Digilog ESP32 Super Mini Dev Board
Litlhaloso
- Lebitso la Sehlahisoa: ESP32 Super Mini Dev Board
- Mofuta oa Boto: ESP32C3 Dev Module
- Puisano: USB CDC
- Lebelo la Baud: 9600
- Lebone la LED: GPIO8
Seta-1
My ESP32 Super Mini Dev Board (Setšoantšo sa 1) e amohela litšoantšo tse tsoang ho PC, empa ha e buisane le Serial Monitor (Bd = 9600) leha LED ea onBoard (ho GPIO8) e panya.
[setšoantšo|403×203](upload://pRi2u3tDsAxTivzokiEplEtzhlC.jpeg)
Setšoantšo-1
Seta-1
- Boto: "ESP32C3 Dev Module"
- USB CDC ho Boot: "E nolofalitsoe"
- Boema-kepe: "COM13 (ESP32S3 Dev Module)" // ha ho khetho e 'ngoe
Sketch
- hlalosa LED_BUILTIN 8
- char myData[10];
- void setup()
- Serial.qala(9600);
- pinMode(LED_BUILTIN, OUTPUT)
- void loop()
- digitalWrite(LED_BUILTIN, HIGH); // bulela LED (HIGH ke voltage level)
- tieho(1000); // emela motsotsoana
- digitalWrite(LED_BUILTIN, LOW); // tima LED ka ho etsa voltage LOW tieho (1000)
- byte n = Serial.available();
- haeba (n != 0) {byte m = Serial.readBytesUntil('\n', myData, sizeof (myData)-1); myData[m] = '\0'
- Serial.println(myData); }
- Serial.println(“Hello”); }
Seta se latelang se rarollotse bothata.
Seta-2
- Boto: "LOLIN C3 Mini"
- USB CDC ho Boot: "E nolofalitsoe"
- Boema-kepe: “COM13 (ESP32S3 Dev Module)”
- Bd = 9600
Sephetho
- Lumela
- Lumela
- Arduino // Ho tloha ho InputBox ea SM ho ea ho ESP32C3 ho ea ho OutputBox ea SM
- Lumela
- Lumela
Nka thabela ho utloa maikutlo a hau mabapi le - "LOLIN C3 ke eng".
- Se ke oa beha ESP32C3 Super Mini Board holim'a Breadboard ho qoba mathata a ho ikopanya.
- The onboard LED e hokahane ho DPin-8.
- Sebelisa jumper ea monna le mosali 'me u kopanye lehlakore la basali ho DPin-9 ho sebetsa joalo ka konopo ea kantle.
- Setšoantšo sa khokahano ea onFig. 1 LED le konopo li tšoana le setšoantšo sa 1.
- Khetha Boto ka tsela e latelang: IDE 2.3.1 –> Tools –> ESP32.
- LOLIN C3 Mini USB CDC On Boot: E nolofalitsoe.
- Kenya sekeche se fanoeng botong.
- Sheba hore na LED ea onboard e timme qalong.
- Ho koala switch ho tla etsa hore LED e ka holim'a sekepe e qale ho panya ka nako ea metsotsoana e 2.
- Netefatsa hore lebone la LED la onboard le butswe.f
- Tšoara ka bonolo lehlakore la monna la terata e leketlileng/seqhobane ka h G-pin ea Mini Board.
- Netefatsa hore LED e ka holim'a sekepe e benya ka nako ea metsotsoana e 2.
- Tobetsa konopo ea RST (Reset) ea Mini Board ebe o pheta ts'ebetso ha ho hlokahala.
Litokomane / Lisebelisoa
 |
Digilog ESP32 Super Mini Dev Board [pdf] Litaelo ESP32 Super Mini Dev Board, ESP32, Super Mini Dev Board, Mini Dev Board, Board |