Boardcon E Kenyellelitsoeng CM1126B-P Sistimi ho Mojule
Litlhaloso
| Sebopeho | Litlhaloso |
| CPU | Quad-core Cortex-A53 |
| DDR | 2GB LPDDR4 (ho fihla ho 4GB) |
| eMMC LEHLANYA | 8GB (ho fihla ho 256GB) |
| Matla | DC 3.3V |
| MIPI DSI | 4-Lane |
| I2S | EA-4-CH |
| MIPI CSI | 2-CH 4-Lane |
| RGB LCD | 24 bit |
| Khamera | 1-CH(DVP) le 2-CH(CSI) |
| USB | 2-CH (USB HOST 2.0 le OTG 2.0) |
| Ethernet | 1000M GMAC |
| SDMMC | EA-2-CH |
| I2C | EA-5-CH |
| SPI | EA-2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | EA-11-CH |
| ADC IN | EA-4-CH |
| Boto Dimension | 34 x 35 limilimithara |
Selelekela
Mabapi le Bukana ena
Bukana ena e reretsoe ho fa mosebedisi ho fetaview ea boto le melemo ea eona, lintlha tse felletseng tsa likarolo, le mekhoa ea ho seta. E na le boitsebiso ba bohlokoa ba tšireletso hape.
Maikutlo le Nchafatso ea Bukana ena
Ho thusa bareki ba rona ho sebelisa lihlahisoa tsa rona hamolemo, re lula re etsa hore lisebelisoa tse ling tse nchafalitsoeng li fumanehe ho Boardcon websaete (www.boardcon.com, www.armdesigner.com). Tsena li kenyelletsa libuka, lintlha tsa kopo, mohlala oa lenaneoamples, le software e ntlafalitsoeng le hardware. Kena nako le nako ho bona tse ncha! Ha re beha mosebetsi pele ho lisebelisoa tsena tse nchafalitsoeng, maikutlo a tsoang ho bareki ke tšusumetso ea pele, Haeba u na le lipotso, maikutlo, kapa matšoenyeho ka sehlahisoa kapa morero oa hau, ka kopo u se ke ua tsilatsila ho ikopanya le rona ho support@armdesigner.com.
Setšoantšo sa CM1126B-P
Kakaretso
CM1126B-P system-on-module e na le Rockchip's RV1126B-P, e hahiloeng ka quad-core Cortex-A53, 3.0 TOPs NPU, le RISC-V MCU. E etselitsoe ka ho khetheha lisebelisoa tsa IPC/CVR, lisebelisoa tsa AI Camera, lisebelisoa tse bohlale tse sebetsanang le liroboto tse nyane. Litharollo tse sebetsang hantle haholo le tse nang le matla a tlase li ka thusa bareki ho hlahisa theknoloji e ncha kapele le ho ntlafatsa katleho ea tharollo. Boholo bo bonyenyane bo ka beoa holim'a 38board. Kamora ntlafatso ea lisebelisoa ho tloha CM1126 (V1) ho ea CM1126B-P (V2), moo SoC e nchafatsoang ho RV1126B-P, matšoao a Reset & OTG_VBUS le GPIO vol ea module ea WIFI/BT.tage tlameha ho sebetsa boemong ba 3.3V logic.
Likaroloana
Microprocessor
- Quad-core Cortex-A53 ho fihla ho 1.6GHz
- 32KB I-cache le 32KB D-cache bakeng sa konokono ka 'ngoe, 512KB L3 cache
- 3.0 TOPS Neural Process Unit
- RISC-V MCU ho tšehetsa 250ms boot boot
- Boholo ba 12M ISP
Memori Mokhatlo
- LPDDR4 RAM ho fihla ho 4GB
- eMMC ho fihla ho 256GB
- SPI Flash ho fihla ho 8MB
Setsi sa video / Encoder
- E ts'ehetsa li-decode / encode ho fihla ho 4K@30fps
- E ts'ehetsa ho hlakisoa ha nako ea nnete ea H.264/265
- E ts'ehetsa khouto ea video ea UHD H.264/265 ea nako ea nnete
- Boholo ba setšoantšo bo fihla ho 8192 × 8192
Hlahisa Subsystem
- Sephetho sa Video
- E tšehetsa litsela tse 4 tsa MPI DSI ho fihla ho 2560 × 1440@60fps
- E tšehetsa tlhahiso e tšoanang ea 24-bit RGB
- Setšoantšo ka
- E ts'ehetsa ho fihla ho 16-bit DVP interface
- E tšehetsa 2ch MIPI CSI 4lanes interface
I2S/PCM/ AC97
- Khokahano e meraro ea I2S/PCM
- Tšehetsa Mic array Ho fihlela ho 8ch PDM/TDM interface
- Ts'ehetsa tlhahiso ea molumo oa PWM
USB le PCIE
- Li-interface tse peli tsa 2.0 USB
- USB 2.0 OTG e le 'ngoe le moamoheli a le mong oa 2.0 USB
Ethernet
- RTL8211F ka sekepe
- Tšehetsa 10/100/1000M
I2C
- Ho fihlela ho li-I2C tse hlano
- Mokhoa o tloaelehileng oa ts'ehetso le mokhoa o potlakileng (ho fihla ho 400kbit / s)
SDIO
- Ts'ehetsa protocol ea 2CH SDIO 3.0
SPI
- Ho fihla ho balaoli ba SPI ba babeli,
- Full-duplex synchronous serial interface
UART
- Tšehetsa ho fihla ho 6 UARTs
- UART2 e nang le lithapo tse 2 bakeng sa lisebelisoa tsa ho lokisa bothata
- E kenyelelitsoe li-FIFO tse peli tsa 664-byte
- Ts'ehetsa mokhoa oa ho laola phallo ea koloi bakeng sa UART0/1/3/4/5
ADC
- Ho fihla ho likanale tse 'ne tsa ADC
- Qeto ea 12-bit
- MoqtagE kenya letsoho pakeng tsa 0V le 1.8V
- Tšehetsa ho fihla ho 1MS/ssampsekhahla sa ling
PWM
- Li-PWM tse 11 tsa on-chip tse nang le ts'ebetso e thehiloeng ho tšitiso
- Ts'ehetso ea 32-bit time/counter facility
- Khetho ea IR ho PWM3/7
Sehlopha sa matla
- Discrete Power ka sekepeng
- Kenyeletso e le 'ngoe ea 3.3V
Setšoantšo sa CM1126B-P Block
Setšoantšo sa RV1126B-P Block
Boto ea nts'etsopele (Idea1126) Block Diagram
Boemo ba CM1126B-P PCB
Tlhaloso: CM1126B-P Pin
| Pin | Letshwao | Tlhaloso kapa mesebetsi | Lethathamo la GPIO | Moqtage |
| 1 | LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Fatše | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Bakeng sa debug | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Bakeng sa debug | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Pin | Letshwao | Tlhaloso kapa mesebetsi | Lethathamo la GPIO | Moqtage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Fatše | 0V | |
| 32 | OTG_DP | E ka sebelisoa ho jarolla | 1.8V | |
| 33 | OTG_DM | E ka sebelisoa ho jarolla | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Kenyeletso ea Matla a Maholo | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Kenyeletso ea Matla a Maholo | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | E tlameha ho sebelisoa bakeng sa karete ea SD | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | Tlhahiso ea oache ea RTC | GPIO0_A2_u | 3.3V(V2) |
| 42 | NRETSENG | Seta hape senotlolo | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V |
| Pin | Letshwao | Tlhaloso kapa mesebetsi | Lethathamo la GPIO | Moqtage |
| 52 | MIPI_CSI_RX0_D0
N |
Kenyeletso ea MIPI CSI0 kapa LVDS0 | 1.8V | |
| 53 | GND | Fatše | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
Kenyeletso ea MIPI CSI1 kapa LVDS1 | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Fatše | 0V | |
| 71 | LED1/CFG_LDO0 | Ethernet LINK LED | 3.3V | |
| 72 | LED2/CFG_LDO1 | Ethernet SPEED LED | 3.3V | |
| 73 | MDI0 + | Letšoao la Ethernet MDI | 1.8V | |
| 74 | MDI0- | Letšoao la Ethernet MDI | 1.8V | |
| 75 | MDI1 + | Letšoao la Ethernet MDI | 1.8V | |
| 76 | MDI1- | Letšoao la Ethernet MDI | 1.8V | |
| 77 | MDI2 + | Letšoao la Ethernet MDI | 1.8V | |
| 78 | MDI2- | Letšoao la Ethernet MDI | 1.8V | |
| 79 | MDI3 + | Letšoao la Ethernet MDI | 1.8V | |
| 80 | MDI3- | Letšoao la Ethernet MDI | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Pin | Letshwao | Tlhaloso kapa mesebetsi | Lethathamo la GPIO | Moqtage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Fatše | 0V | |
| 91 | LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | Tlatsetso ea ADC | 1.8V | |
| 114 | ADCIN2 | Tlatsetso ea ADC | 1.8V | |
| 115 | ADCIN1 | Tlatsetso ea ADC | 1.8V | |
| 116 | ADKEY_IN0 | Mokhoa oa ho hlaphoheloa (10K PU) | 1.8V | |
| 117 | GND | Fatše | 0V | |
| 118 | SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Pin | Letshwao | Tlhaloso kapa mesebetsi | Lethathamo la GPIO | Moqtage |
| 120 | SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Hlokomela:
1. Boholo ba GPIO voltage ke 1.8V, empa lithakhisa tse ling li tšoailoe 3.3V. 2. GPIO voltage fetola ho 3.3V bakeng sa tšoauoa (V2). |
||||
Nts'etsopele (Idea1126)
Tataiso ea Moralo oa Hardware
Peripheral Circuit Reference
Potoloho ea Matla a Maholo
Debug Circuit
USB OTG Interface Circuit
PCB Footprint
Litšobotsi tsa Motlakase oa Sehlahisoa
Ho senya le Mocheso
| Letšoao | Paramethara | Min | Tlanya | Max | Yuniti |
| VCC3V3_SYS | Sistimi ea IO
Moqtage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Isys_in | Kenyelletso ea VCC3V3_SYS Hona joale | 850 | mA | ||
| Ta | Mocheso oa ho sebetsa | -20 | 70 | °C | |
| Tstg | Mocheso oa polokelo | -40 | 85 | °C |
Botšepehi ba Teko
| Teko ea Ts'ebetso ea Mocheso o Phahameng | ||
| Litaba | Ho sebetsa 8h ka mocheso o phahameng | 55 ° C ± 2 ° C |
| Sephetho | TBD |
| Teko ea Bophelo ea Ts'ebetso | ||
| Litaba | Ho sebetsa ka kamoreng | 120h |
| Sephetho | TBD |
Tiisetso e Lekanyelitsoeng
Boardcon e fana ka tumello ea hore sehlahisoa sena se hloke bofokoli linthong tse bonahalang le moetsong oa selemo ho tloha ka letsatsi la theko. Nakong ena ea tiisetso, Boardcon e tla lokisa kapa e nkele yuniti e nang le bothata ka mokhoa o latelang: Khopi ea invoice ea mantlha e tlameha ho kenyeletsoa ha e khutlisetsa unit e nang le bothata ho Boardcon. Tiisetso ena e lekanyelitsoeng ha e koahele litšenyehelo tse bakiloeng ke lehalima kapa ts'ebetso e 'ngoe ea motlakase, tšebeliso e mpe, tlhekefetso, maemo a sa tloaelehang a ts'ebetso, kapa liteko tsa ho fetola kapa ho fetola tšebetso ea sehlahisoa. Tiisetso ena e lekanyelitsoe ho lokisa kapa ho nkela sebaka se senyehileng. Ha ho ketsahalo e tla ba le boikarabello kapa boikarabello bakeng sa tahlehelo kapa ts'enyehelo efe kapa efe, ho kenyeletsoa empa e sa lekanyetsoe ho phaello efe kapa efe e lahlehileng, ts'enyehelo ea tšohanyetso kapa ea litlamorao, tahlehelo ea khoebo, kapa phaello e lebelletsoeng e bakoang ke ts'ebeliso kapa ho se khone ho sebelisa sehlahisoa sena. Litokiso tse entsoeng ka mor'a ho fela ha nako ea tiisetso li itšetlehile ka tefiso ea tokiso le litšenyehelo tsa ho khutlisa thepa. Ka kopo ikopanye le Boardcon ho hlophisa litšebeletso life kapa life tsa tokiso le ho fumana leseli la tefiso ea tokiso.
FAQs
Q: Nka ntlafatsa memori ea DDR joang ho CM1126B-P?
A: CM1126B-P e tšehetsa mohopolo oa ho fihla ho 4GB LPDDR4. Ho ntlafatsa, etsa bonnete ba ho lumellana le litlhaloso le ho latela mekhoa e khothaletsoang.
Q: Tlhokahalo ea phepelo ea motlakase bakeng sa CM1126B-P ke efe?
A: Tlhokahalo ea matla bakeng sa CM1126B-P ke DC 3.3V. Netefatsa hore ho fana ka motlakase o tsitsitseng ka har'a sebaka sena bakeng sa ts'ebetso e nepahetseng.
P: A na nka eketsa matla a polokelo ea eMMC ho CM1126B-P?
A: E, polokelo ea eMMC ho CM1126B-P e ka atolosoa ho fihla ho 256GB. Netefatsa hore e tsamaellana le lisebelisoa tsa polokelo tse tšehetsoeng pele u ntlafatsa.
Litokomane / Lisebelisoa
 |
Boardcon E Kenyellelitsoeng CM1126B-P Sistimi ho Mojule [pdf] Bukana ea Mosebelisi V2.20250422, CM1126B-P Sistimi ho Mojule, CM1126B-P, Sistimi ho Mojule, Mojule |