SuperLightingLED WF311 WiFi DMX Master Controller

Litlhaloso tsa Sehlahisoa

• Lebitso: WiFi-DMX Master Controller
• Mohlala: WF311

Kakaretso ea Sehlahisoa

Taolo ena ke WiFi ho ea ho DMX controller e ikemetseng e ikemetseng ke k'hamphani ea rona. Mesebetsi ea eona ea mantlha ke ho fifala ha liteishene tse 512, ho beha le ho letsa ha liketsahalo le mekhoa e bonolo ea matla ho phanele ea mobile ea APP, le taolo ea mabone bakeng sa mekoallo, s.tages, libaka le libaka tse ling libakeng tse ling tse nyane. Letšoao la kantle la DMX le lona le ka hokeloa ho chencha lipakeng tsa DMX tsa kahare le kantle ka sesebelisoa ho molaoli. Likarolo tse kholo tsa sehlahisoa ke tse latelang:

Tekheniki Parameters

1. Music mode, 170 RGB pixels of microphone or audio signal jump with the music;
2. 512 channels slide dimming, you can also select the overall brightness dimming of the channel brightness;
3. 512 channel static brightness scene editing and calling;
4. 512 channel dynamic mode editing and calling;
5. To switch the output signal, switch the internal and external DMX signal through the switch interface;
6. Switch between the direct connection and routing modes of the mobile phone and the controller;

 Software technical parameters
Control software：

1. Lebitso: DMX512
2. Runtime platform: IOS and Android system
3. Language: Automatically switch between Chinese and English according to the mobile phone software language system
4. Category: communications
5. Tse ling: Mahala, ha ho li-plug-ins

Controller technical parameters

1. Sebetsa voltage: DC12V-24V
2. Mocheso o sebetsang: -20-60 ℃
3. Working Power consumption: less than 1.5W
4. Sephetho: Letšoao la DMX512 (aterese 1-512)
5. Protocol ea puisano: Art-net, DMX512
6. Boima ba 'mele: 333g
7. Boima ba 'mele: 625g
8. Boemo ba ka ntle: L146*W73*H38 mm
9. Boima ba ho paka: L252*W180*H60 limilimithara

Tlhaloso ea sebopeho sa taolo

Boemo ba sesupo le taelo ea sebopeho se ka pele

NO.	Tšoaea	Phatlalatso ea mosebetsi
1	Matla	Power indicator light, long-time bright shows power supply normally
2	KA NAKO/TS'O	Leseli la mohloli oa leseli la DMX, le tima le emela lets'oao la kahare la DMX, le butswe the light represents the external DMX signal, flashing represents the mobile APP instruction issued
3	AP/STA	Hotspot mode or routing mode, AP mode on, STA mode off;

4	DMX	DMX signal output indicator light, flashing indicates DMX signal output
5	Mic	Hlooho ea molumo e hahiloeng kahare
6	Audio	External audio port, external audio signal is preferred

Hlokomela: If the device has just been powered on, all the indicator lights are on at the same time, indicating that the device is in preparation

Back-end interface description

Monate: Mode switch, reset button

• Mode switching: press the button to switch mode to switch 8 static scenes, 6 dynamic scenes and A total of 15 modes for voice control;
• Reset operation: long press and hold for more than 5 seconds, release the IN/OUT light flashes 4 times, restart the factory setting after power off (it will take about 1 minute to return to normal after power on), WIFI module will switch to AP mode, WIFI will be on, connect WIFI can search the device.

DMX OUT: DMX signal output card mouth;
DMX INT: external DMX signal input card mouth;
Fetoha: internal and external DMX signal switching port, K short GND to forward external input DMX signal;

Litaelo tsa ho sebelisa mobile APP "WF-DMX"

1. Kakaretso
   The mobile APP software “WF-DMX” is the control APP used by the controller, and the APP can edit DMX signals of 512 channels. Users can edit and invoke 8 static scenes and 6 dynamic scenes.
2. Litaelo
   1. installation “WF – DMX”
      The software can be installed through the Android or iOS download provided in the CD, and the APP is called WF-DMX.
   2. Connect WIFI network and device
      First of all, the independent WiFi connected to the controller is used. Generally, the SSID is WF311-XXXX. Then open the APP to search for devices, and click on the device to be controlled (tick) to start the control.
   3. Litlhophiso tsa router
      Click the router Settings and click the search icon, the input box of WIFI name and password will appear. Please make sure that the password is correct, so as to avoid the need to reset the device and rejoin later. WIFI of the device will be closed after this setting, and only the WIFI can be connected when controlling the device.
   4. Scene jump time
      This function represents the time required for color transition during static scene switching from 0 to 30 seconds.
   5. Taolo ea Channel
      1. In this page, parameters of each channel can be set directly. Before setting, light the lightbulb icon in the top left corner, and then select the channel (red is the selected state) to adjust the output parameters
      2. The top right side lights up the music icon to indicate “Music Mode”.
         Music mode: devices on the bus beat every 3 channels as an RGB pixel, according to the music rhythm.

Static Scenes
Tobetsa nako e telele letšoao la ketsahalo ho le reha bocha. Tobetsa hukung e kaholimo ho le letona ho kenya boemo ba ho hlophisa ketsahalo. Kamora ho hlophisa liparamente tse tsitsitseng, e hloka ho bolokoa

Dynamic scene
The editing method of dynamic scene is similar to that of static scene. Click the upper right corner to enter the editing interface, and long press the icon to rename it. However, there are a few points that need to be noted:

1. Add frame: dynamic scene needs to have a change frame to express the next changed scene. “+” in the lower right corner of the editing interface means to add and enter the configuration of the next frame. (The bottom operation is “return to previous frame”, “delete frame”, “add frame” in order)
2. Hold: Indicates how long the state of this frame lasts (seconds) before entering the next frame, and the output state does not change within the state of this frame.
3. Jump: represents the time (seconds) required for the transition (gradient) of this frame state to the next frame, and the output state will change in the continuous state.
4. Optional unit of time: Click the unit to pop up the unit selection box, there are three units of time to choose, MS, S, M.

Exit routing mode
Batla leqephe la sesebelisoa, tobetsa nako e telele nomoro ea sesebelisoa ho khetha ho tsoa mokhoeng oa ho tsamaisa.

 Controller built-in mode table

NO.	Mekhoa	NO.	Mekhoa
1	Sebaka sa Static 1	9	Dynamic scene 1
2	Sebaka sa Static 2	10	Dynamic scene 2
3	Sebaka sa Static 3	11	Dynamic scene 3
4	Sebaka sa Static 4	12	Dynamic scene 4
5	Sebaka sa Static 5	13	Dynamic scene 5
6	Sebaka sa Static 6	14	Dynamic scene 6
7	Sebaka sa Static 7	15	Music voice control
8	Sebaka sa Static 8

Setšoantšo se tloaelehileng sa khokahanyo

 APP controls the internal DMX signal wiring mode

Switch to external DMX signal wiring mode

FAQs

• Q: How to switch between internal and external DMX signals?
  A: You can switch between internal and external DMX signals through the switch on the controller.
• Q: What are the supported runtime platforms for the control software?
  A: The runtime platform includes iOS and Android systems.
• Q: How to reset the controller to factory settings?
  A: Long press and hold the reset button for more than 5 seconds, then release. The IN/OUT light will flash 4 times, indicating a reset to factory settings.

Litokomane / Lisebelisoa

SuperLightingLED WF311 WiFi DMX Master Controller [pdf] Buka ea Taelo WF311 WiFi DMX Master Controller, WF311, WiFi DMX Master Controller, Master Controller, Controller

Litšupiso

• Bukana ea Mosebelisi