MiBOXER DMX512 3 Channel Constant Voltage le Bukana ea Mong'a Decoder ea RDM

RDM function can realize intercommunication between the DMX master and decoder. For example, the DMX decoder address can be set by the DMX master console.
PWM frequency 250/500/1000/2000/4000/8000/16000/32000Hz selectable.
Logarithmic kapa linear dimming curve e ka khethoa.
Stand-alone RGB mode and 3-channel dimmer mode are selectable, which can be controlled by buttons with built-in programs, instead of a DMX signal.

Terminal e tala, XLR5 le RJ45 port DMX signal input.
Over-heat / Short circuit protection, recovers automatically.

Tekheniki Parameters

Mechanical Structures le Installations

Setšoantšo sa Wiring

Hlokomela

Letšoao la DMX amplifier is needed if more than 32 decoders are connected, oif r use longer signal line is used, signal amplification ha ea lokela ho feta makhetlo a 5 ka ho tsoelang pele.
If the recoil effect occurs because of a longer signal line or bad line quality, please try to connect a 0.25W 90-120Ω terminal resistor at the end of each DMX signal line.

Tshebetso

Litlhophiso tsa parameter ea sistimi

Long-press M and the ◀ key at the same time for 2s, prepare for the setup system parameter: grey level, output PWM frequency, output brightness curve, default output level, and automatic blank screen. Press the M key to switch to have item.
Grey level: short press ◀ or ▶ key to switch 8bit(”b08”) or 16 bit(”b16”). Choose 16-bit if the DMX master supports 16-bit.

Output PWM frequency: short press ◀ or ▶ key to switch 2250Hz(“F02”), 500Hz(“F05”), 1000Hz(“F10”), 2000Hz(“F20”), 4000Hz(“F40”), 8000Hz(“F80”), 16000Hz(“F16”) or 32000Hz(“F32”). Higher PWM frequency will cause lower output current, higher power noise, but more suitable for camera(No sicker for video).
When PWM frequency > 8000Hz, it is necessary to reduce the output current per channel (3x6A@12-24V and 3x5A@36-48V at 16000Hz; 3x4A@12-24V and 3x3A@36-48V at 32000Hz).
Output brightness curve: short-press press ◀ or ▶ key to switch linear curve(”C-L”) and the logarithmic curve(”C-E”).

Default output level: set the output level when no DMX input signal. Short-press the ◀ or ▶ key to switch between maintaining DMX output(”d–”) or output default level(“d00” to “dFF”, 0-100%), long-press the ◀ or ▶ key to change output default level.
Automatic blank screen: short-press the ◀ or ▶ key to switch enable (”bon”) or disable(”boF”) automatic blank screen.

Long-press press M key for 2s or timeout 10s, quit system parameter setting.
Hlokomela: In addition to manual button operation settings, the above system parameters can also be set by the RDM function.

Mokhoa oa DMX

Press the M key when the display shows 001~512, enter DMX mode.

Press the ◀ or ▶ key to change the DMX decode start address(001~512), long-press for fast adjustment.
If there is a DMX signal input, it will enter DMX mode automatically.

DMX Dimming: Each D3-XE DMX decoder occupies 3 DMX addresses when connecting to the DMX console. For example, the default start address is 1, and its corresponding relationship in the form

DMX Console	Sephetho sa Decoder ea DMX
CH1 0-255	CH1 PWM 0-100% (LED R)
CH2 0-255	CH2 PWM 0-100% (LED G)
CH3 0-255	CH3 PWM 0-100% (LED B)

Mokhoa o ikemetseng oa RGB

Enter stand-alone RGB mode only when the DMX signal is disconnected or lost.

Press the M key short when the display shows P01~P30, enter stand-alone RGB mode.
Press the ◀ or ▶ key to change the dynamic mode number(P01~P30).

Mokhoa o mong le o mong o ka fetola lebelo le khanya.
Long-press press M key for 2s, prepare for setup mode speed and brightness. Press the M key to switch two items.
Press the ◀ or ▶ key to setthe value of each item.

Lebelo la mokhoa: lebelo la boemo ba 1-10 (S-1, S-9, SF).
Khanya ea mokhoa: khanya ea boemo ba 1-10(b-1, b-9, bF).
Long-press press M key for 2s, or timeout 10s, quit setting.

Boemo ba dimmer bo ikemetseng

Kenya mokhoa o ikemetseng oa dimmer hafeela lets'oao la DMX le khaotsoe kapa le lahlehile.

Press the M key when dthe display shows L-1~L-8, enter stand-alone dimmer mode.
Press ◀the or ▶ key to change the summer mode number(L-1~L-8).

Mokhoa o mong le o mong oa dimmer o ka fetola khanya ea mocha ka mong.
Long-press press M key for 2s, prepare for setting up the three-channel brightness.
Press the M key to switch three channels (100~1FF, 200~2FF, 300~3FF). Pressthe ◀ or ▶ key to set the brightness value of each channel.

Long-press press M key for 2s, or timeout 10s, quit setting.

Restore the factory default parameter. Tobetsa nako e telele press ◀ and ▶ keys for 2s, restore the factory default parameters, and display” RES”.

Factory default parameter: DMX decode mode, DMX decode start address is 1, 8-bit grey level, 2000Hz PWM frequency output, logarithmic brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.

Dimming Curve Setting

Lethathamo la Liphetoho tsa RGB

Che.	Lebitso	Che.	Lebitso	Che.	Lebitso
P01	Bofubelu bo tsitsitseng	P11	Green strobe	P21	Bosehla bo bofubelu bo boreleli
P02	Botala bo tsitsitseng	P12	Blue strobe	P22	'Cyan e tala e boreleli
P03	Putsoa e tsitsitseng	P13	White strobe	P23	Bopherese bo boputsoa bo boreleli
P04	Bosehla bo tsitsitseng	P14	RGB strobe	P24	Botala bo bosoeu bo boreleli
P05	Cyan e sa fetoheng	P15	7 mebala strobe	P25	RGB+W e bonolo
P06	Bopherese bo tsitsitseng	P16	Bofubelu bo nyamela ka hare le ka ntle	P26	RGBW e bonolo
P07	Bosoeu bo tsitsitseng	P17	Botala bo nyamela ka hare le ka ntle	P27	RGBY e bonolo
P08	RGB e tlole	P18	Boputsoa bo nyamela kahare le kantle	P28	Bopherese bo bosehla ba cyan bo boreleli
P09	7 tlola ka mebala	P19	Bosoeu bo nyamela ka hare le ka ntle	P29	RGB e bonolo
P10	Strobe e khubelu	P20	RGBW e nyamela kahare le kantle	P30	6 mmala o boreleli

Tlhahlobo e sa sebetseng hantle le ho rarolla mathata

Ho se sebetse hantle	Lisosa	Ho batle phoso
Ha ho khanya	1. Ha ho matla. 2. Khokahano e fosahetseng kapa e sa sireletsehang.	1. Hlahloba matla. 2. Sheba khokahano.
Mmala o fosahetseng	1. Wrong connection of R/G/B wires. 2. Phoso ea aterese ea DMX.	1. Reconnect R/G/B wires. 2. Set the correct decode address.
Matla a sa leka-lekaneng pakeng tsa ka pele le ka morao, ka voltaglerotholi	1. Mohala oa tlhahiso o telele haholo. 2. Wire diameter e nyane haholo. 3. Tlala e fetang matla a phepelo ea motlakase. 4. Moroalo o fetang matla a taolo.	1. Fokotsa phepelo ea cable kapa loop. 2. Fetola terata e pharaletseng. 3. Replace the higher power supply. 4. Eketsa motlakase oa matla.

FAQs

Do I need a DMX signal ampLifier ha o hokela li-decoder tse fetang 32?

Yes, a DMX signal amplifier is required if more than 32 decoders are connected or if using an overlong signal line. Signal amplification ha ea lokela ho feta makhetlo a 5 ka ho tsoelang pele.

How can I address recoil effects due to long signal lines or bad quality?

Connect a 0.25W 90-120 terminal resistor at the end of each DMX signal line to address recoil effects caused by long signal lines or poor quality.

Litokomane / Lisebelisoa

MiBOXER DMX512 3 Channel Constant Voltage le RDM Decoder [pdf] Buka ea Mong'a
DMX512 3 Channel Constant Voltage le RDM Decoder, DMX512, 3 Channel Constant Voltage le RDM Decoder, Constant Voltage le RDM Decoder, Moqtage le RDM Decoder, RDM Decoder

Litšupiso

Bukana ea Mosebelisi

MiBOXER DMX512 3 Channel Constant Voltage and RDM Decoder\

Litlhaloso

Likarolo tsa Bohlokoa