Tsela ea Phallo ea M5STACK M5FGV4

Litlhaloso

• Boholo ba Mojule: 60.3 * 60.3 * 48.9mm

Tlhahisoleseding ya Sehlahiswa

The Flow Gateway ke sesebelisoa se feto-fetohang se nang le matla a fapaneng a puisano le li-sensor, tse etselitsoeng ho hokahana ka mokhoa o se nang moeli mererong ea hau. E na le skrine ea IPS ea 2.0-inch capacitive touch, li-interfaces tse ngata tsa puisano, li-sensor, le likhetho tsa taolo ea matla.

Bokhoni ba Puisano

• Molaoli ea ka Sehloohong: ESP32-S3FN8
• Puisano e Se nang Wireless: Ts'ebetso ea Wi-Fi, BLE, Infrared (IR).
• CAN Bus Interfaces: Likhokahano tse 'nè tse tšehetsang puisano ea lisebelisoa tse ngata

Lithakhisa tsa GPIO le li-interfaces tse ka khonehang

• Grove Ports: Port A: I2C Interface, Port B: UART Interface, Port C: ADC Interface
• Slot ea TF Card: Bakeng sa polokelo e atolositsoeng
• Sebopeho sa Onboard: Mofuta oa C bakeng sa ho etsa mananeo le puisano ea serial

Tsamaiso ea Matla

• Chip ea Taolo ea Matla: AXP2101 e nang le likanale tse 'ne tsa taolo ea phallo ea matla
• Phepelo ea motlakase: Ka ntle DC 12V (e tšehetsa 9~24V) kapa ka hare 500mAh lithium battery (M5Go2 Base)
• Moralo oa tšebeliso e tlase ea matla

Ts'ebetso ea Mohala

• Audio Decoder Chip: ES7210 e nang le kenyeletso ea li-microphone tse peli
• AmpLifier Chip: 16-bit I2S AW88298
• Sepikara se Ahelletsoeng ka hare: 1W sebui sa boleng bo holimo

Litšobotsi Tsa 'Mele

• Boemo ba 'Mele: 60.3 * 60.3 * 48.9mm
• Boima ba 'mele: 290.4g
• Likonopo: Konopo e ikemetseng ea matla le konopo ea reset (RST) e nang le potoloho ea ho lieha

Litaelo tsa Tšebeliso ea Sehlahisoa

Ho qala ka potlako - Skena Boitsebiso ba Wi-Fi

1. Bula Arduino IDE (Sheba ho Tataiso ea ho kenya Arduino IDE)
2. Tobetsa o hatelle konopo ea Seta Botjha, ebe o kenya thapo
3. Khetha boto ea M5CoreS3 le boema-kepe bo lumellanang, ebe u kenya khoutu
4. Bula sebali sa serial ho bonts'a WiFi e hlahlobiloeng le tlhahisoleseling ea matla a lets'oao

Qalo e Potlakileng - Skena Lintlha tsa Sesebelisoa sa BLE

1. 1. Bula Arduino IDE (Sheba ho Tataiso ea ho kenya Arduino IDE)

Ka kopo etsa bonnete ba hore u latela litaelo ka hloko bakeng sa ts'ebetso e atlehileng ea Phallo Gateway.

Lipotso Tse Botsoang Hangata

• P: Ke tjhaja betri ea ka hare ea lithium joang?
  • A: Ho tjhaja betri ea lithium e ka hare, hokela sesebelisoa mohloling oa motlakase o kantle oa DC o sebelisa thapo e fanoeng ea Type-C.
• P: A na nka eketsa bokhoni ba polokelo ea Flow Gateway?
  • A: E, o ka eketsa bokhoni ba polokelo ka ho kenya karete ea TF ka har'a slot ea karete ea TF e inehetseng mochine.
• P: Ke matla afe a khothalletsoang a ho sebetsatage bakeng sa Phallo Gateway?
  • A: The Flow Gateway e tšehetsa motlakase oa kantle oa DC oa 12V (range: 9 ~ 24V) kapa o ka tsamaisoa ke 500mAh lithium betri ea ka hare.

TLHOKOMELO

Flow Gateway ke mojule oa katoloso ea mesebetsi e mengata e thehiloeng ho moamoheli oa M5CoreS3, o kopanyang li-interfaces tsa libese tsa 4 CAN le limmapa tse ngata tsa GPIO, ho fana ka bokhoni bo matla ba ho atolosa bakeng sa taolo ea indasteri le lits'ebetso tsa IoT. Mojule ona o entsoe ka mokhoa o bonolo kelellong, o ts'ehetsa ho bokellana ka seamless ka lisebelisoa tsa letoto la M5Stack. E boetse e na le taolo ea matla e hahelletsoeng kahare le mesebetsi ea katoloso ea I2C, e e etsa hore e be e loketseng bakeng sa maemo a rarahaneng a hlokang puisano ea lisebelisoa tse ngata le taolo e nepahetseng.

Phallo Gateway

1. Matla a Puisano:
   • Molaoli ea ka Sehloohong: ESP32-S3FN8
   • Puisano e se nang mohala: Wi-Fi, BLE, Infrared (IR) ts'ebetso
   • Li-interfaces tse 'nè tsa CAN Bus: E tšehetsa puisano ea lisebelisoa tse ngata
2. processor le Tshebetso:
   • Mohlala oa processor: Xtensa LX7 (ESP32-S3FN8)
   • Bokhoni ba polokelo: 16MB Flash, 8MB PSRAM
   • Maqhubu a Ts'ebetso: Xtensa® dual-core 32-bit LX7 microprocessor, ho fihla ho 240 MHz
3. Pontšo le Kenyo:
   • Skrine: Skrine sa 2.0-inch capacitive touch IPS se nang le khalase e matla haholo
   • Touch Sensor: GT911 bakeng sa taolo e nepahetseng ea ho ama
   • Khamera: 0.3-megapixel GC0308
   • Sensor ea haufi: LTR-553ALS-WA
4. Sensora:
   • Accelerometer le Gyroscope: BMI270
   • Magnetometer: BMM150
   • Nako ea Sebele (RTC): BM8563EMA
5. Lithako tsa GPIO le li-interfaces tse ka khonehang:
   • Grove Ports:
   • Boema-kepe A: I2C Interface
   • Port B: UART Interface
   • Port C: ADC Interface
   • TF Card Slot: Bakeng sa polokelo e atolositsoeng
   • Onboard Interface: Type-C bakeng sa ho etsa mananeo le puisano ea serial
6. Taolo ea Matla:
   • Power Management Chip: AXP2101 e nang le litsela tse 'nè tsa ho laola matla a matla
   • Phepelo ea Matla: Ka ntle DC 12V (e tšehetsa 9 ~ 24V) kapa ka hare 500mAh lithium battery (M5Go2 Base)
   • Moralo oa tšebeliso e tlase ea matla
7. Ho sebetsa ha molumo:
   • Audio Decoder Chip: ES7210 e nang le kenyeletso ea li-microphone tse peli
   • AmpLifier Chip: 16-bit I2S AW88298
   • Sebui se Ahetsoeng: Sebui sa 1W se tšepahalang haholo
8. Litšobotsi tsa 'Mele:
   • Boima ba 'mele: 60.3 * 60.3 * 48.9mm
   • Boima ba 'mele: 290.4g
   • Likonopo: Konopo ea matla e ikemetseng le konopo ea reset (RST) e nang le potoloho ea ho lieha

Tlhaloso

Boholo ba Mojule

PHAKAMATSO

Pele o etsa mohato ona, sheba sengoloa sehlomathisong sa ho qetela: Ho kenya Arduino

Hatisa lintlha tsa WiFi

1. Bula Arduino IDE (Sheba ho https://docs.m5stack.com/en/arduino/arduino_ide bakeng sa tataiso ea ho kenya bakeng sa boto ea nts'etsopele le software)
2. Tobetsa o hatelle konopo ea Seta Botjha, ebe o kenya thapo
3. Khetha boto ea M5CoreS3 le boema-kepe bo lumellanang, ebe u kenya khoutu
4. Bula sebali sa serial ho bonts'a WiFi e hlahlobiloeng le tlhahisoleseling ea matla a lets'oao

PHAKAMATSO

Pele o etsa mohato ona, sheba sengoloa sehlomathisong sa ho qetela: Ho kenya Arduino

Hatisa lintlha tsa BLE

1. Bula Arduino IDE (Sheba ho https://docs.m5stack.com/en/arduino/arduino_ide bakeng sa tataiso ea ho kenya bakeng sa boto ea nts'etsopele le software)
2. Tobetsa o hatelle konopo ea Seta Botjha, ebe o kenya thapo
3. Khetha boto ea M5CoreS3 le boema-kepe bo lumellanang, ebe u kenya khoutu
4. Bula sebali sa serial ho bonts'a BLE e hlahlobiloeng le tlhaiso-leseling ea matla

Phatlalatso ea FCC

Tlhokomeliso ea FCC

Tlhokomeliso ea FCC:

Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.

Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

1. Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi, le
2. sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.

TLHOKOMELISO EA BOHLOKOA:

Tlhokomeliso: Thepa ena e lekoa 'me e fumanoe e lumellana le meeli ea Sesebediswa sa Dijithale sa Sehlopha sa B, ho latela karolo ya 15 ya Melao ya FCC. Meeli ena e etselitsoe ho fana ka tšireletso e utloahalang khahlanong le tšitiso e kotsi mohahong oa bolulo.

Thepa ena e hlahisa, e sebelisa le ho khantša matla a maqhubu a seea-le-moea, 'me haeba e sa kengoa le ho sebelisoa ho latela litaelo, e ka baka tšitiso e kotsi likhokahanong tsa radio. Leha ho le joalo, ha ho na tiiso ea hore tšitiso e ke ke ea etsahala setsing se itseng. Haeba sesebelisoa sena se baka tšitiso e kotsi ea seea-le-moea kapa kamohelo ea thelevishene, e ka lekanyetsoang ka ho tima le ho tima sesebelisoa, mosebelisi o khothalletsoa ho leka ho lokisa tšitiso ka e le 'ngoe kapa tse ling tsa mehato e latelang:

• Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
• Eketsa karohano pakeng tsa thepa le moamoheli.
• Hokela lisebelisoa le seketsoaneng sa potoloho se fapaneng le seo moamoheli a hokahaneng le sona.
• Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.

Polelo ea Ts'oaetso ea Mahlaseli a FCC:

Sesebelisoa sena se latela meeli ea ho pepeseha ha radiation ea FCC e behetsoeng tikoloho e sa laoleheng. Sesebelisoa sena se lokela ho kengoa le ho sebetsoa ka sebaka se tlase sa 20cm lipakeng tsa radiator le 'mele oa hau

Ho kenya Arduino

• Ho kenya Arduino IDE (https://www.arduino.cc/en/Main/Software) Tobetsa ho etela ofisiri ea Arduino website, 'me u khethe sephutheloana sa ho instola hore sistimi ea hau ea ts'ebetso e jarolloe.
• 二. Ho kenya Tsamaiso ea Boto ea Arduino

1. Motsamaisi oa Boto URL e sebelisoa ho supa lintlha tsa boto ea nts'etsopele bakeng sa sethala se itseng. Ho menu ea Arduino IDE, khetha File -> Likhetho
2. Kopitsa tsamaiso ea boto ea ESP URL ka tlase ho Motsamaisi oa Boto ea Tlatsetso URLs: lebala, 'me u boloke.
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Ka lehlakoreng le leng, khetha Mookameli oa Boto, batla ESP, ebe o tobetsa Kenya
4. Ka lehlakoreng le leng, khetha Mookameli oa Boto, batla M5Stack, ebe o tobetsa Kenya. Ho latela sehlahisoa se sebelisitsoeng, khetha boto ea nts'etsopele e tsamaellanang tlasa Lisebelisoa -> Boto -> M5Stack -> {M5CoreS3}
5. Hokela sesebediswa khomphuteng ya hao ka thapo ya data ho kenya lenaneo

Litokomane / Lisebelisoa

Tsela ea Phallo ea M5STACK M5FGV4 [pdf] Bukana ea Mosebelisi M5FGV4, M5FGV4 Phallo Gateway, Phallo Gateway, Gateway

Litšupiso

• Bukana ea Mosebelisi