mabitso a Dry Form-C a fuoe lintlha tse latelang: 2.0 amps @ 30 VDC (ho hanyetsa), 0.5 amps @ 30 VAC (ho hanyetsa). Li-relay tsohle li tlameha ho hokeloa phepelong ea motlakase e lekanyelitsoeng.

Matla a Mosi oa Mosi oa terata e mene

Ho fihla ho 200 mA e fumaneha bakeng sa ho matlafatsa lisebelisoa tse 4 tsa mosi. Boholo ba ripple voltage: 1.0 V p/p

Matla a sa tsitsang

Kakaretso ea hajoale ea DC e fumanehang ho tsoa tlhahisong ena e fihla ho 200 mA (e ntšitsoeng ho matla a mosi oa terata tse 4).

Boholo ba ripple voltage: 1.0 V p/p

Matla a laoloang ke RMS

Kakaretso ea hajoale ea DC e fumanehang bakeng sa ho matlafatsa lisebelisoa tsa kantle ke 0.5 amp (e ntšitsoeng ho

2.25 amps fumaneha ho lipotoloho tsa lisebelisoa tsa tsebiso). Boholo ba ripple voltage: 100 mV p/p

Tlhokomeliso: Bakeng sa ho lumellana ha sesebelisoa, sheba Chate ea Tšebelisano ea Sesebelisuoa.

Ts'ebetso ea Sisteme

Li-LED tsa Boemo ba Tsamaiso

Li-LED tsa Alamo, Mathata le Tlhokomelo li tla khantša le ho tima ho fihlela ketsahalo e amoheloa (TONE kapa ALARM SILENCE), ka nako eo LED e tla bonesa butle-butle.

AC MATLA
LED e tala e khantšang butle-butle ho bontša boteng ba matla a AC.

TŠEBELETSO TSATSI
LED e khubelu e phatsimang ha alamo e hlaha.

RELEBOHILE
LED e khubelu e khantšang ka mokhoa o tsitsitseng ha ho lokolloa ho etsahala.

SUPERVISORY
LED e mosehla e bonesang ha e kenya tšebetsong sesebelisoa se okametseng (joalo ka tamper switch) ho Output 4 ha e khethiloe (sheba "Setting Mode of Operation" Karolong ea 3 ea bukana ena).

TSAMAISO MATHATA
LED e mosehla e benyang bakeng sa boemo bofe kapa bofe ba mathata, ho kenyelletsa le tse amanang le liboto tsa khetho.

TS'ELISO MATHATA
Yellow LED that flashes for trouble conditions on output circuits (notification and releasing circuits).

TLHOKOMELISO THUSO
LED e mosehla e bonesang butle-butle ha sesebelisoa sa ALARM SILENCE se sutumelitsoe ka mor'a alamo.

MATLA MATHATA
LED e mosehla e bonesang bakeng sa libeteri tse tlase kapa tse khaotsoeng le maemo a phoso a lefats'e.

BETTI
LED e tšehla e bonesang butle-butle holim'a boardboard ha betri e le tlase kapa e sa lemohuoe (ha e bonahale monyako).

LEFATŠE
LED e mosehla e bonesang butle-butle holim'a lebokose la li-motherboard nakong ea bothata ba fatše (e sa bonahaleng monyako)

MICRO HLOKA
LED e tšehla e bonesang holim'a motherboard ha sebali sa nako se lemoha ho hloleha ha microprocessor (ha e bonahale monyako)

Laola Liphetoho

Li-LED tsa Boemo ba Zone 

Alamo le/kapa li-LED(li) mathata li tla khanya ho fihlela (li)diketsahalo li amohetsoe (TONE kapa ALARM SILENCE), ka nako eo li-LED li tla bonesa butle.

Tlhokomelo

Zone 4 e lula e sebelisoa bakeng sa lisebelisoa tsa ho beha leihlo (tse kang valve tampli-switches). Potoloho e khuts'oane sebakeng sena (ts'ebetso ea NO contact) e tla etsa hore supervisory LED le zone 4 yellow LED li bonese. Molumo oa molumo oa piezo o tla hlahisa molumo o ikhethang oa Pressing TONE SILENCE e tla khutsisa piezo mme e etse hore LED e okametseng e bonese butle-butle, empa Zone 4 Trouble LED e tla tsoela pele ho khanya.
Matshwao a ho okamela a honyetsa mme a hloka RESET hore e hlweke. Sesebelisoa sa ALARM SILENCE se tla khutsisa piezo, se etse hore LED e okametseng e bonese butle-butle ebe e tima
Temoso ea Tsamaiso ea Sesebelisuoa sa Potoloho. Potoloho e bulehileng ho Zone 4 e tla tlalehoa e le bothata ba libaka.

Tlosa Zone

Haeba sebaka se koetsoe, alamo e hlahang sebakeng seo e tla khantša LED ea sebaka se sefubelu, empa eseng piezo kapa seketsoana sefe kapa sefe. Haeba mehloli ea motlakase ka bobeli e tlositsoe ho sistimi, libaka tsohle li tla fuoa monyetla ha ho tsosolosoa matla. Boemo ba ho tima bo tla lahleha.

The Zone Disable routine e sebelisa li-switches tse 'ne ka tsela e latelang:

1. Tobetsa o hatelle konopo ea TONE SILENCE.
2. Ka TONE SILENCE switch e kentsoeng, tobetsa (ka tatellano) switch ea ALARM SILENCE, ALARM ACTIVATE switch, 'me ka mor'a moo ea RESET.
3. The Zone 1 Alarm LED e tla
4. Ho tima Zone 1, tobetsa RESET The Zone 1 yellow LED e tla khantša ho bontša hore sebaka se holofetse.

Tlhokomeliso: The RESET switjha e tima boemo ba sebaka se khethiloeng.

5. Ho khetha sebaka se latelang, tobetsa ALARM SILENCE
6. Ho khetha sebaka se fetileng, tobetsa ALARM ACTIVATE
7. Ha khetho ea ho tima e phethiloe, lokolla TONE SILENCE

Haeba sebaka se seng le se seng se holofalitsoe, phetisetso ea mathata e tla qala mme System Trouble LED e tla khanya.

Khopotso ea Ketsahalo ea ho Qetela

Khopotso ea Ketsahalo ea ho qetela e lumella mosebelisi ho hlahisa boemo ba phanele e fetileng. Sehopotso sa ketsahalo ea ho qetela se sebelisa li-switches tse 'ne ka tsela e latelang:

1. Tobetsa 'me u hatelle HO KHUTSA HO TŠOETSOA
2. Ha konopo ea TONE SILENCE e kentsoe, tobetsa (ka tatellano) konopo ea RESET, ALARM ACTIVATE switch, ebe ALARM SILENCE.
3. Ketsahalo ea ho qetela ke
4. Lokolla switch ea TONE SILENCE ho khutlela setloaeleng

Tlhokomeliso: Ho hlakola "buffer" ea ho qetela, tobetsa RESET habeli.

3 Mokhoa oa ho kenya

 Kakaretso

 Hlakola tsamaiso ka hloko 'me u hlahlobe hore na ho na le tšenyo ea likepe. Kenya khabinete sebakeng se hloekileng se omeletseng, se se nang ho thothomela moo mocheso o feteletseng o sa kopaneheng. Sebaka se lokela ho fumaneha habonolo ka sebaka se lekaneng bakeng sa ho kenya le ho hlokomeloa habonolo. Beha bokaholimo ba khabinete hoo e ka bang limithara tse hlano ka holim'a fatše 'me hinge e ka letsohong le letšehali. Etsa qeto ea palo ea li-conductor tse hlokahalang bakeng sa lisebelisoa tse lokelang ho sebelisoa. Hula li-conductors tse hlokahalang ka lebokoseng ka ho kokota ho fanoeng. Lithapo tsohle li lokela ho tsamaellana le likhoutu tsa Naha le/kapa tsa Local bakeng sa lisebelisoa tsa alamo ea mollo.

Litlhoko tsa Wiring tsa UL Power Limited

Motlakase o lekanyelitsoeng le o se nang matla o fokolang oa motlakase o tlameha ho lula o arohane ka khabinete. Lithapo tsohle tsa motlakase tse lekanyelitsoeng li tlameha ho lula bonyane 0.25 in (6.35 mm) hole le lithapo life kapa life tse lekanyelitsoeng tsa motlakase. Ho feta moo, lithapo tsohle tse nang le matla a lekanyelitsoeng le lithapo tsa potoloho tse se nang matla li tlameha ho kena le ho tsoa ka har'a khabinete ka li-knockout le/kapa li-conduits tse fapaneng. Setšoantšo se tloaelehileng sa wiring bakeng sa PDRP-1001/ PDRP-1001A/PDRP-1001E se bontšitsoe ka tlase.

Ho qala lipotoloho tsa lisebelisoa

Libaka

Hokela lisebelisoa tsohle tse qalang alamo ka tatellano bakeng sa tlhokomelo e nepahetseng. Lisebelisoa tse qalang li kenyelletsa: lisebelisoa tsa mocheso, photoelectric, le mofuta oa ionization; le lisebelisoa tsa alamo ea phallo ea metsi. Sheba Chate ea Tšebelisano e Sehlomathisong sa B.

Hlokomela:

• Ela hloko polarity ha o hokela polarized
• Lipotoloho tsohle li laoloa ebile li na le matla
• Tlohela Dummy Load (e fanoeng) ho tsohle tse sa sebelisoeng

4- Mahokelo a Mosi oa Mosi

Sheba Tokomane ea Tšebelisano ea Sesebelisuoa bakeng sa lisebelisoa tse 4 tse loketseng tsa ho tseba mosi.

Lintlha tsa Sehlopha sa A (Setaele sa D) le sa Sehlopha sa B (Setaele B) sa marang-rang:

1. Likhoele tsa Power Supervision Relay li tlameha ho hokeloa ho litheminale tsa 24V tsa ho qetela tsa detector.
2. Palo ea khanyetso e phahameng e lumelletsoeng ho terata ea motlakase ea 24VDC:

RMAX  =    (20.6 - VOM)
(N x ke_S+ (N_A x ke_A) + (I_R)

Moo:

R_MAX ke khanyetso e phahameng ea lithapo tsa 24V.

V_OM ke bonyane ba matla a ho sebetsatage ea detector kapa end-of-line relay, ho sa tsotellehe hore na e kholoanyane, ka li-volts.

N ke palo eohle ea li-detectors ho lupu ea phepelo ea 24V.

I_S ke sesupo sa boemo ba hajoale ba standby.

N_A ke palo ea li-detectors tse ho loop ea matla ea 24V e lokelang ho sebetsa ka nako e le 'ngoe ka alamo.

I_A ke sesupa sa motlakase se hlahang alamo.

I_R ke pheletso ea mohala oa relay hajoale.

Lipotoloho tse hlahisoang

 Lipotoloho tsa Sesebelisoa sa Tsebiso

This control panel can provide two Class A (Style Z)/Class B (Style Y) Notification Appliance Circuits and two Class B (Style Y) Releasing Circuits (see section “Setting Mode of Operation” for DIP switch configuration). Each circuit is capable of 1.5 amps ea hona joale. Kakaretso ea hajoale e nkiloeng ho lipotoloho tse 'ne e ke ke ea feta 2.25 amps. Sheba Chate ea Tšebelisano. Lipotoloho li laoloa ebile li na le matla a fokolang.

Ela hloko: Wiring e tlameha ho hlophisoa ho boloka bonyane ba voltage ea 20.4V lipotolohong tsa tokollo. Palo ea boholo bo lumelletsoeng ba khanyetso:

Note: Output #4 can be configured for releasing or supervisory circuit (see Section “Setting Mode of Operation”). If configured as a releasing circuit, the circuit will be non-power limited. If configured as a supervisory circuit, the circuit will be power limited. All wiring must follow the power limited “General” Section.

Setšoantšo sa 6 Lipotoloho tsa Sesebelisoa sa Tsebiso

Alamo Relay

Khokahano e le 'ngoe ea alamo ea Foromo ea C e fanoa phanele ea mantlha bakeng sa ho laola lisebelisoa tsa tlatsetso. E fuoe lintlha tse 2 amps ho 30 VDC le 0.5 amps at 30 VAC (resistive), 'me ha e khone ho khutsa ha alamo e hlaha. Sheba ka tlase bakeng sa sebaka sa terminal.

Relay ea mathata

Khokahano e le 'ngoe ea Foromo ea C ea mathata e fanoa phanele ea mantlha bakeng sa ho laola lisebelisoa tsa tlatsetso. E fuoe lintlha tse 2 amps ho 30 VDC le 0.5 amps ho 30 VAC (resistive), 'me e tla khutsa ha boemo ba mathata bo hlakotsoe. Sheba ka tlase bakeng sa sebaka sa terminal.

Tlhokomeliso: Alamo le mathata a Foromo ea C ea likhokahano tse omeletseng e tlameha ho ba li-relay tse lekanyelitsoeng tsa matla. Li tlameha ho hokelloa ho tsoa ho e 'ngoe ea litheminale tse lekanyelitsoeng tsa matla a 24V joalo ka ha ho bonts'itsoe setšoantšong se ka tlase kapa phepelo ea motlakase e lekantsoeng ea UL e thathamisitsoeng ho UL.

Matla

⚠ TLHOKOMELISO: Mehloli e mengata e fapaneng ea matla e ka hokeloa phanele ena. Hlakola mehloli eohle ea matla pele u sebeletsa. Phanele le lisebelisoa tse amanang le tsona li ka senyeha ka ho ntša le/kapa ho kenya likarete, li-module, kapa likhoele tse hokelang ha yuniti ena e ntse e matlafatsoa.

Matla a AC

Matla a mantlha a hlokahalang bakeng sa phanele ea PDRP-1001/PDRP-1001A/PDRP-1001E ke 120 VAC, 50/60 Hz, 1.2 amps le matla a mantlha a PDRP-1002E ke 220/240 VAC, 50 Hz, 0.6 amps. Tšireletso e fetelletseng ea potoloho ena e tlameha ho latela Article 760 ea Khoutu ea Naha ea Motlakase (NEC) le/kapa likhoutu tsa lehae. Sebelisa #14 AWG (2.00 mm2) kapa terata e kholoanyane e nang le lintlha tse 600 tsa volt.

Matla a Battery

Ela hloko polarity ha o hokela betri. Hokela thapo ea betri ho J9 botong e kholo u sebelisa sehokelo sa plug-in se fanoeng. Sheba Sehlomathiso sa A bakeng sa lipalo tsa litekanyetso tse nepahetseng tsa betri.

⚠ TLHOKOMELISO: Libetri li na le sulphuric acid e ka bakang cheso e mpe letlalong le mahlong, 'me e ka senya masela. Haeba ho kopana ho etsoa ka sulfuric acid, hang-hang hlatsoa letlalo kapa mahlo ka metsi ka metsotso e 15 'me u batle thuso ea bongaka hang-hang.

Voltmeter / Ammeter

Ho beha leihlo matla a betri voltage le betri ea hona joale, 4XMM (NOTIFIER) ea hlokahala. Ho kenya mochini oa meter ea matla, tlosa jumper e ngotsoeng "AMP” ebe o hokela kopano ea cable P2 ho penya sehokelo J2 le kopano ea cable P3 ho penya sehokelo J3 botong e kholo. Sireletsa 4XMM ka lebokoseng le ka morao ka li-screw tse peli tse fanoeng. Mehlala e meng, ho tla hlokahala ho kenya bracket ea meter ka linate le liboutu tse fanoeng.

Mekhoa ea ho ikhethela

 Phanele ea taolo ea mollo e na le likhokahano tse peli tsa module - J5 le J8. Li-module tse tharo li teng bakeng sa phanele 'me li ka sebelisoa ka motsoako ofe kapa ofe, ho kenyelletsa le li-module tse kopitsoang. Jumper e tsamaisanang le khetho e tlameha ho khaoloa pele ho kengoa mojule oa boikhethelo, ho etsa hore mojule a okamele.

Ho kenya li-Module tsa Khetho

Kenya li-stand-offs tse peli (tse fanoeng) ka har'a masoba a ka lehlakoreng le letona la boto e kholo. Lokisetsa ka hloko lithakhisa letlapeng le leholo le J1 le/kapa J2 letlapeng la khetho. Kenya screw ka har'a boto ea khetho ho fihlela e tiisitsoe ho li-stand-offs. Kenya li-label tsa boitsebahatso tse fanoeng le li-module tsa khetho joalo ka ha ho bonts'itsoe ka tlase.

Mojule oa Transmitter - 4XTM (NOTIFIER)

Polarities e bonts'itsoeng maemong a kentsoeng. Ho kenngoa ha mojule ona ho tlameha ho latela litlhoko tse boletsoeng karolong ea "Kakaretso", ".Litlhoko tsa Wiring tsa UL Power Limited.”

Tobetsa konopo ea ho khaola ho thibela ho kenya tšebetsong ho sa batleheng ha Lebokose la Masepala le Liphetho tsa Seteishene sa Remote nakong ea tlhahlobo ea phanele ea taolo. The Disconnect LED e tla lula e bonesitsoe ha Lebokose la Masepala le ntse le khaotsoe. The System Trouble LED e tla bontša maemo a khaotsoeng le/kapa Open Circuit lebokoseng la Masepala. Ho khaola jumper ea TBL ho tla lumella alamo ea reverse polarity hore e bulehe mathateng, haeba ho se na alamo.

Tlhokomeliso: Alamo ea Remoutu, Mathata a Remote, le lithapo tsa Mabokose a Masepala li ka tsoa mohahong.

Zone Relay Module – 4XZM (NOTIFIER)

Lithapo tse se nang matla le tse nang le matla a fokolang li tlameha ho ba le sebaka sa bonyane ba terata ea 0.25 in. (6.35 mm). Haeba mojule ona o sebelisoa ho khanna li-circuits tse se nang matla a fokolang le matla a fokolang, ka kopo latela litaelo tse ka tlase.

Relay #1 ho isa ho #4 e tla sebetsa ka Output #1 ho isa ho #4 'me e lule e tsitsitse ntle le hore jumper "LATCH" e khaotsoe.

Tlhokomeliso: Sheba lebokose la Protected Premises Unit, le monyako oa phanele ea taolo, ho bontša hore na ho na le likhokahano tse omeletseng tse tla sebelisoa e le likhokahano tse ommeng tse se nang matla.

LED Interface Module - 4XLM (NOTIFIER)

Mehala ea mojule ona e tlameha ho latela litlhoko tse boletsoeng karolong "Litlhoko tsa Wiring tsa UL Power Limited.”

Dip Switch Location le Litlhaloso

Bakeng sa litlhophiso tsa switjha tsa DIP, sheba Karolo "Ho beha mokhoa oa ho sebetsa.”

Ho beha mokhoa oa ho sebetsa

Lenaneo la Motheo

Khetha mokhoa o lakatsehang oa ts'ebetso 'me u sete li-switches tsa SW1 DIP 1 le 2 ho latela kholomo e nepahetseng.

Nako ea ho hlakola

Khetha setlama se lakatsehang sa Discharge Timer ka ho seta li-switches tsa SW1 DIP 3, 4 le 5.

Bakeng sa lits'ebetso tsa NFPA 13 le 15, Sebali se tlameha ho hlophisoa ho DISABLED.

Bakeng sa lits'ebetso tsa NFPA 16, Sebali se ka beoa ho 10 MINUTES kapa 15 MINUTES.

Hlokomela: Nako ea ho Lahlela:

• Nako e tla lula e qala ho Zone 2 e tloaelehileng ho lla Ha nako e felile, li-circuits tsa tokollo tse tsamaellanang li tla tima.
• Zone 1 e tla lula e tlola nako ea ho koala nako (ntle le Mode #4 - Phallo ea Phallo).

Sehlomathiso A: Lipalo tsa Matla

Litlhokahalo tsa Battery ea Standby

Palo ea Battery e Emeng Hajoale e fumanoeng lethathamong le latelang (Letlapa la 1) le emela chelete ea hajoale e tlamehang ho fanoa ke mohloli oa bobeli oa matla (libetri) ho boloka tšebetso ea phanele ea taolo bakeng sa hora e le 'ngoe.

Tlhokomeliso: Phanele ea taolo e tla ts'ehetsa ho kengoa ha mojule o le mong kapa tse peli tsa boikhethelo, ho kenyeletsoa tse peli tsa mofuta o tšoanang oa mojule.

AmpLipalo tsa ere-Hour

Khetha betri e lekanang kapa e kholoanyane amp/reite ea hora ho feta palo e fumanoeng ka Letlapa la 2. Libetri li tlameha ho ba mofuta oa lead-acid.

PS-1270 12 volt, 7 amp/hora (tse peli tse hlokahalang) PS-12120 12-volt, 12 amp/hora (tse peli lia hlokahala)

Lintlha:

1. Alamo amp-Lihora li nka palo e kholo ea tsamaiso ea 3 amps ka alamo bakeng sa metsotso e 5 (0.25 amp/hora) kapa metsotso e 10 (0.5 amp/hora)
2. NFPA 72 Central Station le Local and Proprietary Alarm Systems e hloka lihora tse 24 tsa
3. NFPA 72 Thuso le Seteishene sa Remote Alamo ea Alamo e hloka lihora tse 60 tsa
4. Factory Mutual Systems e hloka lihora tse 90 tsa
5. Chaja ea betri phanele ena e tla tjhaja boholo ba 15 amp/ lihora tsa libeteri nakong ea lihora tse 48 (7 amp/hora bonyane). Libetri tse kholo ho feta 12 amp/ hora e tla hloka khabinete e thathamisitsoeng ea UL (mohlala NOTIFIER BB-17).

Sehlomathiso B: Tšebelisano ea Sesebelisoa

Mosireletsi oa Mosi/Motheo	Mofuta oa detector	Max Standby Current (mA)	Alarm Current (mA)
Sensor ea Sisteme 2424	Motlakase oa lifoto	0.10	41
Sensor ea Sisteme 2424TH	Motlakase oa lifoto	0.10	41
Sensor ea Sisteme 2451	Motlakase oa lifoto	0.10	39
Sensor ea Tsamaiso 2451TH (e nang le/B402B Base)	Motlakase oa lifoto	0.10	39
Sensor ea Sisteme 1424	Ionization	0.10	41
Sensor ea Tsamaiso 1451 (w/B402B Base)	Ionization	0.10	39
Sensor ea Sisteme 2412	Motlakase oa lifoto	0.12	77
Sensor ea Sisteme 2412AT	Motlakase oa lifoto	0.12	58
Sensor ea Sisteme 2412TH	Motlakase oa lifoto	0.12	77
Sensor ea Sisteme 2312/24TB	Motlakase oa lifoto	0.12	50
Sensor ea Sisteme B112LP	Motheo	0.12	36
Sensor ea Sisteme B114LP	Motheo	—–	—–
Sensor ea Sisteme B404B	Motheo	—–	—–
Sensor ea Sisteme 6424	Beam e lebelletsoeng	10	28.4
Sensor ea Sisteme DH400ACDCI	Mokelikeli oa ionization	25	95
Sensor ea Sisteme DH400ACDCP	Mokelikeli oa Photoelectric	25	95
Sensor ea Sisteme 1112/24	Ionization	0.05	50
Sensor ea Sisteme 2112/24	Motlakase oa lifoto	0.05	50
Sensor ea Sisteme 2112/24B	Motlakase oa lifoto	0.05	65
Sensor ea Sisteme 2112/24T	Motlakase oa lifoto w/135° Thermal	0.05	50
Sensor ea Sisteme 2112/24TSRB	Motlakase oa lifoto w/135° Thermal Supervisory Relay	15	45

Lethathamo la 3 UL le thathamisitsoeng ka Mehala e Mene ea Mosi

 FM-Approved Releasing Devices

(System Sensor's PDRP-1001/PDRP-1001A/PDRP-1001E)

Sehlopha sa Solenoid [A] Skinner solenoid valve Model LV2LBX25, 24 VDC, 11 Watts, 458 mA, 1/2 in. NPS, 5/ 8 in. orifice.

Sehlopha sa Solenoid [B] Li-valve tsena lia fetoha.
ASCO solenoid valve Model T8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS, 5/8 in. orifice.

ASCO solenoid valve Model R8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS, 5/8 in. orifice.

ASCO solenoid valve Model 8210A107, 24 VDC, 16.8 Watts, 700 mA, 1/2 in. NPS, 5/ 8 in. orifice.

Sehlopha sa Solenoid [C] Star Sprinkler Corp. Solenoid P/N 5550, 24 VDC, karolo ea Model D valve ea moroallo. Hlooho ea Taolo ea Motlakase ea Kidde-Fenwal P/N 890181; 24V, 2.0 Amps

Hlooho ea Taolo ea Motlakase ea Kidde-Fenwal P/N 899175; 24V, 2.0 Amps

Kidde-Fenwal Motlakase Control Head Stackable (XP) P/N 48650001; 24V, 0.2 Amps

Kidde-Fenwal Motlakase le Cable Op Control Head (XP) P/N 897494; 24V, 1.5 Amps, 33 Watts

Sheba tataiso ea tumello ea FM bakeng sa li-valve tsa ho laola metsi ka boiketsetso tse tsamaisanang le li-solenoid tse thathamisitsoeng ka holimo. 

Mohlala	Mofuta	Hona joale (mA)
FM980-24	Floor Mount, motho a le mong	68
FM996-24	Mount Mount Surface Wiring	68
FM998-24	Lebota Thaba e patehileng Wiring	68
DH150A	Mokatong Mount	96
DH154A	Thaba ea Thaba	96
DH158A	Thaba e kaholimo	96

 Tafole 4 24 VDC Door Holders 

Morekisi	Mohlala	Hona joale (MA)
Sensor ea Sisteme	A77-716B	20
Air Products & Controls, LTD	MR-101/C	15
	MR-201/C	35

 Lethathamo la 5 UL Le thathamisitsoe 24 VDC Relays

TS'ELISO TS'OANELO	E lekantsoe Voltage²	FWR DC	E tlhotliloeng DC
Sensor ea tsamaiso MA-12 / 24D Electronic Sounder	24VDC	73	46
Sensor ea Sisteme SS24 Strobe	24VDC	hlokomela 5	30
Sensor ea Sisteme SS24LO Strobe	24VDC	45	25
Sensor ea Sisteme SS24LOC Ceiling Strobe (SS24LOBC - beige)	24VDC	45	25
Sensor ea Sisteme SS24M Strobe	24VDC	125	75
Sensor ea Sisteme SS24MC Ceiling Strobe	24VDC	125	75
Sensor ea tsamaiso MASS24D Electronic Sounder/Strobe	24VDC	118	71
Sensor ea tsamaiso MASS24LO Electronic Sounder/Strobe	24VDC	118	71
Sensor ea Sisteme MASS24LOC Electronic Ceiling Sounder/Strobe	24VDC	118	71
Sensor ea Tsamaiso MASS24LOLA Electronic Sounder/Strobe e nang le lense ea Fuego	24VDC	118	71
Sensor ea Sisteme MASS24M Electronic Sounder/Strobe	24VDC	198	121
Sensor ea Sisteme MASS24MC Electronic Ceiling Sounder/Strobe	24VDC	198	121
Sensor ea Sisteme PA400R Sounder	24VDC	hlokomela 5	15
Sensor ea Sisteme PS24LO Add-on Strobe	24VDC	45	25
Sensor ea Sisteme SS2415ADA Signaling Strobe	24VDC	90	75
Sensor ea Sisteme SS2475ADA Signaling Strobe	24VDC	200	170
Sensor ea Sisteme SS24110ADA Signaling Strobe	24VDC	245	210
Sensor ea Sisteme SS241575ADA Signaling Strobe	24 VDC	120	93
Sensor ea Sisteme SS2415ADAS Signaling Strobe e nang le Synch. Potoloho	24 VDC	125	106
Sensor ea Sisteme SS241575ADAS Signaling Strobe e nang le Synch. Potoloho	24 VDC	180	115
Sensor ea Sisteme MASS2415ADA Sounder/Signing Strobe	24VDC	163	121
Sensor ea Sisteme MASS2475ADA Sounder/Signing Strobe	24VDC	273	216
Sensor ea Sisteme MASS24110ADA Sounder/Signing Strobe	24VDC	318	256
Sensor ea Sisteme MASS241575ADA Sounder/Signing Strobe	24 VDC	193	139
Sensor ea Sisteme MASS2415ADAS Sounder / Signing Strobe w/ Synch. Ckt.	24 VDC	163	121
Sensor ea Sisteme MASS241575ADAS Sounder / Signing Strobe w/ Synch. Ckt.	24 VDC	193	139
Sensor ea Sisteme PS2415ADA Mini-Sounder/Strobe	24VDC	110	90
Sensor ea Sisteme PS2475ADA Mini-Sounder/Strobe	24VDC	135	108
Sensor ea Sisteme PS241575ADA Mini-Sounder/Strobe	24VDC	135	108
Sensor ea Sisteme PS24110ADA Mini-Sounder/Strobe	24VDC	240	225
Sebui sa Sistimi SP1R2415ADA Sebui/Spain Strobe	24VDC	90	75
Sebui sa Sistimi SP1R2475ADA Sebui/Spain Strobe	24VDC	200	170
Sebui sa Sistimi SP1R24110ADA Sebui/Spain Strobe	24VDC	245	210

Sebui sa Sistimi SP1R241575ADA Sebui/Spain Strobe	24 VDC	120	93
Sensor ea Sisteme V4R2415ADA Sebui/Signing Strobe	24VDC	90	75
Sensor ea Sisteme V4R2475ADA Sebui/Signing Strobe	24VDC	200	170
Sensor ea Sisteme V4R24110ADA Sebui/Signing Strobe	24VDC	245	210
Sensor ea Sisteme V4R241575ADA Sebui/Signing Strobe	24 VDC	120	93
Sistimi ea Sensor SP100W24LOC Ceiling Speaker/Strobe, 8″ grille e chitja	24VDC	45	25
Sebui sa Sistimi SP101R24LO Speaker/Strobe, 5″ square grille	24VDC	45	25
Sebui sa Sistimi SP101R24M Speaker/Strobe, 5″ grille ea lisekoere	24VDC	125	75
Sebui sa Sistimi SP100W24MC Ceiling Speaker/Strobe, 8″ grille e chitja	24VDC	125	75
System Sensor MA12/24EH Multi Alert Horn e nang le Mechanical Tone	12VDC/ 24VDC	20/64	38/43
System Sensor MAEH24LO Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	109	68
System Sensor MAEH24LOC Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	109	68
System Sensor MAEH24LOLA Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	153	96
System Sensor MAEH24M Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	189	118
System Sensor MAEH24MC Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	189	118
System Sensor MAEH1215ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	12VDC	240	191
System Sensor MAEH121575ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	12VDC	310	246
System Sensor MAEH2415ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	278	216
System Sensor MAEH2475ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	273	216
System Sensor MAEH241575ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	343	271
System Sensor MAEH24110ADA Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	318	256
System Sensor MAEH2415ADAS Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	198	152
System Sensor MAEH241575ADAS Multi Alert Horn e nang le Mechanical Tone/Strobe	24VDC	253	241
Sensor ea Sisteme H12 SpectrAlert Horn	12VDC	25	14
Sensor ea Sisteme H42 SpectrAlert Horn3	24VDC	42	37
Sensor ea Sisteme S1215 SpectrAlert Strobe	12VDC	159	133
Sensor ea Sisteme S121575 SpectrAlert Strobe	12VDC	182	168
Sensor ea Sisteme S2415 SpectrAlert Strobe3	24VDC	142	83
Sensor ea Sisteme S241575 SpectrAlert Strobe3	24VDC	132	76
Sensor ea Sisteme S2475 SpectrAlert Strobe3	24VDC	170	145
Sensor ea Sisteme S24110 SpectrAlert Strobe3	24VDC	220	169
Sensor ea Sisteme P1215 SpectrAlert Horn/Strobe	12VDC	173	144
Sensor ea Sisteme P121575 SpectrAlert Horn/Strobe	12VDC	196	179
Sensor ea Sisteme P2415 SpectrAlert Horn/Strobe3	24VDC	165	94
Sensor ea Sisteme P241575 SpectrAlert Horn/Strobe3	24VDC	177	111

Sensor ea Sisteme P2475 SpectrAlert Horn/Strobe3	24VDC	215	180
Sensor ea Sisteme P24110 SpectrAlert Strobe3	24VDC	265	214
Sensor ea Sisteme RP1215ADAARetrofit Strobe Plate	12VDC	200	170
Sensor ea Sisteme RP121575ADAARetrofit Strobe Plate	12VDC	240	255
Sensor ea Sisteme RP2415ADAARetrofit Strobe Plate	24VDC	90	75
Sensor ea Sisteme RP241575ADAARetrofit Strobe Plate	24VDC	120	93
Sensor ea Sisteme RP2475ADAARetrofit Strobe Plate	24VDC	200	170
Sensor ea Sisteme RP24110ADAARetrofit Strobe Plate	24VDC	245	210
Sensor ea Sisteme H24 SpectrAlert	24VDC	42	37
Sensor ea Sisteme S2415 SpectrAlertStrobe3	24VDC	142	83
Sensor ea Sisteme S241575 SpectrAlert Strobe3	24VDC	132	76
Sensor ea Sisteme S2475 SpectrAlert Strobe3	24VDC	170	145
Sensor ea Sisteme S24110 SpectrAlert Strobe3	24VDC	220	169
Sensor ea Sisteme S2415 SpectrAlert Horn/Strobe3	24VDC	165	94
Sensor ea Sisteme S241575 SpectrAlert Horn/Strobe3	24VDC	177	111
Sensor ea Sisteme S2475 SpectrAlert Horn/Strobe3	24VDC	215	180
Sensor ea Sisteme P24110 SpectrAlert Horn/Strobe3	24VDC	265	214
Sensor ea Sisteme S2415 SpectrAlertStrobe3	24VDC	142	83
Sensor ea Sisteme S241575 SpectrAlert Strobe3	24VDC	132	76
Hlokomela: 1) Liphanele tsa taolo tse fanang ka matla a Kopo e Khethehileng (FWR, Filtered) li tlameha ho sebelisa lisebelisoa tsa tsebiso, li-relay kapa litšepe tsa mamati tse thathamisitsoeng tafoleng ena. 2) Maqhubu ohle a ho Millamperes le boemo bo bobe ka ho fetisisa. 3) Nominal Operating voltage. 4) Sheba Litaelo tsa Tlhophiso bakeng sa tlhahisoleseling e eketsehileng. 5) Ikopanye le moetsi bakeng sa maqhubu.

Lethathamo la 6 Lisebelisoa tsa Tsebiso tse thathamisitsoeng ke UL

						Palo ea li-Detectors Ka Sebaka
Mohlala	Det. ID	Mofuta oa detector	Mohlala oa Motheo	ID ea motheo	Standby Current (uA)	PDRP-1001/ PDRP-1001A/ PDRP-1001E
Sensor ea Sisteme 1400	A	Ionization	n/a	n/a	100	20
Sensor ea Sisteme 1451	A	Ionization	B401B / B406B	A	120	15 / 1
Sensor ea Sisteme 1851DH	A	Ionization	DH1851DC	A	120	15
Sensor ea Sisteme 2400	A	Motlakase oa lifoto	n/a	n/a	120	15
Sensor ea Sisteme 2400AIT	A	Senepe / Isolated Thermal / Horn	n/a	n/a	120	1
Sensor ea Sisteme 2400AT	A	Senepe / Thermal / Horn	n/a	n/a	120	1
Sensor ea Sisteme 2400TH	A	Senepe / Thermal	n/a	n/a	120	15
Sensor ea Sisteme 2451	A	Motlakase oa lifoto	B401B / B406B	A	120	15 / 1
Sensor ea Sisteme 2451TH	A	Senepe / Thermal	B401B / B406B	A	120	15 / 1
Sensor ea Sisteme 2851DH	A	Motlakase oa lifoto	DH2851DC	A	120	15
Sensor ea Sisteme 1451DH	A	Ionization	EA-400	A	120	15
Sensor ea Sisteme 2451	A	Motlakase oa lifoto	EA-400	A	120	15
Sensor ea Sisteme 2300T	A	Senepe / Thermal	n/a	n/a	120	15
Sensor ea Sisteme 1800	A	Ionization	n/a	n/a	100	n/a
Sensor ea Sisteme 1851B	A	Ionization	B101B	A	120	n/a
Sensor ea Sisteme 1851B	A	Ionization	B107B	A	120	n/a
Sensor ea Sisteme 2800	A	Motlakase oa lifoto	n/a	n/a	120	n/a
Sensor ea Sisteme 2800TH	A	Senepe / Thermal	n/a	n/a	120	n/a
Sensor ea Sisteme 2851B	A	Motlakase oa lifoto	B101B	A	120	n/a
Sensor ea Sisteme 2851B	A	Motlakase oa lifoto	B107B	A	120	n/a
Sensor ea Sisteme 2851BTH	A	Senepe / Thermal	B101B	A	120	n/a
Sensor ea Sisteme 2851BTH	A	Senepe / Thermal	B107B	A	120	n/a
Sensor ea Sisteme 1151	A	Aionization	B401 / B110LP / B116LP	A	120	15 / 15 / 1
Sensor ea Sisteme 2151	A	Motlakase oa lifoto	B401 / B110LP / B116LP	A	120	15 / 15 / 1

Lethathamo la 7 UL le thathamisitsoeng, Li-Detectors tsa Mosi tsa Mehala e Mebeli bakeng sa Liphanele tsa Taolo ea Notifier

Sehlomathiso C: Litlhoko tse Khethehileng tsa NFPA

PDRP-1001/PDRP-1001A/PDRP-1001E e etselitsoe hore e sebelisoe khoebong, indastering, le lits'ebetsong tsa mekhatlo 'me e finyella litlhoko tsa tšebeletso tlas'a Melao ea Sechaba ea Tšireletso ea Mollo (NFPA) e hlalositsoeng sehlomathisong sena. Likarolo tse fokolang tsa sistimi tse hlokahalang bakeng sa ho latela maemo a nepahetseng a NFPA li thathamisitsoe ka tlase.

Sehlopha sa Taolo sa PDRP-1001/PDRP-1001A/PDRP-1001E e nang le boto e kholo ea taolo, khabinete (lebokose le ka morao le monyako), sesebelisoa se seholo sa phepelo le phepelo ea motlakase.

Libetri (sheba Sehlomathiso A bakeng sa Litlhoko tsa Matla a Standby).

Lisebelisoa tsa ho qala - e hokahane le e 'ngoe ea li-Circuits tsa sesebelisoa sa ho qala tsa phanele.

Lisebelisoa tsa Tsebiso - e hokahane le e 'ngoe ea li-control panel's Notification Appliance Circuits.

Releasing Devices – connected on one of the control panel’s Releasing Circuits.

Lisebelisoa tse ling tse latelang lia hlokahala bakeng sa ho latela maemo a NFPA a thathamisitsoeng ka tlase.

NFPA 72 Signaling Systems bakeng sa Tšebeletso ea Seteishene sa Bohareng

(Protected Premises Unit) TLHOKOMELISO• MOLEMO 911AC DACT* - bakeng sa ho hokela Seamoheli sa Seteishene se Bohareng kapa se Sirelelitsoeng
Setsi sa ho Fumana Meaho. Sesebelisoa sena se tlameha ho kenngoa joalo ka ha ho bontšitsoe ka tlase. Bakeng sa tlhahisoleseling e eketsehileng mabapi le 911AC, sheba tokomane 74-06200-005.

Likhokahano tsohle lipakeng tsa FACP le 911AC li tlameha ho ba ka har'a kotopo, bolelele bo ka tlase ho 20 ft (609.6cm) ka phapusing e le 'ngoe. Haeba NOTI•FIRE 911AC e sa kengoa ka har'a PDRP-1001/PDRP-1001A/PDRP-1001E maqhama ohle a tlameha ho ba conduit, bolelele bo ka tlase ho 20 ft. (609.6 cm) ka phapusing e le 'ngoe.

*Ts'ebeliso ena e sebelisang NOTI•FIRE 911AC ha e ea amoheloa ke FM.

Tlhokomeliso: Bakeng sa 911AC

• Boemo bo phahameng ba standby e tla ba 125 mA.
• Tlhokahalo ea Battery ea Standby: 24VDC, 7Amp-Hora-Max.
• PDRP-1001/PDRP-1001A/PDRP-1001E ha e loketse ho fetisoa ha lets'oao la taolo ho
  Setšoantšo sa DACT.

Ho sebelisa MS-5012 joalo ka DACT

1. Sheba buka ea MS-5012 bakeng sa lintlha tse ling.
2. Lenaneo la MS-5012 bakeng sa likopo tsa makhoba.
3. PDRP-1001/PDRP-1001A/PDRP-1001E ha e loketse ho fetisetsoa ha letšoao la tsamaiso ho DACT.

Sistimi ea Alamo ea Mollo e Thusang ea NFPA 72

Lihokelo tsohle li na le matla a fokolang 'me li laoloa. Sesebelisoa sena ha sea lokela phetisetso e arohaneng ea bolaodi ba sefafatsi kapa maemo a mathata.
Tlhokomeliso: Boholo ba khanyetso ea loop bo lumelletsoeng bakeng sa mohala ho tloha phanele ea taolo ho ea Lebokoseng la Masepala ke 3 ohms.

Sistimi ea Alamo ea Mollo ea NFPA 72 ea Remote Station

E reretsoe ho hokela potoloho ea polarity ea seteishene se hole se amohelang yuniti e nang le lintlha tse tsamaellanang. Likhokahano tsohle li na le matla a fokolang 'me li hlokometsoe ntle le reverse polarity loop. Tlhokomelo ea loop ke boikarabello ba moamoheli.

Letlapa la ho rarolla mathata

Tiisetso e Lekanyelitsoeng

Sensor ea Sisteme® e fana ka tumello ea hore lihlahisoa tsa eona li hloke bofokoli ba thepa le moetso oa eona bakeng sa likhoeli tse leshome le metso e robeli (18) ho tloha ka letsatsi la tlhahiso, tlas'a ts'ebeliso le ts'ebeletso e tloaelehileng. Lihlahisoa ke letsatsi stamped ka nako ea ho etsoa. Boitlamo bo le bong le bo ikhethileng ba Sensor ea Sisteme® ke ho lokisa kapa ho chencha, ka boikhethelo, mahala bakeng sa likarolo le mosebetsi, karolo efe kapa efe e nang le bothata ka thepa kapa moetso tlas'a ts'ebeliso le ts'ebeletso e tloaelehileng. Bakeng sa lihlahisoa tse seng ka tlase Sensor ea Sisteme® letsatsi la tlhahiso-stamp taolo, tiisetso ke likhoeli tse leshome le metso e robeli (18) ho tloha letsatsing la theko ea pele ka Sensor ea Sisteme® mofani oa thepa ntle le haeba litaelo tsa ho instola kapa lethathamo la libuka li beha nako e khuts'oane, moo ho tla sebetsa nako e khuts'oane. Tiisetso ena ha e na thuso haeba sehlahisoa se fetotsoe, se lokisoa kapa se sebeletsoa ke mang kapa mang ntle le Sensor ea Sisteme® kapa barekisi ba eona ba lumelletsoeng kapa haeba ho na le ho hloleha ho boloka lihlahisoa le litsamaiso tseo ba sebetsang ho tsona ka mokhoa o nepahetseng le o sebetsang. Haeba ho na le bofokoli, mohala Lefapha la Tokiso ea Sensor®, RA #_                                                                                    , 3825 Ohio Avenue, St. Charles, IL 60174. Ka kopo, kenyelletsa molaetsa o hlalosang ho se sebetse hantle le sesosa se belaelloang sa ho hloleha.

Sengoliloeng sena se na le tiisetso e le 'ngoe feela e entsoeng ke Sensor ea Sisteme® mabapi le lihlahisoa tsa eona. Sensor ea Sisteme® ha e emele hore lihlahisoa tsa eona li tla thibela tahlehelo leha e le efe ka mollo kapa ka tsela e 'ngoe, kapa hore lihlahisoa tsa eona maemong 'ohle li tla fana ka tšireletso eo li kentsoeng kapa li reretsoeng ho eona. Moreki o amohela seo Sensor ea Sisteme® ha se inshorense 'me ha e nke kotsi ea tahlehelo kapa ts'enyehelo kapa litšenyehelo tsa tšitiso efe kapa efe, lipalangoang, tšenyo, tšebeliso e mpe, tlhekefetso, kotsi kapa ketsahalo e tšoanang.

TS'ELISO TS'OANELO® HA E FE TIISETSO, E BONTŠHILENG KAPA E BONANG, EA THEKISO, HO TSHWANELA BAKENG SA MORERO OFE kapa O Mong, KAPA TSE LING TSE EKETSEHILENG KA NTLE HO TLHALOSO SEFAHLEHO MONA. TLAS'A MAEMO HA HO MAEMO A TLA TS'ELISO TS'OANELO® E BA MOIKARABELLO WA TAHLEHELO KAPA TŠENYEHO EFE KAPA EFE EA MORUO, KA TOKA, KA TSATSAHALO KAPA E TLASANG, E TSOANG KA NAKO EA SEBEDISO, KAPA HO HLOKA HO SEBELISA. TS'ELISO TS'OANELO® LITŠOANTŠISO. HO EKETSEHILENG, TS'ELISO TS'OANELO® E KA SE KE UA BA MOIKARATO BAKENG SA TŠEBELETSO EA MOTHO KAPA LEFU LE KA TLANG HO HLAHALA MOKHOA OA, KAPA KA BAKA LA HO SEBELISA LIHLAHISO TSA LINTHO TSEO, KA HO SEBELISA KA HO SEBELISA KA HO SEBELISA KA HO SEBELISA HA HAO, KA HO SEBELISA KAPA MOSEBETSI OA LITŠOANTŠISO.

Tiisetso ena e nka sebaka sa liwaranti tsohle tse fetileng mme ke eona feela tiisetso e entsoeng ke Sensor ea Sisteme®. Ha ho keketseho kapa phetoho, e ngotsoeng kapa ka mantsoe, ea tlamo ea tiisetso ena e lumelletsoeng.

Sensor ea Sisteme
3825 Ohio Avenue, St. Charles, IL 60174 1-800-SENSOR2 Fax: 630-377-6495

Litokomane / Lisebelisoa

SYSTEM SENSOR PDRP-1001 Phanele ea Taolo ea Phallo ea Moroallo [pdf] Bukana ea Mosebelisi PDRP-1001 Phanele ea Taolo ea Moroallo, PDRP-1001, Panel ea Taolo ea Moroallo, Panel ea Taolo ea Preaction

Litšupiso

• Bukana ea Mosebelisi