INNO Instrument 3X Active V Groove Cladding Alignment Fusion Splicer

Tlhahisoleseding ya Sehlahiswa

Litlhaloso

• Mohlala: Active V-Groove Cladding Alignment Fusion Splicer
• Mofuta: Lethathamo la V2.00
• Phepelo ea motlakase: E sebetsoa ke betri
• Likaroloana: Mokhoa oa ho kopanya o sebetsang, Mokhoa oa ho futhumatsa, menu ea tlhokomelo

Litaelo tsa Tšebeliso ea Sehlahisoa

Tlhokomeliso ea Tšireletseho le Litlhokomelo

• Netefatsa hore o bala litemoso tsohle tsa polokeho le litemoso bukeng ea mosebelisi pele o sebelisa fusion splicer.

Litlhokomelo tsa Battery

• Latela litataiso tse fanoeng bakeng sa ho sebetsana le ho tjhaja betri ea splicer ho netefatsa ts'ebetso e nepahetseng.

Ho kenya

• Hlophisa splicer ea fusion sebakeng se tsitsitseng se nang le sebaka se lekaneng bakeng sa ts'ebetso le moea o nepahetseng.

Fetileview ea Likarolo tse Ntle

• Itloaetse ka likarolo tsa kantle tsa fusion splicer joalo ka ha ho hlalositsoe bukeng ea mosebelisi ho utloisisa ts'ebetso ea eona.

Mokhoa oa ho Fana ka Matla

• Sebelisa mokhoa o boletsoeng oa phepelo ea motlakase joalo ka ha ho bonts'itsoe bukeng ea ho matlafatsa fusion splicer.

Ts'ebetso ea Motheo

Ho bulela Splicer

• Latela mehato e hlalositsoeng bukeng ea ho kenya letsoho ka mokhoa o sireletsehileng ho fusion splicer.

Ho lokisa Fiber

• Hloekisa le ho lokisa fiber bakeng sa ho kopanya ho latela litaelo tse fanoeng bukeng ea mosebelisi.

Mokhoa oa ho etsa Splice

• Sheba mokhoa o qaqileng oa bukana oa ho etsa lesela le sebelisa fusion splicer.

Mokhoa oa ho Sireletsa Splice

• Ithute mokhoa oa ho sireletsa splice ka mor'a ho qeta ka ho latela litataiso bukeng ea mosebedisi.

Lipotso Tse Botsoang Hangata

P: Ke hloekisa splicer ea fusion joang kamora ho e sebelisa?

A: Ho hloekisa splicer ea fusion, sebelisa lesela le bonolo, le omeletseng ho hlakola lerōle kapa litšila. Qoba ho sebelisa lisebelisoa tse hloekisang metsi ka kotloloho sesebelisoa.

P: A na nka kopanya mefuta e fapaneng ea likhoele ka splicer ee ea fusion?

A: The fusion splicer e etselitsoe ho kopanya mefuta e itseng ea likhoele. Sheba bukana ea mosebelisi kapa ikopanye le ts'ehetso ea bareki bakeng sa tlhaiso-leseling e amanang le eona.

Selelekela

• Kea leboha ha u khethile View 3X Fusion Splicer ho tsoa ho INNO Instrument. The View 3X ke Active V-Groove Cladding Alignment Fusion Splicer e nang le likarolo tse tsamaisoang ke AI le li-Module tsa IoT le GPS tse kentsoeng. Hape le sena, theknoloji e ncha ka ho feletseng e fokotsa haholo nako ea ho kopanya le ho futhumatsa. Mokhoa o tsoetseng pele oa likhakanyo le mokhoa oa ho hokahanya o netefatsa khakanyo e nepahetseng ea tahlehelo ea splice. Sebopeho se matla sa ts'ebetso le mokhoa o ikemetseng oa splice o fa basebelisi boiketlo bo boholo.
• Bakeng sa boitsebiso bo eketsehileng ba View 3X, ka kopo etela ofisiri ea rona website at www.innoinstrument.com.
• Bukana ena ea mosebelisi e hlalosa ts'ebeliso, litšobotsi tsa ts'ebetso, le litemoso tsa View 3X fusion splicer le mokhoa oa ho e kenya le ho e sebelisa.
• Sepheo se seholo sa bukana ena ke ho etsa hore mosebedisi a tloaelane le splicer ka hohle kamoo ho ka khonehang.
• Bohlokoa! INNO Instrument e khothaletsa basebelisi bohle ho bala bukana ena pele ba e sebelisa View 3X fusion splicer.

Ho kenya

Tlhokomeliso ea Tšireletseho le Litlhokomelo

• As View 3X e etselitsoe fusion splicing silica glass optical fibers, ho bohlokoa haholo hore splicer e se ke ea sebelisoa bakeng sa merero efe kapa efe. The splicer ke sesebelisoa se nepahetseng 'me se tlameha ho sebetsoa ka hloko.
• Ka hona, o lokela ho bala melao e latelang ea polokeho le litemoso tse akaretsang bukeng ena. Ketso life kapa life tse sa lateleng litemoso le litemoso li tla tlola maemo a polokeho a moralo, tlhahiso, le ts'ebeliso ea fusion splicer.
• INNO Instrument e ke ke ea nka boikarabelo leha e le bofe bakeng sa liphello tse bakoang ke tšebeliso e mpe.

Litemoso tsa Tšireletso ea Ts'ebetso

• Le ka mohla u se ke ua sebelisa splicer sebakeng se tukang mollo kapa se phatlohang.
• O SE KE oa ama li-electrode ha splicer e butsoitse.
• Hlokomela: Sebelisa li-electrode tse boletsoeng feela bakeng sa fusion splicer. Kgetha [Fetola eleketrode] ho Menu ya Tlhokomelo ho nkela dielectrode sebaka, kapa tima splicer, hakolla mohloli wa matla a AC, le ho ntsha betri pele o kenya dielectrode.
• U se ke ua qala ho ntša arc ntle le haeba li-electrode ka bobeli li le sebakeng se nepahetseng.
• Se ke oa arola kapa oa fetola likarolo life kapa life tsa splicer ntle le tumello, ntle le likarolo kapa likarolo tse lumelletsoeng ka ho hlaka bakeng sa ho qhaqhoa kapa ho fetoloa ke basebelisi joalo ka ha ho hlalositsoe bukeng ena. Phetoho ea likarolo le litokiso tsa kahare li lokela ho etsoa feela ke INNO kapa litsebi tsa eona tse lumelletsoeng kapa lienjineri.
• Qoba ho sebelisa splicer libakeng tse nang le maro a ka tukang kapa mouoane, kaha lehare la motlakase le hlahisoang ke splicer le ka baka kotsi ea mollo o kotsi kapa ho phatloha. Qoba ho sebelisa splicer haufi le mehloli ea mocheso, libakeng tse phahameng tsa mocheso le lerōle, kapa ha condensation e le teng holim'a splicer, kaha sena se ka lebisa ho ts'oenyeho ea motlakase, ho se sebetse ha splicer, kapa ho senyeha ha ts'ebetso ea splicing.
• Ho bohlokoa ho roala likhalase tsa polokeho nakong ea ho lokisa fiber le ts'ebetso ea ho kopanya. Likaroloana tsa fiber li ka baka kotsi e kholo haeba li ka kopana le mahlo, kapa letlalo, kapa ha li ka nooa.
• Tlosa betri hang-hang haeba e 'ngoe ea lintlha tse latelang e hlokomeloa ha u ntse u sebelisa splicer:
• Mosi, menko e sa thabiseng, lerata le sa tloaelehang, kapa mocheso o feteletseng.
• Mokelikeli kapa lintho tse tsoang linaheng tse ling li kena 'meleng oa splicer (casing).
• The splicer e senyehile kapa e oa.
• Haeba ho na le e 'ngoe ea liphoso tsena, ka kopo ikopanye le setsi sa rona sa litšebeletso hang-hang. Ho lumella splicer hore e lule e senyehile ntle le ho nka khato hang-hang ho ka lebisa ho hloleheng ha lisebelisoa, ts'ebetso ea motlakase le mollo, 'me ho ka baka kotsi kapa lefu.
• Qoba ho sebelisa khase e hatelitsoeng kapa moea o ka makotikoting bakeng sa ho hloekisa splicer, kaha lihlahisoa tsena li ka ba le lisebelisoa tse tukang tse ka hotetsang nakong ea ho tsoa ha motlakase.
• Sebelisa feela betri e tloaelehileng e behiloeng bakeng sa View 3X. Tšebeliso ea mohloli o fosahetseng oa matla a AC e ka baka mosi, ho tsukutloa ke motlakase, le tšenyo ea lisebelisoa, 'me ho ka baka mollo, kotsi kapa lefu.
• Sebelisa feela tjhaja e boletsoeng bakeng sa View 3X. Qoba ho beha lintho tse boima holim'a thapo ea motlakase ea AC 'me u netefatse hore e lula hole le mehloli ea mocheso.
• Tšebeliso ea thapo e sa nepahalang kapa e senyehileng e ka baka mosi, ho tsukutloa ke motlakase le tšenyo ea thepa, 'me ho ka baka mollo, kotsi kapa lefu.

Tlhokomelo le Tlhokomelo ea Kantle ea Tlhokomelo

• Qoba ho sebelisa lintho tse thata ho hloekisa V-grooves le li-electrode.
• Qoba tšebeliso ea acetone, thinner, benzol, kapa joala ho hloekisa karolo efe kapa efe ea splicer, ntle le libakeng tse khothaletsoang.
• Sebelisa lesela le omeletseng ho felisa lerōle le litšila ho tloha splicer.
• Kamehla latela litaelo tsa tlhokomelo bukeng ena.

Litlhokomelo tsa Lipalangoang le Polokelo

• Ha o tsamaisa kapa o tsamaisa splicer ho tloha serameng ho ea sebakeng se futhumetseng, ho bohlokoa ho lumella fusion splicer hore e futhumale butle-butle ho thibela condensation ka hare ho yuniti, e ka bang le liphello tse kotsi ho splicer.
• Tšoaea splicer ea fusion hantle bakeng sa polokelo ea nako e telele.
• Boloka splicer e hloekile ebile e omme.
• Ka lebaka la liphetoho tsa eona tse nepahetseng le ho tsamaisana, boloka splicer ka mokotlaneng oa eona oa ho jara ka linako tsohle ho e sireletsa tšenyo le litšila.
• Kamehla qoba ho siea splicer letsatsing le tobileng kapa ho pepesehela mocheso o feteletseng.
• U se ke ua boloka splicer sebakeng se lerōle. Sena se ka baka ts'abo ea motlakase, ho se sebetse hantle ha splicer, kapa ts'ebetso e mpe ea ho kopanya.
• Boloka mongobo boemong bo fokolang moo splicer e bolokiloeng teng. Mongobo ha oa lokela ho feta 95%.

Litlhokomelo tsa betri

• Qoba ho thetsa kapa ho otla betri ka lintho tse nchocho kapa tse bohale.
• Boloka betri hole le lisebelisoa tsa tšepe le lintho.
• Qoba ho lahlela, ho liha, ho sitisa, kapa ho koba betri, 'me u qobe ho e kokota kapa ho e hatakela.
• Se ke oa hokela li-anode le li-cathode tsa betri ka litšepe tse kang terata ea motlakase ho thibela li-circuits tse ka bang teng.
• Netefatsa hore anode kapa cathode terminal ea betri ha e kopane le lera la aluminium ea sephutheloana, kaha e ka baka sekhechana se khuts'oane.
• Se ke oa harola sele ea betri.
• Qoba ho qoelisa betri ka metsing, kaha tšenyo ea metsi e tla etsa hore sele ea betri e se ke ea sebetsa.
• Se ke oa beha kapa oa sebelisa betri haufi le mehloli ea mocheso, joalo ka mollo, 'me u thibele betri hore e se chese ho feta tekano.
• Qoba ho kopanya betri ka kotloloho 'me u qobe ho e tjhaja libakeng tse chesang haholo.
• Se ke oa beha betri ka ontong ea microwave kapa sejaneng sefe kapa sefe sa khatello e phahameng.
• Tlosa betri hole le libaka tse chesang, joalo ka ka koloing nako e telele kapa mahlaseling a letsatsi.
• Ho thibetsoe ka thata ho sebelisa betri e senyehileng.
• Haeba electrolyte e lutla, boloka betri hole le mohloli ofe kapa ofe oa mollo.
• Haeba betri e ntša monko oa electrolyte, u se ke oa e sebelisa.

Ho kenya

• Bohlokoa! Latela litaelo tsena ka hloko.
• Ho manolla Splicer Tšoara mohele holimo, ebe o phahamisa splicer ka ntle ho mokotlana o jereng.

Fetileview ea Likarolo tse Ntle

Mokhoa oa ho fana ka matla Battery

Setšoantšo se latelang se bontša mokhoa oa ho kenya betri.

1. Tima Fusion Splicer Tobetsa konopo ea tokollo, sena se tla u lumella ho theola betri ho tsoa ho Fusion Splicer.
2. Sututsa betri
3. Beha betri ka har'a sekotjana sa yuniti ea matla
   • E sutumelletse sebakeng se nepahetseng.

Ts'ebetso ea Motheo

Ho bulela Splicer

• Tobetsa konopo e holim'a phanele ea ts'ebetso, ebe u emela hore splicer e bule. Ebe u ea leqepheng la Workbench.
• Hlokomela: LCD Monitor ke karolo e nepahetseng e hlahisoang ke feme ea rona ea tlhahiso tlasa taolo e thata ea boleng. Leha ho le joalo, matheba a mang a manyenyane ka mebala e fapaneng a ntse a ka sala skrineng.
• Ho sa le joalo, khanya ea skrine e kanna ea se ke ea bonahala e ts'oana, ho ipapisitse le viewing angle. Hlokomela hore matšoao ana ha se liphoso, empa ke liketsahalo tsa tlhaho.

Ho lokisa Fiber

Mehato ena e 3 e lokela ho etsoa pele ho splicing.

1. Ho hlobola: Tlosa bonyane limilimithara tse 50 tsa sekoaelo sa bobeli (se sebetsang bakeng sa seaparo sa bobeli se thata le se hlephileng) le hoo e ka bang 30 ~ 40mm ea seaparo sa mantlha se nang le stripper e loketseng.
2. Hloekisa likhoele tse se nang letho e nang le lesela le kolobisitsoeng ka joala kapa lesela le se nang letlapa.
3. Tlosa fiber: E le ho etsa bonnete ba hore ho na le sephetho se setle ka ho fetisisa sa splicing, qhaqha likhoele ka sekhahla se phahameng se nepahetseng se kang INNO Instrument V series fiber cleaver, 'me u laole ka thata bolelele ba ho phunya bo bontšitsoeng ka tlase.

• Hlokomela: Ka linako tsohle u hopole ho sunya letsoho le honyehang mocheso pheletsong efe kapa efe ea likhoele qalong ea tokiso e 'ngoe le e 'ngoe ea fiber.
• Bohlokoa! Etsa bonnete ba hore fiber e se nang letho le karolo ea eona e petsohileng li hloekile.
• Qoba ho beha likhoele fatše sebakeng se sebetsang se lerōle.
• Qoba ho tsoka likhoele ho potoloha moeeng.
• Sheba hore na V-grooves e hloekile; haeba ho se joalo, li hlakole ka k'hothone e hloekileng e kolobisitsoeng ka joala.
• Sheba hore na clamps ba hloekile; haeba ho se joalo, li hlakole ka k'hothone e hloekileng e kolobisitsoeng ka joala.

Mokhoa oa ho etsa Splice

• Bula sekoahelo se thibelang moea.
• Bula fiber clamps.
• Beha likhoele ka har'a V-grooves. Etsa bonnete ba hore likarolo tsa fiber li pakeng tsa V-groove le ntlha ea electrode.
• Clamp faeba e boemong ka ho koala lihlopha tse peli tsa fiber clamps.
• Koala sekoahelo se thibelang moea.
• Hlokomela: Etsa bonnete ba hore u qoba ho thellisa likhoele haufi le V-grooves, empa ho e-na le hoo u li behe holim'a V-grooves 'me u li sekamise fatše (joalokaha ho bontšitsoe ka tlase).

Ho hlahloba li-Fibers

• Pele o tsoela pele ka ho kopanya, hlahloba likhoele ho bona hore na li hloekile ebile li petsohile hantle. Haeba ho na le mefokolo, ka kopo tlosa likhoele 'me u li lokise hape.
• Lipheletso tsa fiber li bonahala ho sebali.
• Fiber e fella ka ntle ho leihlo.
• Fiber e fella ka holimo le ka tlase ho sebali - ha e bonahale.
• Hlokomela: Likhoele li hlahlojoa ka bo eona ha u tobetsa konopo ea Seta. The splicer e shebana le likhoele ka bo eona ebe e hlahloba tšenyo kapa likaroloana tsa lerole.

Ho kopanya

• Khetha mokhoa o nepahetseng oa ho kopanya.
• Qala ho kopanya ka ho tobetsa konopo ea "SET".
• Hlokomela: Haeba splicer e behiloe ho "Auto Start", splicing e tla qala ka bo eona hang ha sekoahelo sa moea se thibela moea se koetsoe.

Mokhoa oa ho Sireletsa Splice

• Ka mor'a ho kopanya, kenya fiber e nang le letsoho le fokotsa mocheso ka har'a heater. Tobetsa konopo ea [Heat] ho qala ho futhumatsa.

Mokhoa oa ho futhumatsa

• Bula sekwahelo sa heater
• Bula li-fiber holders tse ka ho le letšehali le tse nepahetseng. Tšoara letsoho le fokotsa mocheso (le neng le behiloe holim'a fiber). Phahamisa likhoele tse kopantsoeng 'me u li tšoare ka thata. Ebe u thellela letsoho la ho honyetsa mocheso sebakeng sa splice.
• Beha fiber e nang le letsoho le fokotsa mocheso ka har'a heater clamp.
• Tobetsa konopo ea [SET] ho qala ho futhumatsa. Ha ho phetheloa, letšoao la ho futhumatsa la LED le tla tima.

Mokhoa oa Splice

• View 3X e na le mefuta e fapaneng ea mekhoa e bonolo empa e matla haholo ea splice e hlalosang maqhubu a arc, linako tsa splice hammoho le li-parameter tse fapaneng tse sebelisoang ha ho etsoa splice. Ho bohlokoa ho khetha mokhoa o nepahetseng oa splice.
• Ho na le mekhoa e mengata ea "Preset" bakeng sa motsoako o tloaelehileng oa fiber. Ka hona, ho bonolo haholo ho fetola le ho ntlafatsa liparamente bakeng sa motsoako o sa tloaelehang oa fiber.

Ho hlahisa Mokhoa o Hlahang oa Splice

• Mokhoa o sebetsang oa splice o lula o bontšoa ka lehlakoreng le letšehali la skrine (sheba ka tlase).

Ho khetha mokhoa oa Splice

• Khetha [Splice mode] ho tsoa ho Main Menu.
• Khetha mokhoa o nepahetseng oa ho kopanya
• Mokhoa o khethiloeng oa ho arohana o hlaha skrineng.
• Tobetsa konopo ea [Reset] ho khutlela leqepheng la pele la sebopeho.

Kakaretso Splicing Mehato

• Karolo ena e hlalosa mehato e amehang ts'ebetsong ea othomathike ea ho kopanya le ho hlalosa hore na li-parameter tse fapaneng tsa splice mode li amana joang le ts'ebetso ena.
• Mokhoa o tloaelehileng oa ho kopanya o ka aroloa likarolo tse peli: pele ho fusion le fusion.

Pele ho Fusion

• Nakong ea pele ho fusion, splicer e etsa ho tsamaisana ka mokhoa o itekanetseng le ho tsepamisa maikutlo, moo likhoele li tlas'a mocheso o tlase pele ho fusion bakeng sa merero ea ho hloekisa; setšoantšo sa pele ho fusion le sona se nkuoa.
• Mothating ona, mosebelisi o tsebisoa ka mathata afe kapa afe a bonoang setšoantšong sa pele ho fusion, joalo ka likhoele tse sa lokisoang hantle. Joale splicer e tla hlahisa temoso pele likhoele li kopantsoe hammoho.

Fusion

• Nakong ea fusion, likhoele li kopantsoe hammoho 'me li tsamaisoa ke maqhubu a mahlano a fapaneng joalokaha ho bontšitsoe ka tlase.
• Parameter ea bohlokoa, e fetohang nakong ea splicing, ke sebaka se pakeng tsa likhoele. Nakong ea pele ho fusion, likhoele li arohane. Ha karolo ea hona joale e fetoha, likhoele li arotsoe butle-butle.

Mokhoa oa Splicing

• Matla a arc le nako ea arc li nkoa e le li-parameter tse peli tsa bohlokoa ka ho fetisisa (joalokaha ho bontšitsoe setšoantšong se ka tlase).
• Lebitso le sepheo sa liparamente tseo, hammoho le phello le bohlokoa ba litekanyetso, li tla hlalosoa karolong e latelang ea 'Standard Splicing Parameters'.
• Setšoantšo se ka tlase se bontša maemo a ho ntša arc (kamano pakeng tsa "matla a Arc" le "Motor motion").
• Maemo ana a ka fetoloa ka ho fetola li-parameter tsa splicing tse thathamisitsoeng ka tlase. Leha ho le joalo, ho itšetlehile ka mokhoa oa splice, li-parameter tse itseng li ke ke tsa fetoloa.
• A: Matla a pele ho fuse
• B: Arc 1 matla
• C: Arc 2 Matla
• D: Ho hloekisa Arc
• E: Nako ea pele ho fuse
• F: Nako ea Pele e amanang le Overlap G: Arc 1 nako
• H: Arc 2 KA nako
• I: Arc 2 OFF nako
• J: Arc 2 nako
• K: Taper Splicing Ema Nako
• L: Taper Splicing Nako
• M: Taper Splicing lebelo
• N: Re-arc Nako
• Setšoantšo sa boemo ba ho tsoa ha ARC

Mekhahlelo e Tloaelehileng ea Splicing

Paramethara	Tlhaloso
Setšoantšo	Lenane la mefuta ea li-splice tse bolokiloeng sebakeng sa polokelo ea li-splicer lia hlaha. Ha u khetha mokhoa o nepahetseng, litlhophiso tse khethiloeng tsa splice mode li kopitsoa ho mokhoa o khethiloeng oa splice sebakeng se ka sebelisoang ke mosebedisi.
Lebitso	Sehlooho sa mokhoa oa splice (ho fihla ho litlhaku tse supileng)
Hlokomela	Tlhaloso e qaqileng ea mokhoa oa splice (ho fihla ho litlhaku tse 15). E hlahisoa ho "Khetha mokhoa oa ho kopanya" menu.
Hlophisa Mofuta	Beha mofuta oa alignment bakeng sa likhoele. "Core": ho tsamaisana ha fiber core
Arc fetola	Fetola matla a arc ho latela maemo a likhoele.
Hula teko	Haeba "Pull test" e behiloe "ON", teko ea ho hula e etsoa ha ho buloa sekoahelo sa moea kapa ka ho tobetsa konopo ea SET ka mor'a ho kopanya.
Khakanyo ea tahlehelo	Khakanyo ea tahlehelo e lokela ho nkoa e le tšupiso. Kaha tahlehelo e baloa ho latela setšoantšo sa fiber, e ka 'na ea fapana le boleng ba sebele. Mokhoa oa khakanyo o ipapisitse le fiber ea mofuta o le mong mme o baloa ka bolelele ba 1.31μm. Theko e lekantsoeng e ka ba tšupiso ea bohlokoa, empa e ke ke ea sebelisoa e le motheo oa kamohelo.
Bonyane tahlehelo	Chelete ena e eketsoa ho tahlehelo e hakanyetsoang ea splice e neng e balletsoe qalong. Ha u kopanya likhoele tse khethehileng kapa tse sa tšoaneng, tahlehelo e phahameng ea splice e ka etsahala esita le ka maemo a optimized arc. Ho etsa hore tahlehelo e hakantsoeng ea splice e ts'oane le tahlehelo ea 'nete ea splice, beha tahlehelo e nyane ho boleng ba phapang.
Tahlehelo Moedi	Molaetsa oa phoso o hlahisoa haeba tahlehelo e hakantsoeng e feta moeli oa tahlehelo o behiloeng.
Core angle limit	Molaetsa oa phoso o bonts'oa haeba angle e kobehang ea likhoele tse peli tse arohaneng e feta moeli o khethiloeng (Core angle limit).
Hlakola moeli oa angle	Molaetsa oa phoso o hlahisoa haeba angle ea cleave ea fiber e ka ho le letšehali kapa e ka ho le letona e feta moeli o khethiloeng (moeli oa ho koala).
Boemo ba lekhalo	E beha boemo bo lekanyelitsoeng ba sebaka sa ho kopanya ho ea bohareng ba li-electrode. Tahlehelo ea li-splice e ka ntlafatsoa tabeng ea ho arohana ha fiber e sa tšoaneng ka ho suthela [Gap position] ho leba fiber eo MFD e leng kholo ho feta fiber e 'ngoe ea MFD.
Lekhalo	Beha lekhalo la sefahleho sa ho qetela pakeng tsa likhoele tse ka ho le letšehali le tse ka ho le letona nakong ea ho lokisoa le ho tsoa pele ho fusion.
Kopana	Beha palo e fetelletseng ea likhoele ho fiber propelling stage. E batla e le nyane [Overlap] e kgothaletswa haeba [Preheat Arc Value] e le tlase, ha e batla e le kgolo [Overlap] e kgothaletswa haeba [Preheat Arc Value] e phahame.
Ho hloekisa nako ea Arc	Arc e hloekisang e chesa lerole le lenyane holim'a fiber ka ho tsoa ha arc nako e khuts'oane. Nako ea ho hloekisa arc e ka fetoloa ke parameter ena.
Preheat Arc boleng	Beha matla a pre-fuse arc ho tloha qalong ea ho tsoa ha arc ho ea qalong ea li-fibers propelling. Haeba "Preheat Arc Value" e behiloe tlase haholo, axial offset e ka etsahala haeba li-angles tse arohaneng li fokola. Haeba "Preheat Arc Value" e behiloe holimo haholo, lifahleho tsa fiber li kopanngoa haholo 'me tahlehelo ea splice ea eketseha.
Preheat Arc nako	Beha nako ea pre-fuse arc ho tloha qalong ea ho tsoa ha arc ho ea qalong ea likhoele tse tsamaisang likhoele. Nako e telele [Preheat Arc Time] le e phahameng [Preheat Arc Value] e lebisa liphellong tse tšoanang.
Boleng ba Fuse Arc	E beha matla a Arc.
Fuse Arc nako	E beha nako ea Arc.

Khetho ea Splice

Splice Mode Setting

1. Khetha [Khetho ea ho arola] ho Menu ea Mokhoa oa Splice.
2. Khetha parameter ho fetola.

Paramethara	Tlhaloso
Auto qala	Haeba "Autostart" e setetswe ho ON, ho kopanya ho iqalla hang feela ha sekwahelo se thibelang moya se kwalwa. Li-fiber li lokela ho lokisoa le ho kenngoa ka har'a splicer esale pele.
Emisa 1	Haeba “Pause 1” e setetswe ho ON, tshebetso ya ho kopanya e emisa ha difaeba di kena sebakeng se setehileng lekhalo. Li-angles tsa cleave li bontšoa nakong ea khefu.
Emisa 2	Haeba "Pause 2" e setetsoe ho ON, ts'ebetso ea ho kopanya e emisa ka mor'a hore mokhoa oa ho tsamaisana le fiber o phetheloe.
Hlokomoloha phoso ea splice
Hlakola angle	Ho beha "OFF" ho hlokomoloha liphoso 'me ho tsoela pele ho tlatsa splicing le haeba phoso e thathamisitsoeng e hlaha.
Konokono angle
Tahlehelo
Mafura
O mosesane
Setšoantšo sa fiber skrineng
Emisa 1	E beha mokhoa oa ho bonts'a litšoantšo tsa fiber skrineng ka nako e fapaneng ea stagts'ebetso ea ho kopanya.
Tsepanya
Emisa 2
Arc
Hakanya
Lekhalo le behiloeng

Mokhoa oa ho futhumatsa

• The splicer e fana ka mefuta e mengata ea mocheso oa 32, ho kenyelletsa le mekhoa ea mocheso ea 7 e behiloeng esale pele ke INNO Instrument, e ka fetoloang, ea kopitsoa le ho tlosoa ke mosebedisi.
• Khetha mokhoa oa ho futhumatsa o lumellanang hantle le letsoho la tšireletso le sebelisitsoeng.
• Bakeng sa mofuta o mong le o mong oa sleeve ea tšireletso, splicer e na le mokhoa o nepahetseng oa ho futhumatsa. Mefuta ena e ka fumanoa ka har'a sebopeho sa heater mode bakeng sa litšupiso.
• U ka kopitsa mokhoa o nepahetseng ebe u o beha ka mokhoa o mocha oa tloaelo. Basebelisi ba ka hlophisa liparamente tseo.

Ho khetha mokhoa oa ho futhumatsa

• Kgetha [Kgetha Mokgwa wa Mocheso] ho menu ya [Mokgwa wa Heater].

Editing Heat Mode

• Mekhahlelo ea ho futhumatsa ea mokhoa oa ho futhumatsa e ka fetoloa ke mosebedisi.

Hlakola Mokhoa oa Mocheso

• Hlokomela: Mefuta e grey-out (20mm, 30mm, 40mm, 50mm, 33mm) ke litlhophiso tsa sistimi tse ke keng tsa hlakoloa.

Liparamente tsa Mocheso oa Mocheso

Paramethara	Tlhaloso
Setšoantšo	E beha mofuta oa sleeve. Lenane la mefuta eohle ea mocheso le tla hlahisoa. Mokhoa o khethiloeng o tla kopitsoa ho mokhoa o mocha
Lebitso	Sehlooho sa mokhoa oa mocheso.
Mocheso oa heater	E beha mocheso oa mocheso.
Nako ea heater	E beha nako ea ho futhumatsa.
Mocheso oa preheat	Beha mocheso oa preheat.

Menu ea Tlhokomelo

• Splicer e na le mesebetsi e mengata ea ho etsa tlhokomelo e tloaelehileng.
• Karolo ena e hlalosa mokhoa oa ho sebelisa menu ea tlhokomelo. Khetha [Menu ea Tlhokomelo].
• Khetha mosebetsi oo o batlang ho o etsa.

Tlhokomelo

The splicer e na le ts'ebetso ea tlhahlobo ea tlhahlobo e hahelletsoeng e lumellang mosebelisi ho lekola likarolo tse 'maloa tsa bohlokoa tse feto-fetohang ka mohato o le mong feela o bonolo. Etsa mosebetsi ona haeba ho na le mathata a ts'ebetso ea splicer.

Mokhoa oa ts'ebetso

Che.	Hlahloba Ntho	Tlhaloso
1	Khatello ea LED	Lekanya le ho lokisa khanya ea LED.
2	Lerole Hlahloba	Lekola setšoantšo sa khamera bakeng sa lerōle kapa litšila 'me u hlahlobe hore na li sitisa tlhahlobo ea fiber. Haeba tšilafalo e bonoa, tobetsa konopo ea ho khutlisa habeli ho hlahisa sebaka sa eona.
3	Fetola Boemo	Phetoho ea fiber e ikemetseng
4	Tekanyo ea makoloi	E lekanya lebelo la li-motor tse 4 ka bo eona.
5	Tsitsisa Electrodes	E lekanya ka nepo boemo ba li-electrode ka ho tsoa ha ARC.
6	Arc Calibration	E lekanya matla a arc le boemo ba ho kopanya fiber ka boits'oaro.

Fetola Li-Electrode

• Ha li-electrode li ntse li felloa ke matla nakong ea ts'ebetso ea ho kopanya ha nako e ntse e feta, oxidation ea malebela a li-electrode e lokela ho hlahlojoa khafetsa. Ho khothalletsoa hore li-electrode li nkeloe sebaka ka mor'a ho tsoa ha 4500 arc.
• Ha palo ea ho tsoa ha arc e fihla palo ea 5500, molaetsa o khothalletsang ho khutlisa li-electrode o hlaha hang ka mor'a ho bulela matla. Ho sebelisa li-electrode tse tsofetseng ho tla fella ka tahlehelo e phahameng ea splice le ho fokotsa matla a splice.

Mokhoa oa ho Fetola

• Khetha [Emela Li-Electrode] ho [Menu ea Tlhokomelo].
• Melaetsa ea litaelo e tla hlaha skrineng. Ebe, tima splicer. Tlosa li-electrode tsa khale.

1. Tlosa likoahelo tsa electrode
2. Ntša li-electrode ho tsoa likoahelong tsa li-electrode

Hloekisa li-electrode tse ncha ka gauze e hloekileng e kolobisitsoeng ka joala kapa lithane tse se nang letlapa, 'me u li kenye ka har'a splicer.

1. Kenya li-electrode ka har'a likoahelo tsa li-electrode.
2. Kenya hape likoahelo tsa eleketrode ka har'a splicer, 'me u tiise li-screw.

• Hlokomela: U se ke ua tiisa ka ho feteletseng likoahelo tsa electrode.
• INNO Instrument e khothalletsa ka matla basebelisi bohle ho etsa [Stabilize Electrodes] le ho tlatsa [Arc Calibration] ka mor'a ho fetola electrode ho boloka liphello tse ntle tsa splice le matla a splice (lintlha li hlalositsoe ka tlase).

Tsitsisa Ts'ebetso ea Ts'ebetso ea Electrodes

• Khetha [Ho tsitsisa li-electrode].
• Beha likhoele tse lokisitsoeng ka har'a splicer bakeng sa ho kopanya.
• Tobetsa konopo ea [S] 'me splicer e tla qala ho tsitsisa li-electrode ka bo eona ka mekhoa e latelang:
• Pheta arc ho tsoa ka makhetlo a mahlano ho lekanya boemo ba arc.
• Etsa splicing ka makhetlo a 20 ka tatellano ho theha hantle boemo ba li-electrode

Tekanyo ea makoloi

Li-motor li fetoloa fekthering pele li romelloa, leha ho le joalo litlhophiso tsa tsona li ka hloka ho lekanyetsoa ha nako e ntse e ea. Ts'ebetso ena e lekanya li-motor tsa khatiso ka bo eona.

Mokhoa oa ts'ebetso

• Khetha [Motor Calibration] ho [Maintenance Menu].
• Laela likhoele tse lokisitsoeng ka har'a splicer ebe o tobetsa konopo ea [Set].
• Li-motor tsa khatiso li lekanyetsoa ka bo eona. Ha ho phethiloe, molaetsa oa katleho o tla hlahisoa.
• Hlokomela: Etsa mosebetsi ona ha phoso ea "Mafura" kapa "Thin" e etsahala, kapa ho tsamaisana le fiber kapa ho tsepamisa maikutlo ho nka nako e ngata haholo.

Mokhoa oa Ts'ebetso ea Arc Calibration

• Ka mor'a hore u khethe [Arc Calibration] ho menu ea tlhokomelo, setšoantšo sa [Arc Calibration] se tla hlahisoa skrineng.
• Seta likhoele tse lokisitsoeng holim'a splicer, ebe o tobetsa konopo ea [Set] ho qala ARC Calibration.
• Hlokomela: Sebelisa fiber e tloaelehileng ea SM bakeng sa ho lekanya arc.
• Netefatsa hore likhoele li hloekile. Lerōle le holim'a fiber le ama arc calibration.
• Kamora ho lekanyetsoa ha Arc, lipalo tse 2 tsa linomoro li tla hlahisoa skrineng.
• Ha boleng bo ka lehlakoreng le letona e le 11±1, splicer e tla hlahisa molaetsa hore o phethoe, ho seng joalo likhoele li hloka ho aroloa hape bakeng sa Arc Calibration ho fihlela molaetsa ho fihlela ts'ebetso e phetheloa ka katleho.
• Ka tlhahlobo ea litšoantšo, splicer e lemoha lerōle le litšila ho lik'hamera tsa splicer, le lilense tse ka 'nang tsa fella ka ho lemoha fiber e sa lokelang.
• Mosebetsi ona o hlahloba litšoantšo tsa khamera bakeng sa boteng ba litšila le ho hlahloba hore na li tla ama boleng ba splicing.

Mokhoa oa ts'ebetso

• Kgetha [Ho hlahloba lerole] ho [Tlhahiso menu].
• Haeba likhoele li behiloe ka har'a splicer, li tlose ebe u tobetsa [Set] ho qala ho hlahloba lerole.
• Haeba lerōle le fumanoa nakong ea ts'ebetso ea ho hlahloba lerōle, molaetsa o reng "O hlōlehile" o tla hlahisoa skrineng. Ebe u hloekisa lilense, 'me [Cheka Lerōle] ho fihlela molaetsa o reng “Fetsa” o hlaha skrineng.
• Hlokomela: Haeba tšilafalo e ntse e le teng ka mor'a ho hloekisa lilense tsa sepheo, ka kopo ikopanye le morekisi ea haufi le uena.
• Li-electrode li khothaletsoa hore li nkeloe sebaka ke tse ncha ha Current Arc Count e feta 5500 ho netefatsa boleng ba splice.
• Kena ho [Menu ea Tlhokomelo] > [Fetola Li-Electrode] > [Mekhoa ea Motlakase].
• Beha tlhokomeliso ea electrode le temoso ea electrode.

Paramethara	Tlhaloso
Tlhokomeliso ea motlakase	Ha palo ea ho tsoa ha electrode e feta palo e behiloeng, molaetsa o reng "Hlokomela! Fetola li-electrode" li tla hlaha ha u qala fusion splicer. Parameter e khothalletsoa hore e behoe e le "4500".
Temoso ea elektrode	Ha palo ea ho tsoa ha electrode e feta palo e behiloeng, molaetsa "Temoso! Fetola li-electrode" li tla hlaha ha u qala fusion splicer. Parameter ena e khothalletsoa hore e behoe e le "5500".

Ntlafatsa Software

• U tla tlameha ho ea ho View 5X leqepheng la sehlahisoa ho www.innoinstrument.com ebe u khoasolla software e ntlafalitsoeng file ho tsoa leqepheng lena.
• Hang ha e jarollotsoe, kenya faele ea file ho USB drive.
• Ebe o hokela drive ea USB ka har'a splicer ebe o kenya faele files.
• Kgetha [Apdate Software] sebopehong sa [System Setting].
• Kamora hore o tobetse [OK], splicer e tla qala ts'ebetso ea ntlafatso ka bo eona.
• Splicer e tla qala hape kamora hore ntlafatso e phetheloe.

View Motsamaisi oa Pro le Taolo ea Sesebelisoa

The View Pro Manager (VPM) ke sethala se felletseng sa maru se etselitsoeng ho hlophisa le ho laola merero ea fusion splicing le matlotlo a amanang. E fana ka lisebelisoa bakeng sa tsamaiso ea morero, ho latella thepa, le tlhahlobo ea data, ho netefatsa ho kopanngoa le ho hokahanya mesebetsing e fapaneng ea ho kopanya. VPM e lumellana le li-splicers tsa rona, ho kenyeletsoa le View Pro, View X, le M+ Series, e lumellang basebelisi ho ntlafatsa phallo ea bona ea mosebetsi le ho ntlafatsa tlhahiso ka taolo e ntlafalitsoeng ea data le bokhoni ba ho beha leihlo ka nako ea nnete.

Mokhoa oa ho ngolisa sesebelisoa sa hau

• U tla hloka ho kenya SIM Card ho Fusion Splicer ea hau.
• Eya ho [System Setting]
• Tsamaisetsa tlase leqepheng la bobeli
• Etsa bonnete ba hore "Network" e BUTSE
• Boemo ba hona joale ba marang-rang bo ka netefatsoa ho lets'oao la GPS la Workbench e kanna ea se be teng ka tlung.
• Haeba tshebetso ya netweke e hloleha, eya ho "Network Settings" mme o kenye dintlha tsa APN ka bowena. Sheba ho mofani oa SIM card bakeng sa lintlha tse nepahetseng tsa APN
• GPS le Netweke ditshebetso di bulelwa ka ho sa feleng. U ka fetola likhetho tsa khokahanyo ho "System Setting" -> "Network ON/OFF" le "GPS ON/OFF".
• Ho latedisa ho fumaneha hape ha sesebediswa se tinngwe ka beteri e kentsweng. O ka fetola ts'ebetso ena ka khetho ea "GPS Tracking ha motlakase o tima".

Khokahano ea Khalendara

• Ka har'a li-setting tse ho [Main Menu] ea splicer, u tla khona ho [Beha Khalendara]
• Ka ho kenya Khalendara Sync, fusion splicer e tla beoa nako ea netweke ea lehae ka bo eona
• Ha Calendar Sync e kentsoe tshebetsong, Khalendara e ke ke ya hlophiswa ka bowena

Mookameli oa Mokhoa

• Eya ho [Main Menu] le [Lintlha tsa Tsamaiso]
• Ho fihlella Menu ea Moemo oa Mookameli tobetsa 5 x [Lintlha tsa Tsamaiso]
• Ha ho na password ea kamehla. Tlohela Phasewete e se na letho bakeng sa ho seta ha qalong

Senotlolo sa Menu

• Ha o le ho Menu ya Moemedi wa Mohlokomedi, Menu Lock e o dumella ho thibela phihlello ho di-setting tse fapaneng
• Notlela Lenane la Lehae: Thibela ho kena ho Main Menu
• Notlela Menu ea Mokhoa oa Splice: Fokotsa ho kena ho menu eohle ea Splice Mode
• Notlela Khetha Mokhoa oa ho arohana: Fokotsa phihlello ho khetha Mefuta ea Splice
• Notlela Mokhoa oa ho Fetola Karolo: Fokotsa phihlello ea ho edita Mekgwa ya Splice
• Notlela Hlakola Mokhoa oa ho Hlakola: Fokotsa phihlello ho hlakola Mekhoa ea Splice
• Notlela Lenane la Phoso la ho Itlhokomoloha: Fokotsa phihlello ho bulela/tima likhetho tsa liphoso tsa ho iphapanyetsa
• Notlela Hlakola Rekoto ea Likhahla: Fokotsa phihlello ea ho hlakola Lirekoto tsa Splice
• Lock Menu ea Tlhokomelo: Beha monyetla oa ho kena ho Menu ea Tlhokomelo
• Lock Mode Menu ya Heater: Thibela ho kena ho Menu ea Mokhoa oa Heater
• Notlela Mokhoa oa ho futhumatsa mocheso: Fokotsa phihlello ho edita Mefuta ea Heater
• Notlela Mokhoa oa ho Fetola Heatere: Fokotsa phihlello ho edita Mefuta ea Heater
• Notlela Mokhoa oa ho Hlakola Heater: Fokotsa phihlello ho hlakola Mekhoa ea Heater
• Notlela Menu ea Litlhophiso tsa Sisteme: Fokotsa ho kena ho Setting ea Sistimi

Litlhophiso tsa Sisteme ho Menu ea Mookameli

• Ka har'a Litlhophiso tsa Sistimi ho [Menu ea Mookameli], o ka seta sisteme bocha ho li-setting tsa feme
• Sebelisa Global Cleave Angle Limit: Kenya Cleave Angle ho fokotsa ts'ebetso ea splice kapa ho hlahisa molaetsa oa phoso ha angle ea cleave e le kholo ho feta boleng bo sebelisitsoeng.
• Khatiso ea pele ea Arc: Kenya ts'ebetso ho qobella ts'ebetso ea Arc Calibration hang ka letsatsi
• Thibela Phoso ea Phapang Hlokomoloha: Fokotsa bokhoni ba ho feta bofokoli ba fiber le ho tsoela pele ka ho kopanya
• Thibela Cleave Angle ERR Hlokomoloha: Fokotsa bokhoni ba ho hlakola liphoso tsa cleave angle le ho tsoela pele ka ho kopanya
• Thibela Pheta-pheta ea Arc: Thibela mosebetsi ho hlahisa arc e 'ngoe ka mor'a ho kopanya

Fetola Phasewete ho Menu ea Mookameli

• Ka har'a Litlhophiso tsa Sistimi ho [Menu ea Mookameli], o ka seta Lekunutu le lecha la Mohlokomeli.
• Ha ho na password ea kamehla. Tlohela Phasewete e se na letho bakeng sa ho seta ha qalong
• O ka seta phasewete o sebedisa motswako wa ditlhaku, dinomoro, le ditlhaku tse ikgethang, ho fihla ho ditlhaku tse 8

Ho notlela Nako ho Menu ea Mookameli

• Mookameli a ka beha phasewete mme a bolela letsatsi leo mochine o tla koala ka lona
• Tobetsa konopo ea "+" ho kenya ntho e ncha, kapa konopo ea "x" ho hlakola se seng se ntse se le teng
• Ho ka hlalosoa linotlolo tsa nako tse 6 tse fapaneng
• Kopo ea Tšebeletso
• Ka har'a [Maintenance Menu] joale u ka fana ka Kopo ea Tšebeletso
• Ho romela Kopo ea Ts'ebeletso, tobetsa konopo ea "OK" e tla romella kopo ea hau ho Sehlopha sa Tšebeletso sa Bareki ba INNO Instrument.
• Sehlopha sa Tšebeletso sa Bareki sa INNO Instrument se tla netefatsa taba ena ka sistimi ea tlhahlobo e hole
• Molaetsa o tla sala ho splicer ho tataisa mosebelisi mehatong ea ho rarolla bothata
• Ho tobetsa konopo ea "OK" ha ho fane ka maikutlo hang hang. Haeba u sa fumane molaetsa ofe kapa ofe o tsoang ho INNO, ka kopo, tobetsa konopo ea kopo hape kapa u ikopanye le e mong oa InNO's Authorized Partners kapa INNO Instrument Customer Service Team ka ho toba.

Molaetsa wa Tshebeletso

• Melaetsa eohle e tsoang ho View Pro Manager li bolokiloe ho menu ena
• Sena se kenyelletsa melaetsa e tobileng, melaetsa ea sistimi ea seva, le melaetsa ea Ts'ebeletso ea Bareki ba INNO

Setšoantšo sa skrini

• Ho nka skrini, ka potlako tobetsa konopo ea "Power Button" habeli.
• Pontšo ea hajoale e tla nkuoa ebe e bolokoa karolong ea [Screenshot]
• Ho kenya setšoantšo ho View Seva ea Pro Manager, tobetsa konopo ea [Upload]
• Haeba konopo e nepahetseng e fetoha Green, setšoantšo se kentsoe ka katleho ho seva
• Haeba konopo e ka ho le letona e le putsoa, ​​setšoantšo se ntse se kentsoe

Ho romella melaetsa

• Hao splicer ka fumana melaetsa ho tswa ho View Sistimi ea Motsamaisi oa Pro
• Ha molaetsa o amohetswe, o tla bona aekhone ya molaetsa e hlahiswa bareng e ka hodimo
• U tla hloka ho kenya hape bencheng ea mosebetsi ho bona molaetsa, molaetsa o tla hlahisoa joalo ka pop-up.

Lisebelisoa

Tlhophiso ea Sistimi

Paramethara	Tlhaloso
Buzzer	E beha molumo oa molumo.
Setsi sa Mocheso	E beha yuniti ea mocheso.
Automatic Heating	Haeba e setetsoe ho [E butswe], ha fiber e kenngwa ka hara hitara. Mofuthu o tla futhumatsa ka bohona.
Lerole Hlahloba	Sheba hore na ho na le lerōle sebakeng sa litšoantšo. E beha ts'ebetso ea ho hlahloba lerōle, OFF ka kamehla. Haeba e setetsoe ho ON, tlhahlobo ea duct e tla etsoa ka bo eona ha splicer e buletsoe.
Hula Teko	E beha teko ea ho hula, ho ON ka ho sa feleng, haeba e behiloe ho OFF, teko ea ho hula e ke ke ea etsoa.
LED e tšoeu	Leseli la LED le tšoeu.
Senotlolo sa senotlolo	E nolofalletsa tšireletso ea password.
Seta bocha	E khutlisetsa litlhophiso tsa feme.
Ntlafatsa Software	Mokhoa oa ho ntlafatsa software ea Splicer.
Puo	E beha puo ea sistimi.
Khetho ea ho Boloka Matla	E beha nako ea [Monitor Shut Down], nako ea [Splicer Shut Down], le khanya ea LCD.
Beha Khalendara	E beha nako ea sistimi.
Fetola senotlolo	Khetho ea ho fetola phasewete. 0000 password ea kamehla.

Khetho ea ho Boloka Matla

Haeba ts'ebetso ea ho boloka matla e sa setelloa nakong ea ts'ebeliso ea betri, palo ea li-splice cycles e tla fokotseha.

1. Khetha [Khetho ea ho Boloka Matla] ho menu ea [System Setting].
2. Fetola linako tsa [Monitor Shut Down] le [Splicer Shut Down]

Paramethara	Tlhaloso
Lekola Koala	Ho boloka matla a betri, ho bulela tšobotsi ena ho tla tima skrine ka bohona haeba splier e sa sebelisoe ka nako e behiloeng. Ha skrini se tima, u tla bona lebone le benyang haufi le konopo ea matla. Tobetsa konopo efe kapa efe ho bulela skrini hape.
Splicer Koala	Ka tsela e iketsang e koala matla a splicer haeba a lula a sa sebetse ka nako e behiloeng. Sena se thusa ho qoba ho tsoa ha betri.

Lintlha tsa Tsamaiso

Kamora ho khetha [Lintlha tsa Tsamaiso], melaetsa e latelang e tla bontšoa skrineng:

Paramethara	Tlhaloso
Mochini oa serial NO.	E bonts'a nomoro ea seriale ea fusion splicer.
Software Software	E bonts'a mofuta oa software ea fusion splicer.
Mofuta oa FPGA	E bonts'a mofuta oa FPGA.
Kakaretso ea Arc Count	E bonts'a palo eohle ea ho tsoa ha arc.
Palo ea Arc ea Hona joale	E bonts'a palo ea ho tsoa ha arc bakeng sa sete ea hajoale ea li-electrode.
Tlhokomelo ea ho Qetela	E hlahisa letsatsi la ho qetela la tokiso.
Letsatsi la Tlhahiso	E hlahisa letsatsi la tlhahiso.

Sehlomathiso I

Phahameng Tahlehelo ea karolo: Sesosa le pheko

• Hlokomela: Ha o kopanya likhoele tse fapaneng tsa optical tse nang le li-diameter tse fapaneng kapa li-multi-mode fibers, mohala o otlolohileng, o bitsoang "splicing line," o ka hlaha.
• Ke habohlokoa ho hlokomela hore sena ha se ame boleng ba splicing, ho kenyelletsa tahlehelo ea splicing le matla a ho kopanya.

Lethathamo la Melaetsa ea Phoso

• Ha u ntse u sebelisa splicer, u ka 'na ua kopana le molaetsa oa phoso skrineng. Latela litharollo tse thathamisitsoeng ka tlase ho rarolla bothata.
• Haeba bothata bo ntse bo tsoela pele 'me bo ke ke ba rarolloa, ho ka ba le liphoso ho fusion splicer. Maemong a joalo, ho bohlokoa ho buisana le setsi sa hau sa thekiso bakeng sa thuso e eketsehileng.

Molaetsa oa Phoso	Lebaka	Tharollo
Phoso ea Left Fiber Place	Sefahleho sa ho qetela sa fiber se behoa holim'a kapa ka ntle ho "electrode centerline".	Tobetsa konopo ea "R", 'me u behe sefahleho sa fiber end-fiber pakeng tsa electrode centerline le V-groove edge.
Phoso ea Sebaka sa Fiber se nepahetseng
Tobetsa Motor Distance Over Limit	Fiber ha e behe ka nepo V-groove. Fiber ha e fumanehe tšimong ea Khamera ea view.	Tobetsa konopo ea "R" 'me u behe fiber hape.
Tobetsa Motor Error	Enjene e kanna ea senyeha.	Ikopanye le Sehlopha sa Botekgeniki se haufi sa INNO.
Sefahleho sa Fiber End se hlolehile	Fiber ha e behe ka nepo V-groove.	Tobetsa konopo ea "R" 'me u behe fiber hape.
Ho hloleha ha Arc	Arc Discharge ha ea etsahala.	Netefatsa hore li-electrode li maemong a nepahetseng. Fetola li-electrode.
Lokisa Bohole ba Motor ho Feta Moeli	Fiber ha e behe ka nepo V-groove.	Tobetsa konopo ea "R" 'me u behe fiber hape.
Ho Batla Fiber Clad ho hlolehile	Fiber ha e behiloe ka nepo ka tlase ho V-groove.	Tobetsa konopo ea "R" 'me u behe fiber hape.
Fiber Clad Gap e Fosahetse	Ho na le lerole kapa litšila holim'a fiber	Lokisetsa fiber (ho hlobolisa, ho hloekisa le ho qhaqha) hape.
Mofuta o sa Tsejoeng oa Fiber	Ho na le lerole kapa litšila holim'a fiber	Lokisetsa fiber (ho hlobolisa, ho hloekisa le ho qhaqha) hape.
	Li-Fibers tse sa tšoaneng	Sebelisa mokhoa o nepahetseng oa ho kopanya ntle le mokhoa oa AUTO oa ho kopanya hape.
	Likhoele tsa optical tse sa tloaelehang	AUTO splice mode e ka tseba feela likhoele tse tloaelehileng joalo ka SM, MM, NZ.
Fiber Clad Over Limit	Fiber ha e fumanehe tšimong ea Khamera ea view.	Fetola boemo ba faeba 'me u qete [Motor Calibration] bakeng sa tlhokomelo.
Focus Motor Home boemo ba Erro	The fusion splicer e otloa ke matla nakong ea ts'ebetso ea ho kopanya.	Etsa [Motor Calibration] bakeng sa tlhokomelo. Haeba bothata bo ntse bo sa khone ho rarolloa, ikopanye le Sehlopha sa hau sa lehae sa INNO.
Fiber End face Gap Fosahetse	Litlhophiso tsa [Ho fetella] li ngata haholo	Fetola kapa u qalelle litlhophiso tsa [Overlap].
	Enjene ha e lekane	Etsa [Motor Calibration] tlhokomelo.
Motor Distance Over Limit	Fiber ha e behe ka nepo V-groove.	Tobetsa konopo ea "R" 'me u behe fiber hape.
	Ho na le lerole kapa litšila holim'a fiber	Lokisetsa fiber (ho hlobolisa, ho hloekisa le ho qhaqha) hape.
	Ho na le lerole kapa litšila holim'a fiber	Etsa [Dust Check] ka mor'a ho hloekisa lilense le liipone.
Fiber e sa lumellaneng	Likhoele tse mahlakoreng a mabeli ha li tšoane	E ka fella ka tahlehelo e kholo ea splice haeba u tsoela pele ho kopanya, Ka kopo sebelisa mokhoa o nepahetseng oa splice o tsamaellanang le likhoele.
Cleave Angle Over Limit	Sefahleho sa fiber e mpe	Lokisetsa fiber (ho hlobolisa, ho hloekisa le ho petsoha) hape.Sheba boemo ba fiber cleaver. Haeba lehare le koahetse, fetola lehare sebakeng se secha.
	[Cleave Limit] e behiloe tlase haholo.	Eketsa "Cleave Limit" (boleng bo tloaelehileng: 3.0 °)
Core Angle Over Limit	[Offset Limit] e behiloe tlase haholo.	Eketsa "Core Angle Limit" (boleng bo tloaelehileng: 1.0 °).
	Lerōle kapa litšila li holim'a V-groove kapa clamp chip.	Hloekisa V-groove. Lokisetsa le ho beha fiber hape.

Khokahano ea Fiber Axis e hlolehile	Axial offset (>0.4um)	Lokisetsa fiber (ho hlobolisa, ho hloekisa, le ho petsoha) hape.
	Enjene ha e lekane	Etsa tlhokomelo ea [Motor Calibration].
Fiber e Silafetse	Ho na le lerole kapa litšila holim'a fiber	Lokisetsa fiber (ho hlobolisa, ho hloekisa, le ho petsoha) hape.
	Lerole kapa litšila li holim'a lense kapa li-LED	Phetha [Tlhahlobo ea Lerōle]. Haeba lerōle kapa litšila li le teng, hloekisa lilense kapa li-LED
	"Ho hloekisa nako ea Arc" e khuts'oane haholo	Beha "Ho hloekisa nako ea Arc" ho 180ms
	Hlophisa likhoele tsa mantlha tseo ho leng thata ho li fumana u sebelisa mokhoa oa ho hokahanya ha mantlha nakong ea ho kopanya.	Arola likhoele tseo ho leng thata ho li fumana ka MM splice mode (cladding layer alignment).
Fat Splicing Point	Litlhophiso tsa [Ho fetella] li ngata haholo	Fetola kapa qala ho "Overlap".
	Enjene ha e lekane.	Lekanya matla a arc ka ts'ebetso ea [Arc Calibration].
Thin Splicing Point	Matla a sa lekaneng a arc	Lekanya matla a arc ka ts'ebetso ea [Arc Calibration].
	Matla a pre-fuse kapa nako e behiloe holimo haholo	Fetola kapa qala litlhophiso tsa "Pre-fuse Power" kapa "Pre-fuse Time".
	Sethapo sa "Overlap" e sa lekaneng	Fetola kapa u qalelle litlhophiso tsa [Overlap]

• Litharollo tsa mathata a mang a tloaelehileng li fanoe ka tlase bakeng sa referense ea hau.
• Haeba u sa khone ho rarolla mathata, ka kopo ikopanye le moetsi ka kotloloho bakeng sa thuso.

1. Matla ha a time ha o tobetsa konopo ea "ON/OFF".
   1. Tobetsa 'me u tšoare senotlolo "ON / OFF" ho fihlela LED e bonesa, lokolla konopo 'me splicer e tla tima.
2. Litaba tse nang le splicer tse khonang feela li-splicies tse 'maloa tse nang le betri e tjhakiloeng ka botlalo.
   • Matla a betri a ka fokotseha ha nako e ntse e ea ka lebaka la memori le polokelo e atolositsoeng. Ho sebetsana le sena, ho kgothaletswa ho tjhaja betri ka mora ho e dumella hore e tswe ka botlalo.
   • Pakete ea betri e fihlile pheletsong ea bophelo. Kenya pakete e ncha ea betri.
   • Se ke oa sebelisa betri ka mocheso o tlase.
3. Molaetsa oa phoso o hlaha sebonong.
   • Sheba sehlomathiso ll.
4. Tahlehelo e phahameng ea splice
   • Hloekisa li-V-grooves, fiber clamps, li-LED tse sireletsang moea, le lilense tsa khamera.
   • Fetola li-electrode.
   • Sheba sehlomathiso l.
   • Tahlehelo ea splice e fapana ho ea ka angle ea cleave, maemo a arc le bohloeki ba fiber.
5. Monitor e ile ea tima ka tšohanyetso.
   • Ho nolofalletsa ts'ebetso ea ho boloka matla ho etsa hore splicer e kene sebakeng sa matla a tlase kamora nako e telele ea ho se sebetse. Tobetsa konopo efe kapa efe ho e tlosa boemong ba standby.
6. Motlakase oa Splicer o ile oa tima ka tšohanyetso.
   • Ha o nolofalletsa ts'ebetso ea ho boloka matla, splicer e tla tima motlakase oa splicer kamora nako e telele ea ho se sebetse.
7. Phapang lipakeng tsa Khakanyo ea tahlehelo ea splice le Tahlehelo ea sebele.
   • Tahlehelo e lekantsoeng ke tahlehelo e baliloeng, kahoo e ka sebelisoa bakeng sa litšupiso feela.
   • Likarolo tsa optical tsa splicer li ka 'na tsa hloka ho hloekisoa.
8. Sleeve ea tšireletso ea fiber ha e fokotsehe ka ho feletseng.
   • Eketsa nako ea ho futhumatsa.
9. Mokhoa oa ho hlakola mokhoa oa ho futhumatsa.
   • Tobetsa konopo ea "HEAT" ho hlakola mokhoa oa ho futhumatsa.
10. Sleeve ea tšireletso ea fiber e khomaretse poleiti ea ho futhumatsa ka mor'a ho honyela.
    • Sebelisa swab ea k'hothone kapa ntho e tšoanang e bonolo ho sutumelletsa le ho tlosa letsoho.
11. U lebetse li-password.
    • Ikopanye le sehlopha sa hau sa botekgeniki se haufi sa INNO Instrument.
12. Ha ho phetoho ea matla a arc kamora [Arc Calibration].
    • Ntho e ka hare e lekantsoe le ho lokisoa bakeng sa tlhophiso ea matla a arc e khethiloeng. Matla a arc a bontšitsoeng ka mokhoa o mong le o mong oa splice o lula a sa fetohe.
13. Lebala ho kenya fiber ea optical nakong ea ts'ebetso ea ts'ebetso ea tlhokomelo.
    • U tla hloka ho bula sekoahelo se thibelang moea 'me u behe likhoele tse lokiselitsoeng V-groove ebe u tobetsa konopo ea "SET" kapa "R" ho tsoela pele.
14. E hloleha ho ntlafatsa
    • Ha basebelisi ba sebelisa "USB" e ncha ho ntlafatsa, splicer e kanna ea se khone ho tseba lenaneo la ntlafatso ka nepo. file; o hloka ho seta USB Drive bocha ebe o qala splicer hape.
    • Hlahloba hore na apkreite file lebitso le sebopeho li nepahetse.
    • Haeba u sa khone ho rarolla mathata, ka kopo ikopanye le moetsi ka ho toba.
15. Ba bang
    • Ka kopo ikopanye le moetsi ka kotloloho.

• Mefuta ea sehlahisoa le litlhaloso li ka fetoha ntle le tsebiso pele.
• Copyright © 2024 INNO Instrument Inc. Litokelo tsohle li sirelelitsoe.
• Litlhaloso tsa likarolo tsa INNO Instrument Inc.
• support@innoinstrument.com
• Leqephe la lapeng
• www.INNOinstrument.com
• Ka kopo, re etele ho Facebook
• www.facebook.com/INNOinstrument

Litokomane / Lisebelisoa

INNO Instrument 3X Active V Groove Cladding Alignment Fusion Splicer [pdf] Bukana ea Mosebelisi 3X, 5 Pro, 3X Active V Groove Cladding Alignment Fusion Splicer, 3X, Active V Groove Cladding Alignment Fusion Splicer, V Groove Cladding Alignment Fusion Splicer, Cladding Alignment Fusion Splicer, Alignment Fusion Splicer, Fusion Splicer, Splicer

Litšupiso

• Bukana ea Mosebelisi