contacta STS-K070 Window Intercom User System Guide

Sehlahisoa se Felletseview

Lisebelisoa tsa lifensetere tsa intercom li fana ka thuso bakeng sa puisano e hlakileng moo puo e tloaelehileng e senyehang ka ho sebelisa khalase, skrine ea tšireletso kapa litšitiso tse ling tse tšoanang.

Ho na le setsi sa boikhethelo sa loop, se fanang ka thuso e eketsehileng bakeng sa ba sebelisang lisebelisoa tsa ho utloa.

Likarolo tsa Sebui le Maekerofounu

1. Sebui Pod x 2
   
2. Microphone ea mouse x 2
   
3. Lipampitšana tsa ho lokisa tse Mahlakoreng a mabeli x 2
   

Kakaretso Likaroloana

1. Tlhophiso le Buka ea Mosebelisi
   
2. Ampmoqhobi
   
3. Moetapele oa IEC
   
4. Phepelo ea motlakase
   
5. Hearing Loop Aerial (boikhethelo)
   

Lokisa Kit:

• Adhesive Clip x 10
• No.6 x 1/2” Countersunk Screw x 15
• P-Clips x 6

Lihokelo

Ha o tlosa likhokahano tse tala bakeng sa ho fepa likhoele ka masoba, etsa bonnete ba hore tsohle li hloekisoa sebakeng se nepahetseng pele u hokela ampmoqhobi.

Ho kgothaletswa ho nka linepe e le rekoto pele o arola likhoele leha e le life. Sena ke ho netefatsa khokahano e nepahetseng; wiring e fosahetseng e ka ama tshebetso.

Litaelo tsa ho Hloma

Re khothaletsa hore ho kenngoe ho etsoe ke moenjiniere ea tšoanelehang, ea khomarelang litekanyetso tse amehang.

Sheba likahare tsa lebokose ho itloaetsa likaroloana.

Lisebelisoa tse khothalelitsoeng

Sesebelisoa sa mantlha se khothalelitsoeng ho kenya sistimi se tla kenyelletsa:

• Screwdrivers (Flat kapa Blade 2.5mm le Phillips Head PH2)
• Sesebelisoa sa Battery kapa Mains
• Li-drillbits: 2mm, 3mm, 5mm le 7mm
• Cable Tacking Gun (10mm)
• Li-cutters tsa terata / Strippers
• Tekanyo ea Tape
• Pensele kapa Pene ea Letšoao
• Lithae tsa Cable
• Ho hlahlathela

Fokotsa likhoele ha ho hlokahala (ntle le phepelo ea motlakase) ho bolelele bo hlokahalang ho hokela ka morao ho ampmolefi. Ha e na hoo e ka bang 6mm ea thapo e fella ho hokela ho li-plug tse peli tsa pin.

AmpHo kenya lifier

1. Beha sebaka ampho boloka thepa ka tlas'a khaontara ea basebetsi, ho etsa bonnete ba hore e ke ke ea sitisa basebetsi ha ba lutse.
2. Tšoaea lintlha tse 'nè tsa ho lokisa bakeng sa amplefilimi ka tlasa khaontara.
3. Koala le ho lokisa ampsetsiba sebakeng se sebedisoang ka dikurufu tse fanoeng.
4. Kenya le ampphepelo ea motlakase ea lifier e haufi le sokete ea motlakase e sebelisang borakete e kentsoeng le likurufu tsa ho lokisa.

Ho kenya Microphone & Sebui

1. Beha sebuela-hole lehlakoreng la moreki/moeti la k'haontareng, ho netefatsa hore ha e bake tšitiso.
2. Beha microphone ea mouse ka lehlakoreng la moreki / moeti oa counter top, ho etsa bonnete ba hore ha e bake tšitiso 'me e haufi le bareki / baeti ka hohle kamoo ho ka khonehang.
   
   Bakeng sa ts'ebetso e ntle ka ho fetisisa li-microphone tsohle tsa mouse li lokela ho kenngoa li shebane le mosebedisi joalokaha ho bontšoa setšoantšong se ka ho le letona. Bonyane sebaka se khothaletsoang lipakeng tsa li-microphone tsa mouse le li-pods tsa sebuela-pele ke 300mm.
3. Beha sebuela-hole lehlakoreng la basebetsi ba k'haontareng, ho netefatsa hore ha e bake tšitiso.
4. Beha microphone ea mouse ka lehlakoreng la basebetsi ba counter top, ho etsa bonnete ba hore ha e bake tšitiso 'me e haufi le basebetsi ka hohle kamoo ho ka khonehang.
5. Li-pods tsa libui li ka ba tsa boemo bo sa lefelloeng kapa tse tsitsitseng. E-ea mohatong oa 11 haeba u sa batle ho lokisa li-pods tsa sebui khaontareng.
   
6. Sebelisa masoba a tsamaiso ea lithapo k'haontareng ho tsamaisa likhoele tsa sebuela-pele le maekerofounu ea mouse ho ampmolefi. Haeba ho se ho se masoba a tsamaiso ea lithapo, phunya libaka tse loketseng haufi le ka morao ho basebetsi le mahlakoreng a moreki/moeti k'haontareng.
7. Ho na le mekhoa e 2 ea ho lokisa bakeng sa pod / staff pod. Lokisa li-pods holimo u sebelisa (a) letlapa le khomarelang le nang le mahlakore a mabeli kapa (b) li-screw tse fanoeng.
   a. Ho lokisa pod sebakeng u sebelisa sekhomaretsi sa mahlakoreng a mabeli:
   i. Tlosa lehlakore le le leng la liner 'me u khomarele sena ho setsi sa pod bohareng.
   ii. Tlosa mohala oa bobeli 'me u khomarele pod sebakeng seo u se batlang.
   b. Ho lokisa li-pods ho sebelisa li-screw:
   i. Sireletsa li-screw tsa x2 tsa countersunk sebakeng sa ho lokisa sebakeng se arohaneng sa 28mm.
   
   ii. Netefatsa hore hoo e ka bang 4mm ea hlooho ea screw e ka holim'a sebaka sa ho lokisa.
   
   Hlokomela: Beha li-screw ka liekele tsa 90 tse shebileng boemo ba motho eo u rerileng ho bo ema.
   iii. Beha pod ea hau holim'a lihlooho tsa screw, ho etsa bonnete ba hore li kena libakeng tsa ho lokisa tse sothehileng tse tlase ho yuniti:
   
8. Ho lokisa maekerofounu ea toeba sebakeng, sebelisa letlapa la ho lokisa le nang le mahlakore a mabeli kapa le phuphura ka lesoba la sekoti sekoping sa eona.
9. Fepa lithapo ka likoti tsa tsamaiso ea lithapo.
10. Qoba lithapo tse hlephileng kapa tse salang morao. Sebelisa trunking kapa ho thibela likotsi tsa maeto kapa li-unit tse huloang ho tloha moo li leng teng.
11. Tsamaisa li-cabling tsohle ka makhethe ho ea ho ampsebaka sa lifier ka lehlakoreng la basebetsi.

Ho Kenya Loop ea ho Utloa (Boikhethelo)

Aire e lokela ho ts'oaroa ka tlas'a deske-top kapa k'haontareng bohareng lehlakoreng la moreki kapa la moeti, halofo e 'ngoe e kenngoe ka mokhoa o tšekaletseng ka tlas'a khaontara' me halofo e 'ngoe e behoe ka ho otloloha, e shebane le moreki/moeti (joalo ka boemo ba pele bo ka tlase).

Beha moea tlas'a khaontara u sebelisa P-clips e fanoeng kapa mokhoa o mong oa ho lokisa oo u o khethileng. Sheba setšoantšo se ka tlase bakeng sa maemo a khothaletsoang.

A ke sebopeho se nepahetseng bakeng sa lupu ea kutlo ea khaontara.

B le C li amoheleha hafeela A e sa khonehe 'me moralo o matahantsoe e le hore matla a khoheli a lebisetsoe holimo ho hlooho ea mosebedisi.

Netefatsa hore matshwao ohle a loop ya kutlo a hlahisitswe ka ho hlaka.

AmpLifier Seta

Fetileview ea Likonopo tsa Panel e ka Pele

Tlhophiso

1. Hokela li-plug tsohle tse tala ka morao ho amplifier, ho latela libaka tse hatisitsoeng ka holimo ho li-sockets.
2. Matla ho amplifier ka ho tobetsa konopo ea On/Off.
3. Ha e tsamaisoa le ka mokhoa o tloaelehileng oa ts'ebetso ea amplifier e tla bonts'a Volume In LED 1 le Volume Out LED 1 e le botala bo tsitsitseng.
4. Ha the ampLifier e tingoe, molumo oohle oa khutsisoa 'me ha ho le e 'ngoe ea li-LED tse bonesitsoeng. Ho tobetsa konopo efe kapa efe ho tla retelehela ho amplifier hape.
5. Fetolela Bolumo ka hare le Bolumo ho tsoa boemong bo botle.
6. Tobetsa le ho tšoara likonopo tsa Volume In (+) kapa (-) ho eketsa kapa ho fokotsa boemo. Sebaka se lumellanang sa LED se tla bontša boemo ba molumo.
7. Netefatsa hore li-microphone tsa mouse li behiloe haufi le basebelisi ba tsona ka hohle kamoo ho ka khonehang.
8. Hlahloba amplifier e sebetsa ka botlalo ka ho netefatsa hore lebone le khubelu la 'fault' HA le hlahe ka pele.
9. The AmpLifier e se e thehiloe

Sistimi ea rona ea Window ea Intercom ampLifiers li se li setiloe esale pele ho maemo a molumo a loketseng basebelisi bohle. Haeba o hloka ho lokisa maemo a Maximum Volume, Ducking kapa Hearing Loop ka ntle ho sete e behiloeng esale pele ampli-parameter tsa lifier, sebelisa Mokhoa oa Moenjiniere.

Li-LED tsa Tlhahlobo ea Phoso

• Volume In LED 8 e tla lula e khubelu haeba ho na le phoso ka microphone ea basebetsi.
• Volume Out LED 8 e tla lula e le khubelu haeba ho na le phoso ka maekerofounu ea moreki/moeti.
• Volume In LED 8 e tla benya bofubelu haeba ho na le phoso ka loop (mohlala, aerial e robehileng).

Fektheri Default Settings

To return the amplifier ho li-setting tsa kamehla tsa feme:

1. Hlakola phepelo ea motlakase ebe u e hokela hape.
2. Lits'oants'o tsa LED li tla bonts'a mohlala oa leseli kholumong ea "Vol In". Sena se bontša ntlafatso ea firmware. Sena se tla lateloa ke lebone le letala ka tlase ho kholomo ka 'ngoe.
3. Ka metsotsoana e 20, tobetsa konopo ea On/Off le ea Volume In (-) hammoho, ebe u li lokolla.
4. Kholomo ea "Vol In" e tla boela e bonts'a ntlafatso ea firmware. Sena se bontša hore li-setting li tsosolositsoe.

Ho batle phoso

Letšoao	Phoso e ka etsahalang	Ketso
Ha ho na matla a fumanoeng ka ho amplifier ('me ho na le matla soketeng).	Motlakase ha o hoketsoe kapa o na le phoso. Fuse ea plug e butsoitse. Setsi sa phepelo ea motlakase se fosahetseng. Phoso ampmoqhobi.	Check power jack e hoketsoe ka thata. Fetola fuse. Haeba e foka hape, khutlisetsa yuniti ea phepelo ea motlakase. Fetola yuniti ea phepelo ea motlakase. Tlosa sebaka ampmoqhobi.
LED e khubelu e bonesitsoe holim'a phanele e ka pele.	LED e khubelu ea kamehla: Phoso ea maekerofounu ea basebetsi kapa moreki/moeti. LED e khubelu e hlaha ka mor'a puo: Phoso ea loop ea induction.	Netefatsa hore maekrofounu o hokeletsoe ka nepo le ka mokhoa o tiileng. Leka maekrofounu e 'ngoe ho netefatsa hore kou ea sebetsa. Netefatsa hore sehokelo sa induction loop se hoketsoe ka nepo ebile se hoketsoe ka thata.
Ha ke utloe molumo ka loop ea induction.	Induction loop kapa microphone ha e hoketsoe. Loop tester e na le phoso.	Sheba litaelo bakeng sa likhokahano tse nepahetseng, 'me, haeba ho khoneha, hlahloba sesebelisoa sa kutlo ka loop e tsebahalang e sebetsang. Netefatsa hore "loop tester" e na le sete e ncha ea libeteri.
Ke utloa ho kena-kenana \ ka libui (ho buzzing / mololi / mololi).	Thepa e sa sireletsoang kapa e sirelelitsoeng hampe e sebelisoa sebakeng se haufi. Bolumo ka hare bo behiloe holimo. Ho sebelisoa motlakase o fosahetseng.	Tima lisebelisoa life kapa life tsa mokha oa boraro ho tseba mohloli oa tšitiso. Access the ampLifier Engineer's Mode ho lokisa maemo a ka hare. Netefatsa hore yuniti ea rona ea phepelo ea motlakase e theiloeng fatše e hoketsoe.
Amplifier e kena maikutlong.	Bolumo bo ka hare bo behiloe holimo haholo. Maekerofounu o eme haufi haholo le sepikara.	Access the ampLifier Engineer's Mode ho lokisa maemo a ka hare. Tsamaisa maekrofounu sebakeng se hole le sebuela-hōle.
Yuniti ha e kene mokhoeng oa ho boloka matla.	Lerata la tikoloho le phahame haholo.	Tima litsamaiso life kapa life tsa moea, libapali tsa komporo le/kapa likhomphutha ho fokotsa lerata le teng.

Haeba ho se na ketso e atlehileng ka kopo, kopa thuso ho mofani oa hau kapa sehokelo sa Contacta.

Mokhoa oa Moenjiniere

Mokhoa oa Moenjiniere o u lumella ho fetola maemo a Volume In and Out, maemo a Ducking le maemo a Hearing Loop ho lumellana hantle le tikoloho ea hau le ho fihlela tšebetso e ntle ka ho fetisisa.

Pele o kena Mokhoa oa Moenjiniere, potoloha motlakase. Ho etsa sena kapa:

• Tlosa motlakase soketeng e kholo ebe o bula hape
• Tlosa sehokelo sa motlakase ebe o se kenya hape

Ho kenya Mokhoa oa Moenjiniere, ka nako e le 'ngoe tobetsa le ho lokolla likonopo tse latelang nakong ea metsotsoana e 20 ka mor'a ho palama motlakase:

• Konopo ea litlhophiso
• Konopo ea ho eketsa Volume In
• Konopo ea ho eketsa Volume Out

Nomoro ea 1 ea LED ho Volume In e tla benya botala ho bontša hore u Moeeng oa Moenjiniere.

Likonopo tsa ho bulela / ho tima le li-setting ho Mode oa Moenjiniere li sebetsa ka tsela e latelang:

Suthela sebakeng se latelang sa ho seta
Boloka 'me u tsoe ho Mokhoa oa Moenjiniere

The amplifier e tla tsoa ka bo eona Mokhoa oa Moenjineri haeba ho se na likonopo tse totobatsoang metsotso e 2.

Ho na le libaka tse 3 tse ka hlophisoang ho Moenjineri's Mode. U tla lula u kenya sebaka sa ho seta 1 pele. Thepa e tala ea Volume In LED e tla benya ho bontša hore na u sebakeng sefe sa ho seta.

Sebaka sa ho Hlophisa 1: Phetoho e Phahameng ea Bolumo (ho benya ha LED 1)

Sebaka sa Setupo sa 1 se u lumella ho fetola maemo a Volume In le Volume Out ho tsoela pele ho ntlafatsa sistimi bakeng sa tikoloho eo e kentsoeng ho eona.

1. Netefatsa hore litheko tsa bareki le basebetsi li theotsoe ka botlalo.
2. Fetola molumo oa basebetsi (Volume In) hore e be boemong bo botle. Tobetsa le ho tšoara likonopo tsa Volume In (+) kapa (-) ho eketsa kapa ho fokotsa boemo. Sebaka se lumellanang sa LED se tla bontša boemo ba molumo.
3. Eketsa molumo oa moreki (Volume Out) ho fihlela maikutlo a utloahala. Tobetsa le ho tšoara likonopo tsa Volume Out (+) kapa (-) ho eketsa kapa ho fokotsa boemo. Sebaka se lumellanang sa LED se tla bontša boemo ba molumo.
4. Fokotsa molumo oa moreki (Volume Out) ho fihlela maikutlo a felile.

Sebaka sa ho seta 2: Tokiso ea Ducking (LED 2 flashes)

Setupo Sebaka sa 2 se u lumella ho fetola boemo ba Ducking kapa ho e bulela / tima. Ts'ebetso ea ducking e fanoa ho fokotsa maikutlo ho sistimi ea intercom ea fensetere. Maikutlo a hlaha ha tlhophiso ea kakaretso ea litaolo tsa molumo ka bobeli e le holimo haholo. Sistimi ea ducking e sebetsa ka ho bona hore na ke maekrofono ofe moqoqong o sebelisoang, le ho fokotsa boemo ba molumo ka nakoana.

Sebaka sa ho seta sa 3: Phetoho ea ho Utloa ha Loop Drive (ho benya ha LED 3)

Setupo Sebaka sa 3 se u lumella ho fetola Hearing Loop Drive kapa ho e bulela/e tima.

Li-loops tsa ho utloa li ntlafatsa puisano ka ho nolofalletsa basebelisi ba lisebelisoa tsa kutlo ho utloa mehloli ea molumo ka kotloloho, ho fokotsa lerata le ka morao.

Maemo a koloi a lokela ho fetoloa e le hore LED 8 e khubelu e bonese ha feela ho na le litlhōrō tsa molumo oa puo.

Haeba e amplifier ha e na loop e khomaretsoeng, tima Hearing Loop Drive joalo ka ha ho bonts'itsoe setšoantšong se kaholimo.

Tšehetso ea Bareki

Contacta e na le leano la nts'etsopele ea lihlahisoa tse tsoelang pele, 'me ka hona liphetoho tse nyenyane tsa litlhaloso li ka' na tsa se ke tsa bonahala bukeng ena. Litšoantšo, lileibole, sephutheloana, lisebelisoa le mebala ea lihlahisoa li ka fetoha ntle le tsebiso.

Lintlha tse ling li fumaneha ho rona websebaka le mocha oa rona oa YouTube.

Fensetere Intercom STS-A31H AmpLifier Seta Video

Window Intercom Unboxing & Positioning Guide Video

www.contacta.co.uk
sales@contacta.co.uk
+44 (0) 1732 223900
Tšehetso ea Theknoloji - Ext 5

Litokomane / Lisebelisoa

Contacta STS-K070 Window Intercom System [pdf] Bukana ea Mosebelisi STS-K070 Window Intercom System, STS-K070, Window Intercom System, Intercom System, System

Litšupiso

• Bukana ea Mosebelisi