M5STACK StamPLC IoT Programmable Logic Controller
Litlhaloso
| Tlhaloso | Paramethara |
| Control Module | StampS3A contro1 module, e thehiloeng ho ESP32-S3FN8, e kenyelletsa 8MB Flash, 2.4GHz Wi-Fi, Bluetooth Low Energy (BLE) |
| LEHLANYA | 8MB |
| Lisebelisoa tsa Dijithale | 8 likanale tsa opto-isolated ditsitithale inputs, input voltagmefuta e fapaneng: DC 5 ~ 36V |
| Liphetho tsa dijithale | Liphetho tse 4 tsa likanale |
| Li-relay | AC 5A@250V,DC 5A@28V |
| Phepelo ea motlakase ea DC | e tšehetsa DC 6~36V@1A bophara ba voltage phepelo, sekhutlo sa matla sa DC: DC5521 basali, 5.5x 2.1mm(bohare-positive)Katoloso |
| n Lipuisano | GPIO.EXT segokanyimmediamentsi sa sebolokigolo, 2 Grove interfaces |
| Li-interface tsa puisano | Likhokahano tsa onboard PWR-CAN le PWR-485 |
| PWR-CAN Interface | XT30(2+2)PW-M |
| Sehokelo sa PWR-485 | HT3.96-4P |
| Pontšo | Pontšo ea mebala ea 1.14-inch (135 × 240 resolution), e tsamaisoa ke chip ea ST7789v2 |
| Contro1 & Tšebelisano | 1 konopo ea RESET/B00T, likonopo tse 3 tsa mosebelisi, buzzer |
| Polokelo ea Boitsebiso | Sekotjana sa karete ea Micro SD e hahiloeng kahare |
| Li-sensor | LM75 sensor ea mocheso, INA226 voltage/sensor ea hajoale,RTC(RX8130CE) |
| I/0 Bokhoni ba Mojaro oa Boemakepe | 2 × 8 segokanyimmediamentsi sa sebolokigolo:maximum 1oad bokgoni DC 4.76V @700mA, Grove port 1oad bokgoni:DC 4.81V e 700mA |
| Tšebeliso ea Matla | Boemo ba hona joale:(5V supp1y)DC 5V@21.60mA,(phepelo ea 12V)DC 12Ve15.22mA;Tlhahiso ea hona joale:(phepelo ea 5V)DC 5Ve93.89mA, (phepelo ea 12V)DC 12V@47.84mA |
| Mokhoa oa ho kenya | Ho hloa seporo sa DIN |
| Mocheso oa ho sebetsa | -10 ~ 50°C |
| Litekanyo tsa Sehlahisoa | 72.0×80.0×31.7mm |
| Boima ba Sehlahisoa | 139.4g |
| Litekanyo tsa sephutheloana | 102.0x94.0 x 37mm |
| Boima bo felletseng | 163.7g |
| Moetsi | M5Stack Technology Co., Ltd
Block A10, Expo Bay South Coast, Fuhai Street, Setereke sa Bao'an, Shenzhen, Chaena |
| Range ea khafetsa bakeng sa CE | 2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz |
| Boholo ba EIRP bakeng sa CE | BLE: 6.84dBm
2.4G Wi-Fi: 17.90dBm |
Litaelo tsa Tšebeliso ea Sehlahisoa
Qala ka Potlako
Ho qala ka Stam PLC ea hau, latela mehato ena:
SEKA Wi-Fi
- Matla ho Stam PLC ho sebelisa phepelo ea motlakase e fanoeng ea DC.
- Tobetsa konopo ea RESET/BOOT ho qala sesebelisoa.
- Kena ho li-setting tsa Wi-Fi sesebelisoa sa hau 'me u hlahlobe marang-rang a teng.
- Khetha marang-rang a nepahetseng a Wi-Fi ebe u kenya phasewete haeba ho hlokahala.
- Hang ha e se e hokahane, o ka qala ho sebelisa matla a puisano a se nang mohala a Stam PLC.
SEKANANG TŠEBELE
- Netefatsa hore Stam PLC e buletsoe 'me ea sebetsa.
- Kenya tšebetsong li-setting tsa Bluetooth sesebelisoa sa hau.
- Sheba lisebelisoa tsa Bluetooth tse fumanehang sebakeng seo.
- Khetha Stam PLC lethathamong la lisebelisoa tse sibollotsoeng ho theha khokahano ea BLE.
- Joale o ka sebelisa tšebetso ea BLE bakeng sa phetiso le taolo ea data.
TLHOKOMELO
Stam PLC ke IoT programmable logic controller e etselitsoeng boiketsetso ba indasteri le ho lebela hole. Sehlahisoa se thehiloe ho StampS3A control module, e sa faneng feela ka matla a ts'ebetso e matla empa hape e fana ka khokahanyo e sebetsang ea waelese. Mabapi le taolo, Stam PLC e fana ka lisebelisoa tsa dijithale tse 8 tse ikhethileng le liphetho tse 4 tsa relay (tse tšehetsang meroalo ea AC le DC), hammoho le
Boema-kepe ba GPIO.EXT le li-interfaces tsa 2 Grove, ho etsa hore ho kopanngoa ha li-sensor tse fapaneng le li-actuator li be bonolo ebile li ka tšeptjoa. Ho sa le joalo, ka li-interfaces tsa onboard PWR-CAN le PWR-485, sesebelisoa se ka kopanngoa ka mokhoa o se nang moeli ho marang-rang a liindasteri tsa fieldbus, ho nolofalletsa phetisetso ea data e hōle le taolo e bohareng.
Bakeng sa ho sebelisana le mochine oa batho, sehlahisoa se na le pontšo ea mebala ea 1.14-inch, konopo ea RESET / BOOT, likonopo tsa 3 tsa mosebedisi, le buzzer, e leng se thusang ho hlophisa parameter ea nako ea sebele le ho hlahloba maemo, 'me e ka hlokomelisa basebelisi ha ho e-na le liphoso. Ho mamella maemo a thata a indasteri, Stam PLC e ts'ehetsa palo e kholotage input (DC 6–36V) mme e etselitsoe ho kenya seporo sa DIN ho netefatsa ho kengoa ho sireletsehileng; sekotjana sa karete ea Micro SD se hahelletsoeng ka hare se thusa ho boloka data le liapdeite tsa firmware.
Ntle le moo, sistimi ea eona ea ho lekola tikoloho e kopanya sensor ea mocheso oa LM75 le INA226 voltage / sensor ea hona joale bakeng sa maikutlo a nako ea sebele mabapi le ts'ebetso ea lisebelisoa, ha module ea RTC (RX8130CE) e tiisa hore nako e nepahetseng ea ho lumellana le ho rekota log. Firmware ea feme e kenya data ka bo eona sethaleng sa leru sa M5's EZDATA, e hlahisa maqephe a ho beha leihlo le ho fa basebelisi phihlello le taolo ea maru e hole. Sehlahisoa sena se loketse liindasteri tsa boiketsetso, ho lekola hole, tlhahiso e bohlale, le lits'ebetso tse ling.
Stam PLC
Bokhoni ba Puisano
- Molaoli ea ka Sehloohong: ESP32-S3FN8 (StampS3A control module)
- Puisano e Se nang Waele: Wi‑Fi (2.4 GHz) le Bluetooth Low Energy (BLE)
- CAN Bus: Sehokelo sa Onboard PWR-CAN bakeng sa puisano e tšepahalang ea data ea indasteri, RS-485:
- Onboard PWR-485 interface e tšehetsang taolo e hole ka protocol ea Modbus RTU
processor le Tshebetso
- Mohlala oa processor: Xtensa LX7 dual-core (ESP32-S3FN8)
- Bokhoni ba polokelo: 8MB Flash
- Makhetlo a Ts'ebetso: Ho fihla ho 240 MHz ho dual-core 32-bit LX7 microprocessor
Pontsho le Kenyo
- Pontšo: Pontšo ea TFT ea mebala ea 1.14-inch bakeng sa ho lekola paramethara ea nako ea nnete
- Likonopo: Konopo e 1 ea RESET/BOOT hammoho le likonopo tse 3 tsa mosebelisi bakeng sa taolo le tlhophiso. Buzzer:
- E hahelletsoeng ka har'a buzzer bakeng sa litlhokomeliso tsa molumo le litsebiso
- RGB LED: LED ea RGB e kopantsoeng bakeng sa maikutlo a matla a pono
Lithakhisa tsa GPIO le li-interfaces tse ka khonehang
- GPIO Pins: E fana ka lithakhisa tse ngata tse lokisehang tsa GPIO ('mapa o hlakileng o fumaneha litokomaneng)
- Katoloso ea li-interfaces:
- 2 Grove interfaces bakeng sa khokahano e bonolo ea sensor le actuator
- Sebopeho sa GPIO.EXT bakeng sa khokahanyo e eketsehileng
- Slot ea karete ea Micro SD bakeng sa polokelo ea data le liapdeite tsa firmware
Ba bang
- Li-Onboard Interfaces: Sehokelo sa Mofuta-C bakeng sa mananeo, phepelo ea motlakase, le likhokahano tsa serial
- Boima ba 'Mele: 72.0 × 80.0 × 31.7 limilimithara tse nang le moralo oa seporo sa DIN, se loketseng maemo a thata a indasteri.
- Kenyeletso ea Matla: Wide voltage input ho tloha DC 6–36V
- Li-Sensors tse Kopantsoeng: E kenyelletsa sensor ea mocheso oa LM75, INA226 voltage/sensor ea hajoale, le RTC (RX8130CE) bakeng sa khokahano e nepahetseng ea nako le ho rekota rekoto
- Liphetho tsa Relay: 4-channel relay e ts'ehetsa AC 5A @ 250V / DC 5A @ 28V Opto-Isolated Digital Inputs: Likanale tse 8 tse etselitsoeng ho ts'ehetsa lisebelisoa tsa DC 5-36V bakeng sa matšoao a bolokehileng a acq.
Boholo ba Mojule
PHAKAMATSO
Pele o etsa mohato ona, sheba sengoloa sehlomathisong sa ho qetela: Ho kenya Arduino.
Hatisa lintlha tsa WiFi
- Bula Arduino IDE (Sheba ho https://docs.m5stack.com/en/arduino/arduino_ide bakeng sa tataiso ea ho kenya bakeng sa boto ea nts'etsopele le software)
- Khetha boto ea Module ea ESP32S3 DEV le boema-kepe bo lumellanang, ebe u kenya khoutu.e
- Bula sebali sa serial ho bonts'a WiFi e hlahlobiloeng le tlhahisoleseling ea matla a lets'oao.
PHAKAMATSO
Pele o etsa mohato ona, sheba mongolo sehlomathisong sa ho qetela: Ho kenya Arduin.
Hatisa lintlha tsa BLE
- Bula Arduino IDE (Sheba ho https://docs.m5stack.com/en/arduino/arduino_ide bakeng sa tataiso ea ho kenya bakeng sa boto ea nts'etsopele le software)
- Khetha boto ea ESP32S3 DEV Module le boema-kepe bo lumellanang, ebe u kenya khoutu.
- Bula sebali sa serial ho bonts'a BLE e hlahlobiloeng le tlhaiso-leseling ea matla.
Tlhokomeliso ea FCC
Tlhokomeliso ea FCC:
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC.
Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi, le
- Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
TLHOKOMELISO EA BOHLOKOA:
Hlokomela: Thepa ena e lekoa 'me e fumanoe e lumellana le meeli ea sesebelisoa sa digital sa Sehlopha sa B, ho latela karolo ea 15 ea Melao ea FCC. Meeli ena e etselitsoe ho fana ka tšireletso e utloahalang khahlanong le tšitiso e kotsi mohahong oa bolulo. Thepa ena e hlahisa, e sebelisa, 'me e ka khantša matla a maqhubu a seea-le-moea, 'me haeba e sa kengoa le ho sebelisoa ho latela litaelo, e ka baka tšitiso e kotsi likhokahanong tsa radio. Leha ho le joalo, ha ho na tiiso ea hore tšitiso e ke ke ea etsahala setsing se itseng.
Haeba sesebelisoa sena se baka tšitiso e kotsi ea seea-le-moea kapa kamohelo ea thelevishene, e ka lekanyetsoang ka ho tima le ho tima sesebelisoa, mosebelisi o khothalletsoa ho leka ho lokisa tšitiso ka e le 'ngoe kapa tse ling tsa mehato e latelang:
- Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
- Eketsa karohano pakeng tsa thepa le moamoheli.
- Hokela lisebelisoa sebakeng sa seketsoana se fapaneng le seo moamoheli a hokahaneng le sona.
- Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.
Phatlalatso ea Phaello ea Mahlaseli a FCC
Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a FCC e behiloeng bakeng sa tikoloho e sa laoleheng. Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20cm lipakeng tsa radiator le 'mele oa hau.
Ho kenya Arduino
Ho kenya Arduino IDE (https://www.arduino.cc/en/Main/Software)
Tobetsa ho etela ofisiri ea Arduino website, 'me u khethe sephutheloana sa ho instola hore sistimi ea hau ea ts'ebetso e jarolloe.
Ho kenya Tsamaiso ea Boto ea Arduino
- Motsamaisi oa Boto URL e sebelisoa ho supa lintlha tsa boto ea nts'etsopele bakeng sa sethala se itseng. Ho menu ea Arduino IDE, khetha File -> Likhetho
- Kopitsa tsamaiso ea boto ea ESP URL ka tlase ho Motsamaisi oa Boto ea Tlatsetso URLs tšimo, 'me u boloke. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
- Ka lehlakoreng le leng, khetha Mookameli oa Boto, batla ESP, ebe o tobetsa Kenya.
- Ka lehlakoreng le leng, khetha Mookameli oa Boto, batla M5Stack, ebe o tobetsa Kenya.
Ho latela sehlahisoa se sebelisitsoeng, khetha boto ea ntlafatso e tsamaellanang tlasa Lisebelisoa -> Boto -> M5Stack -> {ESP32S3 DEV Module board}.
- Hokela sesebediswa khomphuteng ya hao ka thapo ya data ho kenya lenaneo.
Lipotso Tse Botsoang Hangata
Ke eng e khothaletsoang matla a ho sebetsatagna bakeng sa Stam PLC?
The khothaletsoang matla a ho sebetsa voltage pakeng tsa DC 6V ho 36V ka phepelo ea hajoale ea 1A. Netefatsa hore o sebelisa phepelo ea motlakase e tsamaellanang ea DC bakeng sa ts'ebetso e nepahetseng.
Nka holisa ts'ebetso ea Stam PLC joang?
O ka holisa ts'ebetso ka ho sebelisa lithapo tsa GPIO le lihokelo tse ling tse fanoeng. Hokela li-sensor le li-actuator ho li-interfaces tsa Grove bakeng sa bokhoni bo ntlafalitsoeng.
Litokomane / Lisebelisoa
 |
M5STACK StamPLC IoT Programmable Logic Controller [pdf] Bukana ea Mosebelisi StamPLC IoT Programmable Logic Controller, IoT Programmable Logic Controller, Programmable Logic Controller, Logic Controller |