D5-P, D5-E
5 Channel Constant Voltage DMX512 & RDM Decoder

DMX512 5 Channel Constant Voltage le RDM Decoder

• Latela melaoana e tloaelehileng ea DMX512.
• Pontšo ea linomoro tsa dijithale, seta aterese ea ho qala ea DMX ka likonopo.
• Ts'ebetso ea RDM e ka khona ho fumana puisano lipakeng tsa master ea DMX le decoder.
  Bakeng sa mohlalaample, aterese ea DMX decoder e ka hlophisoa ke master console ea DMX.
• 16bit (maemo a 65536) /8bit (maemo a 256) boemo bo bohlooho bo ka khethoang.
• PWM frequency 250/500/1000/2000/4000/8000/16000/32000Hz selectable.
• Logarithmic kapa linear dimming curve e ka khethoa.
• Mocheso o fetelletseng / boima bo feteletseng / Ts'ireletso ea potoloho e khuts'oane, hlaphoheloa ka bohona.
• D5-P e na le likou tsa matšoao a Green terminal DMX, D5-E e na le likou tsa matšoao tsa RJ-45 DMX.

Tekheniki Parameters

Kenyeletso le Sephetho

Keletso voltage	12-48VDC
Kenya hona joale	20.5A
Sephetho voltage	5x(12-48)VDC
Sephetho sa hajoale	5CH,4A/CH
Matla a hlahisang	5x(48-192)W
Mofuta oa tlhahiso	Kamehla voltage

Tiisetso le Tshireletso

Tiisetso	5 lilemo
Tshireletso	Reverse polarity, Over-heat Over-load, Short circuit

Tikoloho

Mocheso oa ts'ebetso	Ta: -30₀⁰ C ~ +55⁰ C
Thempereichara ea boholo (Boholo.)	Tc: +75⁰C
Lintlha tsa IP	IP20

Tšireletseho le EMC

EMC e tloaelehileng	EN IEC 55015/EN IEC 61547
Tekanyetso ea polokeho	EN 61347-1/-2 EN 62493
Cortication	CE RoHs

Sephutheloana

Boholo	L178 x W50 x, x H38mm
Boima bo felletseng	0.295kg

Mechanical Structures le Installations

Setšoantšo sa WiringHlokomela:

1. Letšoao la DMX ampLifier ea hlokahala haeba ho hoketsoe li-decoder tse fetang 32, kapa ho sebelisoa mats'oao a malelele amplification ha ea lokela ho feta makhetlo a 5 ka ho tsoelang pele.
2. Haeba phello ea ho khutlisa e etsahala ka lebaka la mohala o molelele oa lets'oao kapa boleng bo bobe ba mohala, ka kopo leka ho hokela 0.25W 90-120Ω terminal resistor qetellong ea mohala o mong le o mong oa lets'oao oa DMX.
3. Ha o bonts'a OLA, alamo e tletse haholo. Ha o hlahisa OHA, alamo ea mocheso o feteletseng.

Tshebetso

Litlhophiso tsa parameter ea sistimi

• Long press M and ◀ key in the same time for 2s, prepare for setup system parameter: grey level, output PWM Frequence, output brightness curve, default output level, automatic blank screen. short press M key to switch ve item.
• Grey level: short press ◀ or ▶ key to switch 8bit(”b08″) or 16 bit(”b16″). choose 16 bit if the DMX master support 16 bit.
• Output PWM frequency: short press ◀ or ▶ key to switch 250Hz(”F02″), 500Hz(”F05″), 1000Hz(”F10″), 2000Hz(”F20″), 4000Hz(”F40″), 8000Hz(”F80″), 16000Hz(”F16″) or 32000Hz(”F32″). Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No ickers for video). When setting the PWM frequency > 8000Hz, the output current per channel needs to be reduced (5x3A@12-48V at 16000Hz or 32000Hz).
• Output brightness curve: short press ◀ or ▶ key to switch linear curve(”C-L”) or logarithmic curve(”C-E”).
• Default output level: set output level when no DMX input signal. short press ◀ or ▶ key to switch maintain DMX output(”d- -“) or output default level (“d00” to “dFF”, 0-100%), long press ◀ or ▶ key to change output default level.
• Automatic blank screen: short press ◀ or ▶ key to switch enable (”bon”) or disable(”boF”) automatic blank screen.
• Tobetsa nako e telele konopo ea M bakeng sa 2s kapa timeout 10s, tlohela tlhophiso ea paramethara ea sistimi.
  Tlhokomeliso: Ntle le litlhophiso tsa ts'ebetso ea konopo ea letsoho, liparamente tse kaholimo li ka hlophisoa ke ts'ebetso ea RDM.

Mokhoa oa DMX

• Tobetsa hakhutšoanyane M key, ha o bonts'a 001~512, kenya mokhoa oa DMX.
• Press ◀ or ▶key to change DMX decode start address(001~512),long press for fast adjustment.
• Haeba ho na le kenyo ya letshwao la DMX, e tla kena mokgweng wa DMX ka boyona.
•  DMX dimming: Each D5-P/D5-E DMX decoder occupy 5 DMX address when connecting the DMX console.
  Bakeng sa mohlalaample, aterese ea ho qala e sa fetoheng ke 1, kamano ea bona e tsamaellanang ka foromo:

DMX Console	Sephetho sa Decoder ea DMX
CH1 0-255	CH1 PWM 0-100% (LED R)
CH2 0-255	CH2 PWM 0-100% (LED G)
CH3 0-255	CH3 PWM 0-100% (LED B)
CH4 0-255	CH4 PWM 0-100% (LED W1)
CH5 0-255	CH5 PWM 0-100% (LED W2)

Mokhoa oa ho itlhahloba

• Kenya mokhoa oa ho itlhahloba ha feela lets'oao la DMX le khaotsoe kapa le lahlehile.
• Tobetsa hakhutšoanyane M key, ha o bonts'a L-1~L-6, kenya mokhoa oa ho itlhahloba.
• Press ◀ or ▶ key to change mode number(L-1~L-6).
• Self-test mode include ve channels light up separately or synchronously.

Khutlisa litlhophiso tsa kamehla tsa feme

• Tobetsa nako e telele ◀ le ▶ konopo bakeng sa 2s, khutlisetsa parameter ea kamehla ea feme, bonts'a"RES".
• Factory default parameter: DMX decode mode, DMX decode start address is 1, 8 bit grey level, 2000Hz PWM Frequence output, logarithmic brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.

Dimming Curve Setting

Tlhahlobo e sa sebetseng hantle le ho rarolla mathata

Ho se sebetse hantle	Lisosa	Ho batle phoso
Ha ho khanya	1 .No power. 2.Khokahano e fosahetseng kapa e sa sireletsehang.	1.Check the power. 2.Check the connection.
Mmala o fosahetseng	1 .Wrong connection of R/G/B/W1 /W2 wires. 2.DMX decode address error.	1.Reconnect R/G/B/W1 /W2 wires. 2.Set correct decode address.
Ho se leka-lekane pakeng tsa ka pele le ka morao, ka voltaglerotholi	1 .Output cable is too long. 2.Wire bophara e nyane haholo. 3.Overload beyond power supply capability. 4.Overload beyond controller capability.	1.Reduce cable or loop supply 2.Change wider wire. 3.Replace higher power supply. 4.Add power repeater.

Litokomane / Lisebelisoa

MiBOXER DMX512 5 Channel Constant Voltage le RDM Decoder [pdf] Buka ea Taelo D5-P, D5-E, DMX512 5 Channel Constant Voltage le RDM Decoder, DMX512, 5 Channel Constant Voltage le RDM Decoder, Constant Voltage le RDM Decoder, RDM Decoder

Litšupiso

• Bukana ea Mosebelisi