FAAC XR2 433 C Boto ea Taolo ea Moamoheli oa Kantle ea Mecha e Mebeli

Litlhaloso

• Phepelo ea motlakase: 12/24V AC-DC
• Maqhubu a ho Amohela: 433MHz (XR2 433 C) / 868MHz (XR2 868 C)
• Tšebeliso ea Hona Joale: 100mA
• Decoding: DS-LC-SLH (XR2 433 C) / DS-SLH (XR2 868 C)
• Likhoutu tse ka Hopoloang: 250
• Nomoro ea Likanale: 2
• Palo ea Liphetho tsa Phetiso (NO): 2
• Mofuta oa tlhahiso: HA HO tšusumetso (CH1), HA HO tšusumetso / e tsitsitseng (e khethiloeng) (CH2)
• Boholo ba Mojaro: 0.5A / 120VA
• Tekanyetso ea Tšireletso: IP44
• Thempereichara ea ho sebetsa: -20°C ho ea ho +55°C

Litaelo tsa Tšebeliso ea Sehlahisoa

Radio Commands Memori

1. Khetha motsoako o lakatsehang oa li-switches tse 12 tsa DIP ho remote control ea DS.
2. Tobetsa konopo ho seamoheli se tsamaellanang le kanale eo u batlang ho amahanya remoutu le eona motsotsoana o le mong.
3. LED e lumellanang le moamoheli e tla qala ho benya butle ka metsotsoana e 5.
4. Ka metsotsoana ena e 5, tobetsa konopo e batloang ho remote control.

Mehato e ts'oanang e ka lateloa bakeng sa ho tšoara litaelo tsa seea-le-moea tsa SLH le LC ka hlooho joalo ka ha ho hlalositsoe bukeng ea mosebelisi.

Ho hlakoloa ha Litaelo Tsohle tsa Radio

1. Tobetsa 'me u tšoare konopo ho seamoheli metsotsoana e ka bang 5 ho fihlela LED e tsamaisanang le eona e bonesa butle-butle.

Mokhoa oa ho sebetsa

Sesebediswa se dumella ditaolo tse fapaneng tsa radio ho sebetsa dikanale tse fapaneng. Bakeng sa mohlalaample, remote control 1 e sebetsa mocha oa 1, 'me taolo ea remote 2 e sebetsa mocha oa 2.

TLHALOSO

• Boto ea taolo ea XR2 C ke moamoheli oa kantle oa likanale tse peli, tse nang le sistimi e kopaneng ea ho khetholla (DS, SLH, LC), e bitsoang OMNIDEC.
• Ha kanale e kentsoe tšebetsong ke taolo ea seea-le-moea (DS, SLH, LC), lebitso le amanang le NO relay le koala ka mekhoa e hlalositsoeng Khaolong ea 5.

Litlhophiso tse khethiloeng ke:

• CH1 = pulsed NO relay tlhahiso
• CH2 = pulsed/fixed NO relay tlhahiso (e khethiloe ke DS1)

1. Sebaka se entsoeng esale pele bakeng sa li-cable grippers
2. Sekoahelo
3. Sesebelisoa sa ho boloka ho tataiso ea DIN
4. Lisebelisoa tsa ho sireletsa li-screw
5. Li-terminals bakeng sa tlhahiso ea taelo (NO)
6. Ka tlwaelo bula (NO) relay kgokahanyo
7. Li-LED tse khannoang (ON= OUTPUT ACTIVE) DL1=LED CH 1 DL2=LED CH2
8. Likonopo tsa mananeo a seea-le-moea SW1=PUSH-BUTTON CH1 SW2=PUSH-BUTTON CH2
9. DS1:= Khetho ea dip-switch
10. Terminal ea phepelo ea motlakase
11. Terminal bakeng sa antenna
12. DL3: Lisebelisoa tsa LED ( ON = MAINS PRESENT )

DS1	ON	TLOA
DIP PHETHA 1	SEHLOOHO KHALE 2 TS'ELISO	TŠOANTŠO KHALE 2 HLAHALA
DIP PHETHA 2	SEBELISA	SEBELISA

LIEKETSENG MOKHOPO

	XR2 433 C	XR2 868 C
PHEPO EA MATLA (V)	12/24 ac-dc	12/24 ac-dc
KAMOHELO (MHz)	433.92 ±0.1	868.35±0.2
KHOETSOANG KHABANE (A)	100 mA	100 mA
DECODING (OMNIDEC SYSTEM)	DS-LC-SLH	DS-SLH
POLOKO LIKHOUTU	250	250
NUMBER OF LIEKETSENG	2	2
NUMBER OF RELAYO LIEKETSO (NO)	N 1 pulsed (CH1) N 1 pulsed/fixed (selectable) (CH2)	N 1 pulsed (CH1) N 1 pulsed/fixed (selectable) (CH2)
RELAYO LIEKETSENG MAKHONO	0.5 A / 120 VA	0.5 A / 120 VA
TS'IRELETSO TLELASE	IP44	IP44
TŠEBELETSO MOHLOMI MOCHESO MOCHESO (°C)	-20 / +55	-20 / +55

MEMORIZZAZIONE DEI RADIOCOMANDI

• Bongata, ke mofuta o le mong feela oa likhoutu tsa seea-le-moea o ka bang teng botong ea XR2 C.
• (DS, SLH, LC) .
• Boholo ba likhoutu tse 250, tse arotsoeng lipakeng tsa 1 le 2, li ka bolokoa mohopolong.

POLOKO EA KHOPOTSO EA MOLAOLI TSA DS RADIO

1. Taolong ea seea-le-moea sa DS, khetha motsoako o hlokahalang oa ON-OFF bakeng sa li-dip-switches tse 12.
2. Tobetsa motsotsoana o le 1 konopo e tobetsang ho seamoheli (Fig.1 ref 8) e amanang le kanale eo u lakatsang ho e amahanya le taolo ea radio.
3. LED e amehang ho moamoheli (setšoantšo sa 1, ref. 7) e qala ho hadima butle bakeng sa metsotsoana e mehlano.
4. Ka har'a metsotsoana ena e 5., Tobetsa konopo e loketseng ea ho tobetsa taolong ea radio.
5. LED e amehang (Fig.1 ref. 7) e khantša lebone le tsitsitseng bakeng sa motsotsoana oa 1 ebe e ea OFF, e bontšang hore polokelo e phethiloe.
   • Boto e tla romela taelo ho sehlahisoa se amanang le mocha.
6. Ho kenya ditaolo tse ding tsa radio, seta motswako o tshwanang wa ON - OFF o sebelisitsoeng ntlheng ea 1).

POLOKO EA SEHOPOTSO EA SLH RADIO LAOLI

1. Ho taolo ea seea-le-moea sa SLH, ka nako e le 'ngoe tobetsa o hatelle likonopo tsa P1 le P2.
2. LED ea taolo ea seea-le-moea e qala ho bonesa (bakeng sa metsotsoana e ka bang 10).
3. Lokolla li-push-button ka bobeli.
4. Tobetsa, bakeng sa motsotsoana o le 1, konopo ea push-up ho moamoheli (Fig.1 ref 8) e amanang le kanale eo u lakatsang ho e amahanya le taolo ea seea-le-moea.
5. LED e loketseng ho moamoheli (setšoantšo sa 1, ref. 7) e qala ho bonesa butle bakeng sa metsotsoana e mehlano.
6. Ka har'a metsotsoana ena e 5., Ha LED e laolang seea-le-moea e ntse e benya, tobetsa 'me u hatelle konopo e hlokahalang ea ho sututsa seea-le-moeeng (LED ea taolo ea seea-le-moea e khantša lebone le tsitsitseng).
7. Lebone la LED letlapeng (Fig.1 ref 7) le khantša ka holim'a sefate se tsitsitseng bakeng sa metsotsoana ea 1 ebe e ea OFF, e bontšang hore polokelo e phethiloe.
8. Lokolla konopo ea ho laola radio.
9. Tobetsa ka potlako habedi ka tatelano konopo ya memori e bolokilweng ya radio control.
   • Boto e tla romela taelo ho sehlahisoa se amanang le mocha.
10. Ho kenya li-control tse ling tsa seea-le-moea, fetisetsa khoutu ea konopo e bolokiloeng ka memori ea taolo ea seea-le-moea ho konopo e loketseng ea li-control tsa seea-le-moea tse lokelang ho eketsoa, ​​​​ho latela mokhoa o latelang:
    • a) Taolong ea seea-le-moea se bolokiloeng mohopolong, ka nako e le 'ngoe tobetsa le ho hatella li-push-buttons P1 le P2.
      b) LED ea taolo ea seea-le-moea e qala ho khantša.
      c) Lokolla li-push-button ka bobeli.
      d) Tobetsa konopo ea memori e bolokiloeng 'me u e hatelle (LED ea taolo ea seea-le-moea e khantša lebone le tsitsitseng).
    • e) Atamela li-control tsa seea-le-moea haufi, tobetsa 'me u hatelle konopo ea "radio control" hore e eketsoe, u e lokolle feela ka mor'a hore khanya e habeli ea LED e laolang seea-le-moea, e bontšang hore thuto e phethiloe.
    • Tobetsa ka potlako konopo e habeli ea memori e ncha e bolokiloeng taolong ea radio.
    • Boto e tla romela taelo ho sehlahisoa se amanang le mocha.

POLOKO EA KHOPOTSO EA LC RADIO LAOLI

Khoutu ea seea-le-moea ea LC e fumaneha feela bakeng sa limmaraka tse itseng mme feela bakeng sa moamoheli XR2 433C.

1. Tobetsa, bakeng sa motsotsoana o le 1, konopo ea push-up ho moamoheli (Fig.1 ref 8) e amanang le kanale eo u lakatsang ho e amahanya le taolo ea seea-le-moea.
2. LED e loketseng ho moamoheli (setšoantšo sa 1, ref. 7) e qala ho bonesa butle bakeng sa metsotsoana e mehlano.
3. Ka har'a metsotsoana ena e 5., Tobetsa konopo e loketseng ho LC remote control.
4. LED ho moamoheli (Fig.1, ref 7) e khantša lebone le tsitsitseng bakeng sa motsotsoana oa 1, e bontšang ho boloka mohopolo o phethiloe, ebe o tsoela pele ho khantša metsotsoana e meng ea 5, nakong eo taolo e 'ngoe ea seea-le-moea e ka bolokoang mohopolong.
5. Ha metsotsoana e 5. ha e se e fetile, LED ea tima, e bontšang qetello ea ts'ebetso.
6. Ho boloka lisebelisoa tse ling tsa radio, pheta mokhoa o fetileng.
   • Haeba u lakatsa ho tsoela pele ka mokhoa o hole, (ntle le ho bula setshelo sa moamoheli), latela mokhoa o ka tlase:
   • a) Nka taolo ea radio e seng e bolokile memoring.
   • b) Tobetsa 'me ka nako e le' ngoe u tšoare li-push-buttons P1 le P2 ho fihlela leseli le benyang la LED (Fig.1, ref 7) letlapeng la moamoheli le bonesa.
   • c) LED e tla benya butle ka metsotsoana e 5.
   • d) Ka har'a metsotsoana e 5. Tobetsa konopo ea "push-button" ea taolo ea seea-le-moea e neng e bolokiloe mohopolong ho nolofalletsa ho ithuta mocha o khethiloeng.
   • e) LED e holim'a boto e amanang le mocha o ithutoang e khanyetsa metsotsoana e 5., ka nako eo khoutu ea taolo e 'ngoe ea seea-le-moea e tlameha ho fetisoa.
   • f) LED (Fig.1 ref 7) e khantša holim'a sefate se tsitsitseng bakeng sa metsotsoana ea 2, e bontšang ho boloka mohopolo o phethiloe, ebe o tsoela pele ho khantša metsotsoana ea 5, nakong eo "e" e ka phetoang, hape le lintlha tse latelang, bakeng sa lisebelisoa tse ling tse hole 'me qetellong ea OFF.

TLHOKOMELO MOLAOLI TSOHLE TSA RADIO

1. Ho hlakola likhoutu TSOHLE tsa taolo ea seea-le-moea tse amanang le likanale 1 le 2, tšoara konopo ea SW1 kapa SW2 (Fig.1 ref 8) metsotsoana e 10.
2. LED (Setšoantšo sa 1, ref. 7) e amanang le ho totobetsoa ha konopo ea konopo bakeng sa metsotsoana e 5 ea pele, ebe e benya ka potlako bakeng sa metsotsoana e 5 e latelang.
3. Leseli la LED le khantša lebone le tsitsitseng ka metsotsoana e 2 ebe lea tima.
4. Lokolla konopo e tobelitsoeng ha li-LED tse amehang ka bobeli li khantša lebone le tsitsitseng.

MOSEBETSI MONA

• O ka laela dikanale tsa moamoheli ho tswa ho ditaolo tse fapaneng tsa radio. (Mohlala: taolo ea seea-le-moea 1 e laela kanale 1, taolo ea seea-le-moea 2 e laela kanale 2)

0470

• Mohlala: XR2 868C
• Maqhubu a Phetiso: 868.35MHz ±200KHz
• Phepelo ea motlakase: 12 ÷ 24 ac/dc
• Sehlahisoa sena se lumellana le Directive 99/05/EEC.
• Tšebeliso e khethehileng: sekoahelo sa heke.
• SEBELISA MAHALA A UE

0470

• Mohlala: XR2 433C
• Maqhubu a Phetiso: 433.92MHz ±100KHz
• Phepelo ea motlakase: 12 ÷ 24 ac/dc
• Sehlahisoa sena se lumellana le Directive 99/05/EEC.
• Tšebeliso e khethehileng: sekoahelo sa heke.
• SEBELISA MAHALA A UE.

TŠEBELETSO EA BAREKI

• Tlhaloso: FAAC SpA
• Ka Calari, 10
• 40069 Zola Predosa (BO) – ITALIA
• Mohala 003905161724
• Fekse. 0039051758518
• www.faac.it
• www.faacgroup.com

Lipotso Tse Botsoang Hangata

Ke likhoutu tse kae tse ka tšoaroang ka hlooho mocha ka mong?

U ka tšoara ka hlooho boholo ba likhoutu tse 250 tse arotsoeng lipakeng tsa likanale 1 le 2.

Mocheso oa ho sebetsa oa sehlahisoa ke ofe?

Mocheso oa ho sebetsa o tloha ho -20 ° C ho ea ho +55 ° C.

Litokomane / Lisebelisoa

FAAC XR2 433 C Boto ea Taolo ea Kantle ea Moamoheli oa Mecha [pdf] Buka ea Mong'a XR2 433 C, XR2 433 C Boto ea Taolo ea Kantle ea Baamoheli ba Mecha, Boto ea Taolo ea Baamoheli ba Kantle ea Mecha, Boto ea Taolo ea Baamoheli ba Kantle, Boto ea Taolo ea Moamoheli.

Litšupiso

• Bukana ea Mosebelisi