FUNLAB FF01 Hall Effect Controller
Fetileview
Firefly Pro Controller–Instruction Manual
Tlhaloso ea Sehlahisoa
| Sehlopha | Tlhaloso |
| Mohlala | FF01 |
| Phetisetso Medium | Bluetooth 2.1 |
| Maqhubu a Carrier | 2.402-2.480GHz |
| Protocol | Bluetooth BT2.1+EDR |
| LED | Li-LED tse 4 le Mabone a Mebala a Mengata |
| Betri | A Polymer Lithium Battery 3.7V/950mAH |
| Nako ea Mamello | Lihora tse 12.5 (Mabone a Timiloe) |
| Nako ea ho tjhaja | Lihora tse 6.3 |
| Sebetsa Voltage | 3.7V-4.2V |
| Ho tjhaja Voltage | 5V |
| Mocheso oa Mosebetsi | -10 ° C ~ 50 ° C |
| Mocheso oa polokelo | -20°c-10°c |
Ts'ebetso ea ho Bula/Ho tima ea Molaoli (Tlas'a Switch Mode)
Khokahano e Wiring
Khokahano e se nang mohala
- Ho tsoa ho HOME Menu, khetha Controllers, ebe Fetola Grip le Order.
- Press and hold Y + HOME for 3 seconds, and 4 LED lights flash quickly.
The LED(s) are becoming stable, pairing finishes. - If no pairing for over 2.5 minutes, it shuts down by itself.
- If paired and no operation for over 5 mins, shuts down by itself. (No movement on the sensor).
Mosebetsi oa Tsoha: Press the Home Button, and then the console in the sleep state can be woken up and connected again.
Mokhoa oa Ts'ebetso le Letšoao la LED (Taelo ea Khokahano)
Mokhoa oa ho Pairing
- Combination Pairing: In the off state, press and hold the following key combination to enter the Pairing Mode.
- Android Mode: A+ HOME
Lebone la LED2 - LED3 ka potlako ha le kopanya, 'me LED2 - LED3 e tsoela pele ha e ntse e kopanya ka katleho; - Fetoha Mokhoa: Y + HOME
LED1 – LED4 flash quickly while pairing, and the console automatically assigns when pairing is successful. - PC Mode: B + HOME
LED1 & LED4 flash quickly while pairing, and LEDl & LED4 keep on while pairing successfully; - iOS Mode: B+ HOME
LED1 & LED4 flash ka potlako ha e ntse e kopanya, 'me LED1 & LED4 e tsoela pele ha e ntse e kopanya ka katleho (Sistimi ea tšehetso: iOS 13.6 kapa ka holimo/iPadOS 13.6 kapa ka holimo); - Steam Deck Mode: Press the “STEAM” Button on the left side of the console – “Settings” -“Bluetooth” to connect
B + LAPENG - Lebone la LED1 le LED4 le potlakile ha li para, 'me LED1 le LED4 li lula li sebetsa ha li ntse li tsamaisana ka katleho.
Mosebetsi oa Turbo le AUTO TURBO
Ka Mokhoa ofe kapa ofe
- Likonopo li ka hlophisoa ho Mosebetsi oa TURBO: A/B/X/Y/L/R/ZL/ZR/D-pad Button
- (For the 1st time) Press the TURBO Button+ one of the function buttons to achieve the Manual TURBO Function (Press and hold to launch continuously)
- (For the 2nd time) Press the TURBO Button+ one of the function buttons to achieve the Automatic TURBO Function (Automatically continuous launch)
- (For the 3rd time) Press the TURBO Button+ one of the function buttons to clear the TURBO Function (Clear)
- Hlokomela: Press and hold the TURBO Button for 5 seconds (if the Vibration intensity is not 0%, there will be a vibration cue ) to clear all TURBO Functions.
TURBO Speed Adjustment (Maemo a 3)
- Mekhoa ea ho fetola:
- Press TURBO Button+ “Shake L/R Joystick Up”, increase speed by 1 level;
- Press TURBO Button+ “Shake L/R Joystick Down “, reduce speed by 1 level;
Maemo a Lebelo:
- Tsoela pele ho qala makhetlo a 5 ka motsotsoana (Boemo ba 1);
- Tsoela pele ho qala makhetlo a 12 ka motsotsoana (Boemo ba 2);
- Tsoela pele ho qala makhetlo a 20 ka motsotsoana (Boemo ba 3);
Mosebetsi oa ho fetola Vibration
- Press the Motor Vibration Button on the back of the controller, and you can adjust the Motor Vibration Intensity. Vibration Intensity can be cycled in turn. There are 5 intensities, 100%, 75%, 50%, 25% and 0%.
Reset ea The Controller Hardware
- There is a small hole on the back of the controller, and it is the Reset Button. After pressing it, the controller hardware will reset.
Khokahano e ncha ea Molaoli
- When the controller is pairing to the previous device, you only need to press the HOME Button after the controller is in standby, and it will pair to the previous device.
Lipontšo tsa ho lefisa
- Charging in the OFF State: LED4 flashes slowly, and then turns off while being fully charged;
- Ho tjhaja ha o Hoketswe ho switjha: Mabone a dikanale a tsamaelanang a tla panya butle, ebe a tswela pele a ntse a tjhaja ka botlalo.
Lighting Control Instruction (Light Button
)
- Khantša mohlala o khanyang: Tobetsa ho
konopo. - Change the Light Color: Press, konopo.
Colors will change each time you press the konopo. - Change the Lighting Mode: Hold the,
Initial Mode: Always-on
1st time-click: breathing light mode
2nd time-click: quick flash mode
3rd time-click: vibration lighting mode
Back to Always-on: turn off and then turn on the light. - Turn OFF the light: Hold konopo bakeng sa metsotsoana e 5.
Turn ON the light: Press konopo.
Macro le Mosebetsi oa 'Mapa ho Li-buttons tsa The Back
Macro Function-Macro Likonopo
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the buttons you want to edit (up to 24 steps). The controller will have the vibration cue after loosening the MR Button and then pressing the XR Button to trigger the Macro Buttons.
- Press and hold the ML Button and don’t loosen (4 LED lights turn on, entering programming), inputting the buttons you want to edit (up to 24 steps). The controller will have the vibration cue after loosening the ML Button and then pressing the XL Button to trigger the Macro Buttons. Buttons that Macro Function could edit are A/B/X/Y/L/R/ZL/ZR/+/-/D-pad Buttons and L/Rjoysti cks (can be used as a combo in the game).
Likonopo tsa Mosebetsi oa 'Mapa-Programmable
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the single button you want to map. The controller will have the vibration cue after loosening the MR Button and then pressing the XR Button to trigger the Programmable Buttons.
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the single button you want to map. The controller will have the vibration cue after loosening ML Button, and then pressing XL Button to trigger Programmable Buttons; and Buttons that Map ping Function could edit are A/B/X/Y/L/R/ZL/ZR/+/-/D-pad Buttons L/Rjoysti cks.
Hlokomela:
- Ka Mosebetsi oa Memori;
- Press the MR/ML Buttons that set programming, and there is a vibration cue, and then you can clear the Macro and Mapping Function of the XR/XL Buttons.
Keylinker APP Instructions
- Open the app store and search for “Keylinker” to download the APP.
- Open the Bluetooth connection handle.
- APP KEYLINKER BLE appears, click, and connect successfully.
- Tobetsa aekhone ea li-setting ka ho le letona ho kenya leqephe la litlhophiso.
- O ka fetola Konopo ho APP, oa beha mabone, oa fetola ho thothomela, joalo-joalo
Tšehetso
- We promise to provide sustainable services for this controller. You can get more operational guidance support from our service channel and official web:
- Websebaka: www.funlabswitch.com
- Instagpheleu: funlab_official
- Tšebeletso: support@funlabswitch.com
- Discord:
Litokomane / Lisebelisoa
 |
FUNLAB FF01 Hall Effect Controller [pdf] Buka ea Taelo FF01, FF01 Hall Effect Controller, Hall Effect Controller, Effect Controller, Controller |