Autonics TCD210240AC Lilaoli tsa Mocheso ka nako e le 'ngoe le Mohatsela oa PID
Tlhahisoleseding ya Sehlahiswa
The TK Series Simultaneous Heating & Cooling Output PID Temperature Controllers ke lisebelisoa tse sebelisetsoang ho laola mocheso lits'ebetsong tse fapaneng tse kenyeletsang mechine, lisebelisoa tsa bongaka, lisebelisoa tsa tšireletso, le tse ling. Balaoli ba na le lisebelisoa tse sa sireletsehang tse kentsoeng ho thibela kotsi e tebileng kapa tahlehelo ea moruo. Li etselitsoe ho sebetsa libakeng tse ka hare ho sebaka se ka holimo ho 2,000m le tekanyo ea tšilafalo ea 2. Balaoli ba na le mekhoa e sa tšoaneng ea ho laela bakeng sa lisebelisoa / lihlahisoa, ts'ebetso le matla a matla. Ba na le tlhahiso ea taolo e ka ba relay, SSR drive, kapa selectable current kapa SSR drive. Sehlahisoa ha sea lokela ho sebelisoa libakeng tseo ho nang le khase e tukang, e phatlohileng/e senyang, mongobo o phahameng, mahlaseli a letsatsi, mocheso o khanyang, ho thothomela, tšusumetso, kapa letsoai.
Litaelo tsa Tšebeliso ea Sehlahisoa
- Kenya selaoli holim'a phanele ea sesebelisoa sebakeng se ka tlung se bophahamo ba ho fihla ho 2,000m le tekanyo ea tšilafalo ea 2.
- Netefatsa hore lisebelisoa tse sa sireletsehang li kentsoe ha u sebelisa molaoli o nang le mochini o ka bakang kotsi e mpe kapa tahlehelo e kholo ea moruo.
- Sebelisa thapo ea AWG 20 (0.50 mm2) kapa ho feta ha o hokela tlhahiso ea matla le tlhahiso ea relay. Sebelisa thapo ea AWG 28 ho isa ho 16 ha o hokela thapo ea sensor le thapo ea puisano ntle le thapo e inehetseng.
- Tiisa likurufu tsa theminale ka torque e tiisang ea 0.74 ho isa ho 0.90 N m ha o hokela likhoele.
- Sheba likhokahano pele u kenya likhoele ho thibela mollo.
- Sebelisa molaoli ka har'a lintlha tse reriloeng ho qoba tšenyo ea mollo kapa sehlahisoa.
- Hloekisa selaoli ka lesela le omeletseng 'me u qobe ho sebelisa metsi kapa motsoako oa tlhaho ho thibela mollo kapa ts'ebetso ea motlakase.
- Beha sehlahiswa hole le chip, lerole le masalla a terata tse phallang ho yuniti e ka bakang tshenyo ya mollo kapa sehlahiswa.
- Se ke oa qhaqha kapa oa fetola selaoli ho thibela mollo kapa ts'ebetso ea motlakase.
Selelekela
Rea leboha ka ho khetha sehlahisoa sa rona sa Autonics. Bala 'me u utloisise bukana ea litaelo le tataiso ka botlalo pele u sebelisa sehlahisoa. Bakeng sa polokeho ea hau, bala 'me u latele lintlha tse ka tlase tsa polokeho pele u li sebelisa. Bakeng sa polokeho ea hau, bala 'me u latele lintlha tse ngotsoeng bukeng ea litaelo, libuka tse ling le Autonics websebaka. Boloka bukana ena ea litaelo sebakeng seo u ka se fumanang habonolo. Litlhaloso, litekanyo, joalo-joalo li ka fetoha ntle le tsebiso bakeng sa ntlafatso ea sehlahisoa Meetso e meng e ka emisoa ntle le tsebiso. Latela Autonics websaete bakeng sa tlhaiso-leseling ea morao-rao.
Mehopolo ea Tšireletseho
- Ela hloko 'Lintlha tsa Tšireletso' bakeng sa ts'ebetso e sireletsehileng le e nepahetseng ho qoba likotsi.
- letšoao le bontša tlhokomeliso ka lebaka la maemo a khethehileng ao likotsi li ka hlahang ho ona.
Tlhokomediso Ho hloleha ho latela litaelo ho ka baka kotsi e mpe kapa lefu
- Sesebediswa se sa sireletsehang se tlameha ho kenngwa ha o sebedisa yuniti e nang le metjhini e ka bakang kotsi e kgolo kapa tahlehelo e kgolo ya moruo.(mohlala, taolo ya matla a nyutlelie, thepa ya bongaka, dikepe, makoloi, diporo, difofane, disebediswa tse tukang, disebediswa tsa polokeho, thibelo ya botlokotsebe/dikoduwa. lisebelisoa, joalo-joalo) Ho hloleha ho latela taelo ena ho ka baka kotsi ea botho, tahlehelo ea moruo kapa mollo.
- Se ke oa sebelisa yuniti sebakeng seo ho nang le khase e tukang, e phatlohang/e senyang, mongobo o phahameng, mahlaseli a letsatsi, mocheso o khanyang, thothomelo, tšusumetso kapa letsoai. Ho hloleha ho latela taelo ena ho ka baka ho phatloha kapa mollo.
- Kenya ho phanele ea sesebelisoa ho e sebelisa. Ho hloleha ho latela taelo ena ho ka baka ts'oaetso ea motlakase.
- Se ke oa hokela, ho lokisa, kapa ho hlahloba yuniti ha o ntse o hoketsoe mohloling oa motlakase. Ho hloleha ho latela taelo ena ho ka baka mollo kapa ts'okelo ea motlakase.
- Sheba 'Likhokahanyo' pele u kopanya. Ho hloleha ho latela taelo ena ho ka baka mollo.
- Se ke oa qhaqha kapa oa fetola yuniti. Ho hloleha ho latela taelo ena ho ka baka mollo kapa ts'okelo ea motlakase.
Tlhokomeliso Ho hloleha ho latela litaelo ho ka baka kotsi kapa tšenyo ea sehlahisoa
- Ha o hokela tlhahiso ea matla le tlhahiso ea relay, sebelisa thapo ea AWG 20 (0.50 mm2) kapa ho feta, 'me u tiise screw ea theminale ka torque e tiisang ea 0.74 ho isa ho 0.90 N m. Ha o hokela thapo ya sensara le thapo ya puisano ntle le thapo e inehetseng, sebedisa thapo ya AWG 28 ho isa ho 16 mme o tiise sekurufu sa terminal ka torque e tiisang ya 0.74 ho isa ho 0.90 N m. Ho hloleha ho latela taelo ena ho ka baka mollo kapa ho se sebetse hantle ka lebaka la ho hloleha ho kopana.
- Sebelisa yuniti ka har'a lintlha tse reriloeng. Ho hloleha ho latela taelo ena ho ka baka tšenyo ea mollo kapa sehlahisoa
- Sebelisa lesela le omeletseng ho hloekisa yuniti, 'me u se ke ua sebelisa metsi kapa motsoako oa tlhaho. Ho hloleha ho latela taelo ena ho ka baka mollo kapa ts'okelo ea motlakase.
- Beha sehlahiswa hole le chip, lerole, le masalla a terata a kenang yuniti. Ho hloleha ho latela taelo ena ho ka baka tšenyo ea mollo kapa sehlahisoa.
Litemoso nakong ea Tšebeliso
- Latela litaelo ho 'Litemoso nakong ea Tšebeliso'. Ho seng joalo, e ka baka likotsi tse sa lebelloang.
- Sheba polarity ea li-terminals pele u kenya sensara mocheso. Bakeng sa sensor ea mocheso oa RTD, e kenye terata joalo ka mofuta oa terata e 3, o sebelisa likhoele ka botenya le bolelele bo lekanang. Bakeng sa sensor ea mocheso oa thermocouple (TC), sebelisa terata e behiloeng bakeng sa ho atolosa mohala.
- Boloka hole le molumo o phahamengtaglithapo tsa e kapa lithapo tsa motlakase ho thibela lerata le kenang. Haeba u kenya mohala oa motlakase le mohala oa lets'oao haufi-ufi, sebelisa sefahla sa mohala kapa varistor mothapong oa motlakase le terata e sirelelitsoeng moleng oa lets'oao la ho kenya. Se ke oa sebelisa haufi le sesebelisoa se hlahisang matla a matla a makenete kapa lerata le phahameng la maqhubu.
- Se ke oa sebelisa matla a fetelletseng ha o hokela kapa o hakolla lihokelo tsa sehlahisoa.
- Kenya sesebelisoa sa motlakase kapa sekhechana sa potoloho sebakeng se fumanehang habonolo bakeng sa ho fana kapa ho hakolla motlakase.
- Se ke oa sebelisa yuniti molemong o mong (mohlala, voltmeter, ammeter), empa mocheso
molaoli. - Ha u fetola sensor ea ho kenya, tima motlakase pele u fetoha. Ka mor'a ho fetoha
sensor ea ho kenya, fetola boleng ba parameter e lumellanang. - 24 VAC,
24-48 VDC
phepelo ea motlakase e lokela ho ba insulated le matla a fokolangtage/hona joale kapa Sehlopha sa 2, SELV sesebelisoa sa phepelo ea motlakase. - Se ke oa feta mohala oa puisano le mohala oa motlakase. Sebelisa terata e sothehileng bakeng sa mohala oa puisano 'me u hokele sefaha sa ferrite pheletsong e' ngoe le e 'ngoe ea mohala ho fokotsa phello ea lerata le kantle.
- Etsa sebaka se hlokehang ho potoloha yuniti bakeng sa mahlaseli a mocheso. Bakeng sa litekanyo tse nepahetseng tsa mocheso, futhumatsa sesebelisoa ho feta metsotso e 20 kamora ho bulela motlakase.
- Etsa bonnete ba hore phepelo ea motlakase voltage fihla ho vol e lekantsoengtage kamora metsotsoana e 2 kamora ho fana ka matla.
- Se ke oa ts'oara terata ho li-terminals tse sa sebelisoang.
- Sehlopha sena se ka sebelisoa maemong a latelang.
- Ka tlung (boemong ba tikoloho e kentsoe 'Specifications')
- Altitude Max. 2,000 m
- Tekanyo ea tšilafalo 2
- Sehlopha sa ho kenya II
Ho Odara Boitsebiso
Sena ke sa litšupiso feela, sehlahisoa sa 'nete ha se tšehetse metsoako eohle. Bakeng sa ho khetha mofuta o boletsoeng, latela Autonics websebaka.
Boholo
- N: DIN W 48 × H 24 limilimithara
- SP: DIN W 48 × H 48 limilimithara (mofuta oa plug oa 11)
- S: DIN W 48 × H 48 limilimithara
- M: DIN W 72 × H 72 limilimithara
- W: DIN W 96 × H 48 limilimithara
- H: DIN W 48 × H 96 limilimithara
- L: DIN W 96 × H 96 limilimithara
Khetho ho kena/ho tsoa
| Size: N | ||
| PN | KHAOLO2 | Mosebetsi |
| 1 | Mofuta o tloaelehileng 01) | Kenyeletso ea Alarm 1 + CT |
| Ho futhumatsa le ho futhumatsa | Alamo 2 | |
| 2 | Mofuta o tloaelehileng | Alamo 1 + Alamo 2 |
| D | Mofuta o tloaelehileng | Alamo 1 + Kenyelletso ea dijithale 1/2 |
| Ho futhumatsa le ho futhumatsa | Kenyelletso ea dijithale 1/2 | |
|
R |
Mofuta o tloaelehileng | Alamo 1+ Phetiso
tlhahiso |
| Ho futhumatsa le ho futhumatsa | Phetiso ea phetiso | |
|
T |
Mofuta o tloaelehileng | Phallo ea alamo 1 + RS485
puisano |
| Ho futhumatsa le ho futhumatsa | RS485 puisano | |
Boholo: Mosebetsi oa SP PN 1 Alamo 1
| Boholo: S, M, W, H, L | |
| PN | Mosebetsi |
| 1 | Alamo 1 |
| 2 | Alamo 1 + Alamo e hlahisoang 2 |
| R | Alarm 1 + Phetiso ea phetiso |
| T | Alarm 1 + RS485 puisano |
| A | Alamo 1 + Alamo 2 + Phatlalatso ea phetiso |
| B | Alarm 1 + Alarm 2 + RS485 puisano |
| D | Alamo 1 + Alamo 2 + Kenyelletso ea dijithale 1/2 02) |
- Mokhoa oa ho kenya CT oa TK4N o ka khethoa feela ka mokhoa o tloaelehileng oa mofuta o nang le alamo ea 1. (ntle le TK4SP)
- Ke feela bakeng sa TK4S-D, terminal ea OUT2 e sebelisoa e le terminal ea DI-2 ea ho kenya.
- Ha mokhoa oa ho sebetsa e le taolo ea ho futhumatsa kapa ea ho pholisa, OUT2 e ka sebelisoa e le tlhahiso ea alamo 3 (ntle le TK4N).
- Ha mokhoa oa ho sebetsa e le taolo ea ho futhumatsa kapa ea ho pholisa, OUT2 e ka sebelisoa e le phetisetso ea 2.
Rekiswa ka thoko
- 11 Pin sokete: PG-11, PS-11 (N)
- Transformer ea hajoale (CT)
- Sekoahelo sa tšireletso ea terminal: RSA / RMA / RHA / RLA Cover
- Puisano converter: SCM Series
Litlhaloso
| Letoto | TK4N | TK4SP | TK4S | TK4M | |
| Matla
phepelo |
Mofuta oa AC | 100 - 240 VAC 50/60 Hz ±10% | |||
| Mofuta oa AC/DC | – | 24 VAC 50/60 Hz ±10%, 24-48 VDC ±10% | |||
| Matla
tshebediso |
Mofuta oa AC | ≤ 6 VA | ≤ 8 VA | ||
| Mofuta oa AC/DC | – | AC: ≤ 8 VA, DC ≤ 5W | |||
| Boima ba yuniti (e phuthetsoe) | ≈ 70 g
(≈ 140 g) |
≈ 85 g
(≈ 130 g) |
≈ 105 g
(≈ 150 g) |
≈ 140 g
(≈ 210 g) |
|
| Letoto | TK4W | TK4H | TK4L | |
| Matla
phepelo |
Mofuta oa AC | 100 - 240 VAC 50/60 Hz ±10% | ||
| Mofuta oa AC/DC | 24 VAC 50/60 Hz ±10%, 24-48 VDC ±10% | |||
| Matla
tshebediso |
Mofuta oa AC | ≤ 8 VA | ||
| Mofuta oa AC/DC | AC: ≤ 8 VA, DC ≤ 5W | |||
| Boima ba yuniti (e phuthetsoe) | ≈ 141 g (≈ 211 g) | ≈ 141 g (≈ 211 g) | ≈ 198 g (≈ 294 g) | |
| Sampnako ea ling | 50 ms | |
| Lintlha tse kentsoeng | Sheba 'Mofuta oa Input le Using Range' | |
|
Khetho ea ho kenya |
CT input |
• 0.0-50.0 A (lefapha la litekanyo tsa mantlha tsa hajoale)
• CT karo-karolelano: 1/1,000 • Ho nepahala ha tekanyo: ±5% FS ±1digit |
|
Kenyelletso ea dijithale |
• Khokahano – HO BUTSE: ≤ 2 kΩ, TIMA: ≥ 90 kΩ
• Ho se kopane – residual voltage ≤ 1.0 V, ho lutla hona joale ≤ 0.1 mA • Ho tsoa hona joale: ≈ 0.5 mA ka ho kenya letsoho |
|
| Laola tlhahiso | Relay | 250 VAC 3 A, 30 VDC 3 A 1a |
| SSR | 11 VDC ± 2 V, ≤ 20 mA | |
| Hona joale | DC 4-20 mA kapa DC 0-20 mA (parameter), ho hanyetsa mojaro: ≤ 500 Ω | |
| Alamo
tlhahiso |
Relay | AL1, AL2: 250 VAC 3 A 1a
• TK4N AL2: 250 VAC 0.5 A 1a (≤ 125 VA) |
| Khetho ea khetho | Phetiso | DC 4 - 20 mA (Ho hanyetsa moroalo: ≤ 500 Ω, ho nepahala ha tlhahiso: ± 0.3%
FS) |
| RS485 comm. | Modbus RTU | |
| Mofuta oa ponts'o | Karolo ea 7 (e khubelu, e tala, e mosehla), mofuta oa LED | |
| Mofuta oa taolo | Ho futhumatsa, ho pholisa |
ON/OFF, P, PI, PD, PID Control |
| Ho futhumatsa le
Ho phodisa |
||
| Hysteresis | • Thermocouple, RTD: 1 ho 100 (0.1 ho 100.0) ℃/℉
• Analoge: 1 ho isa ho 100 dijiti |
|
| Sehlopha se lekanang (P) | 0.1 ho isa ho 999.9 ℃/℉ (0.1 ho isa ho 999.9%) | |
| Nako ea bohlokoa (I) | 0 ho isa ho 9,999 sec | |
| Nako ea tlhahiso (D) | 0 ho isa ho 9,999 sec | |
| Control cycle (T) | • Relay e hlahisoang, tlhahiso ea koloi ea SSR: 0.1 ho 120.0 sec
• Kgetho ya hona jwale kapa SSR drive tlhahiso: 1.0 ho 120.0 sec |
|
| Seta bocha ka letsoho | 0.0 ho isa ho 100.0% | |
| Relay bophelo potoloho |
Mechini |
OUT1/2: ≥ 5,000,000 ts'ebetso
AL1/2: ≥ 20,000,000 ts'ebetso (TK4H/W/L: ≥ 5,000,000 ts'ebetso) |
| Motlakase | ≥ 100,000 ts'ebetso | |
| Matla a dielectric | E itšetlehile ka phepelo ea motlakase | |
| AC voltagmofuta | Pakeng tsa karolo ea ho tjhaja le kesi: 3,000 VAC ~ 50/60 Hz bakeng sa motsotso o le mong | |
| AC / DC voltagmofuta | Pakeng tsa karolo ea ho tjhaja le kesi: 2,000 VAC ~ 50/60 Hz bakeng sa motsotso o le mong | |
| Ho thothomela | 0.75 limilimithara ampmaqhubu a maqhubu a 5 ho isa ho 55 Hz ho e 'ngoe le e 'ngoe ea X, Y, Z
tataiso bakeng sa lihora tse 2 |
|
| Insulation resistance | ≥ 100 MΩ (500 VDC megger) | |
| Ho itšireletsa mafung | ± 2 kV lerata la sebopeho sa lisekoere ka simulator ea lerata (bophara ba pulse: 1 ㎲) R-mohato, S-mohato | |
| Ho boloka mohopolo | ≈ lilemo tse 10 (mofuta oa mohopolo o sa fetoheng oa semiconductor) | |
| Mocheso oa tikoloho | -10 ho 50 ℃, polokelo: -20 ho 60 ℃ (ha ho leqhoa kapa condensation) | |
| Mongobo wa tikoloho | 35 ho 85% RH, polokelo: 35 ho 85% RH (ha ho leqhoa kapa condensation) | |
| Sebopeho sa ts'ireletso | IP65 (Phanele e ka pele, litekanyetso tsa IEC)
• TK4SP: IP50 (Phanele e ka pele, maemo a IEC) |
|
|
Mofuta oa insulation |
Ho kenya habeli kapa ho tiisa matla (tšoaea:, matla a dielectric pakeng tsa karolo ea ho lekanya le karolo ea matla: 2 kV) | |
| Sesebedisoa | Bracket, sekoaelo sa tšireletso ea Terminal (TK4N) | |
| Kamohelo | ||
Sehokelo sa Puisano
RS485
| Comm. melaoana | Modbus RTU |
| Mofuta oa khokahano | RS485 |
| Tekanyetso ea kopo | EIA RS485 ho latela |
| Khokahano e phahameng | Li-unit tsa 31 (aterese: 01 ho isa ho 99) |
| Mokhoa o lumellanang | Asynchronous |
| Comm. Mokhoa | Terata e habeli ea terata e habeli |
| Comm. sebaka se sebetsang hantle | ≤ 800 limithara |
| Comm. lebelo | 2,400 / 4,800 / 9,600 (ea kamehla) / 19,200 / 38,400 bps (parameter) |
| Nako ea ho arabela | 5 ho isa ho 99 ms (ea kamehla: 20 ms) |
| Qala hanyane | 1 bit (e tsitsitseng) |
| Boitsebiso bo fokolang | 8 bit (e tsitsitseng) |
| Parity hanyane | Ha ho na (default), Odd, Even |
| Emisa hanyane | 1 bit, 2 bit (ka ho feletseng) |
| EEPROM potoloho ea bophelo | ≈ 1,000,000 ts'ebetso (Hlakola / Ngola) |
Mofuta oa ho Kena le Range ea ho Sebelisa
Lethathamo la li-setting tsa li-parameter tse ling li na le moeli ha u sebelisa pontšo ea lintlha tsa decimal.
| Mofuta oa ho kenya | Decimal
ntlha |
Pontšo | Ho sebelisa sebaka (℃) | Ho sebelisa sebaka (℉) | |||||
|
Thermo - banyalani |
K (CA) | 1 | KCaH | -200 | ho | 1,350 | -328 | ho | 2,462 |
| 0.1 | KCaL | -199.9 | ho | 999.9 | -199.9 | ho | 999.9 | ||
| J (IC) | 1 | JIcH | -200 | ho | 800 | -328 | ho | 1,472 | |
| 0.1 | JICL | -199.9 | ho | 800.0 | -199.9 | ho | 999.9 | ||
| E (CR) | 1 | ECrH | -200 | ho | 800 | -328 | ho | 1,472 | |
| 0.1 | ECRL | -199.9 | ho | 800.0 | -199.9 | ho | 999.9 | ||
| T (CC) | 1 | TCHH | -200 | ho | 400 | -328 | ho | 752 | |
| 0.1 | TCCL | -199.9 | ho | 400.0 | -199.9 | ho | 752.0 | ||
| B (PR) | 1 | B PR | 0 | ho | 1,800 | 32 | ho | 3,272 | |
| R (PR) | 1 | R PR | 0 | ho | 1,750 | 32 | ho | 3,182 | |
| TSE (PR) | 1 | S PR | 0 | ho | 1,750 | 32 | ho | 3,182 | |
| N (NN) | 1 | N NN | -200 | ho | 1,300 | -328 | ho | 2,372 | |
| C (TT) 01) | 1 | C TT | 0 | ho | 2,300 | 32 | ho | 4,172 | |
| G (TT) 02) | 1 | G TT | 0 | ho | 2,300 | 32 | ho | 4,172 | |
| L (IC) | 1 | LICH | -200 | ho | 900 | -328 | ho | 1,652 | |
| 0.1 | LICL | -199.9 | ho | 900.0 | -199.9 | ho | 999.9 | ||
| U (CC) | 1 | UCCH | -200 | ho | 400 | -328 | ho | 752 | |
| 0.1 | UCCL | -199.9 | ho | 400.0 | -199.9 | ho | 752.0 | ||
| Platinel II | 1 | PLII | 0 | ho | 1,390 | 32 | ho | 2,534 | |
|
RTD |
Cu50 Ω | 0.1 | LE 5 | -199.9 | ho | 200.0 | -199.9 | ho | 392.0 |
| Cu100 Ω | 0.1 | CU10 | -199.9 | ho | 200.0 | -199.9 | ho | 392.0 | |
| JPt100 Ω | 1 | JPthH | -200 | ho | 650 | -328 | ho | 1,202 | |
| 0.1 | JPtL | -199.9 | ho | 650.0 | -199.9 | ho | 999.9 | ||
| Tlhaloso: DPT50 Ω | 0.1 | DPT5 | -199.9 | ho | 600.0 | -199.9 | ho | 999.9 | |
| Tlhaloso: DPT100 Ω | 1 | DptH | -200 | ho | 650 | -328 | ho | 1,202 | |
| 0.1 | DptL | -199.9 | ho | 650.0 | -199.9 | ho | 999.9 | ||
| Nickel120 Ω | 1 | NI12 | -80 | ho | 200 | -112 | ho | 392 | |
|
Analoge |
0 ho 10 V | – | AV1 | 0 ho | 10 V | ||||
| 0 ho 5 V | – | AV2 | 0 ho | 5 V | |||||
| 1 ho 5 V | – | AV3 | 1 ho | 5 V | |||||
| 0 ho isa ho 100 mV | – | AMV1 | 0 ho | 100 mV | |||||
| 0 ho isa ho 20 mA | – | AMA1 | 0 ho | 20 mA | |||||
| 4 ho isa ho 20 mA | – | AMA2 | 4 ho | 20 mA | |||||
- C (TT): E ts'oana le sensor ea mofuta oa W5 (TT) e teng
- G (TT): E ts'oana le sensor ea mofuta oa W (TT) e teng
- Khanyetso ea mela e lumelletsoeng ka mola:
Bontša ho nepahala
| Mofuta oa ho kenya | Ho sebelisa mocheso | Bontša ho nepahala |
|
Thermo - RTD tse peli |
Ka mocheso oa kamore (23℃ ±5 ℃) |
(PV ±0.3% kapa ±1 ℃ e phahameng) ±-1-dijiti
• Thermocouple K, J, T, N, E ka tlase -100 ℃ le L, U, PII, RTD Cu50 Ω, Dpt50 Ω: (PV ±0.3% kapa ±2 ℃ e phahameng) ±1-dijiti • Thermocouple C, G le R, S ka tlase ho 200 ℃: (PV ±0.3% kapa ±3 ℃ e phahameng) ±-1-dijiti • Thermocouple B ka tlase ho 400 ℃: Ha ho na litekanyetso tsa ho nepahala |
|
Ho tsoa mochesong oa kamore |
(PV ±0.5% kapa ±2 ℃ e phahameng) ±-1-dijiti
• RTD Cu50 Ω, Dpt50 Ω: (PV ±0.5% kapa ±3 ℃ e phahameng) ±1-dijiti • Thermocouple R, S, B, C, G: (PV ±0.5% kapa ±5 ℃ e phahameng) ±-1-dijiti • Lisensara tse ling: ≤ ±5 ℃ (≤-100 ℃) |
|
|
Analoge |
Ka mocheso oa kamore
(23℃ ±5 ℃) |
± 0.3% FS ±-1-dijiti |
| Ho tsoa mochesong oa kamore | ± 0.5% FS ±-1-dijiti |
Litlhaloso tsa Yuniti
- Karolo ea pontšo ea PV (Khubelu)
- Mokhoa oa ho matha: E bonts'a PV (Boleng ba hona joale).
- Mokhoa oa ho seta: E bonts'a lebitso la parametha.
- Karolo e bonts'ang ea SV (Tala)
- Mokhoa oa ho matha: E bonts'a SV (Boleng ba ho beha).
- Mokhoa oa ho seta: E bonts'a boleng ba maemo a paramethara.
- Senotlolo sa ho kenya
Sesupo
| Pontšo | Lebitso | Tlhaloso |
| ℃,%, ℉ | Yuniti | E bonts'a karolo e khethiloeng (paramethara) |
| AT | Tokiso ea boiketsetso | E khanya nakong ea tokiso ea koloi motsotsoana o mong le o mong |
|
OUT1/2 |
Laola tlhahiso |
E BUA ha tlhahiso ea taolo e BUTSE
• Tlhahiso ea SSR (taolo ea potoloho/mohato) MV ho feta 5% ON • Sephetho sa hajoale Taolo ea matsoho: 0% OFF, ka holim'a ON Taolo ea Auto: ka tlase ho 2% OFF, ho feta 3% ON |
| AL1/2 | Phallo ea alamo | E BULE ha tlhahiso ea alamo e BUTSE |
| MONNA | Taolo ka letsoho | E BUA nakong ea taolo ea matsoho |
| SV1/2/3 | Mefuta e mengata ea SV | Letšoao la SV le ON le hlahang hajoale. (Ha u sebelisa mesebetsi e mengata ea SV) |
Kou ea thepa ea PC
Bakeng sa ho hokahanya converter ea puisano (SCM letoto).
- Bakeng sa lintlha tse mabapi le mofuta oa khale, sheba bukana ea mosebelisi. Khoasolla libuka tse tsoang ho Autonics websebaka.
Litekanyo
- Yuniti: mm, Bakeng sa litšoantšo tse qaqileng, latela Autonics websebaka.
- Ka tlase e thehiloe ho TK4S Series
Brakete
Sekoahelo sa tšireletso ea terminal
Mokhoa oa ho kenya
- Kamora ho kenya sehlahisoa ho phanele ka bracket, tiisa liboutu ka ho sebelisa screwdriver.
- Kenya yuniti ka har'a phanele, tiisa borakete ka ho sututsa ka screwdriver ea flathead.
Liphoso
| Pontšo | Kenyeletso | Tlhaloso | Sephetho | Ho batle phoso |
| Sensor ea mocheso | E benya ka nako ea metsotsoana e 0.5 ha sensor ea ho kenya e khaotsoe kapa sensor e sa hokahane. | 'Phoso ea sensor, MV' boemo ba boemo ba paramethara | Hlahloba boemo ba kutlo ea kutlo. | |
| BULETSE | ||||
|
Analoge |
E benya ka nako ea metsotsoana e 0.5 ha
ho kenya ho feta FS ±10%. |
'Phoso ea sensor,
MV' parameter ho beha boleng |
Sheba boemo ba ho kenya analoge. | |
| Sensor ea mocheso | E benya ka metsotsoana e 0.5 haeba boleng ba ho kenya bo ka holimo ho mefuta ea ho kenya. | Ho futhumatsa: 0%,
Pholiso: 100% |
||
| HHHH | ||||
|
Analoge |
E benya ka nako ea metsotsoana e 0.5 haeba e
boleng ba ho kenya bo feta 5 ho 10% ea holimo moeli kapa boleng bo tlase ba moeli. |
Tlhahiso e tloaelehileng |
Ha kenyelletso e le kahara palo e kalohileng ea ho kenya, pontšo ena ea nyamela. | |
| Sensor ea mocheso | E benya ka metsotsoana e 0.5. linako haeba boleng ba ho kenya bo ka tlase ho sebaka sa ho kenya. | Ho futhumatsa: 100%,
Pholiso: 0% |
||
| TLHALA | ||||
|
Analoge |
E benya ka nako ea metsotsoana e 0.5 haeba e
boleng ba tlhahiso ke ka holimo ho 5 ho 10% ea tlase moeli kapa boleng bo phahameng ba moeli. |
Tlhahiso e tloaelehileng |
||
|
ERR |
Sensor ea mocheso | E benya ka metsotsoana e 0.5 ha ho na le phoso ea ho seta 'me e khutlela skrineng sa phoso. |
– |
Sheba mokhoa oa ho beha. |
| Analoge |
Lihokelo
- Li-terminals tse nang le moriti ke mohlala o tloaelehileng.
- Kenyelletso ea dijithale ha e kenngoe ka motlakase ho tsoa lipotolohong tse kahare, ka hona e lokela ho bolokoa ha o hokahanya lipotoloho tse ling.
TK4N
TK4S
TK4SP
TK4M
TK4H / W / L
Litlhaloso tsa Crimp Terminal
- Yuniti: mm, Sebelisa terminal ea crimp ea sebopeho sa ho latela.
Pontšo ea Pele Ha Motlakase o BUTSE
Ha motlakase o fanoe, ka mor'a hore pontšo eohle e tla benya bakeng sa 1 sec, lebitso la mohlala le hlahisoa ka tatellano. Ka mor'a hore mofuta oa sensor ea ho kenya o bonese habeli, kena ho RUN mode.
Mode Setting
- Haeba ho na le mohlala oa TK4N / 4S / 4SP, tobetsa e khutšoanyane ea [MODE] e nka sebaka sa [A/M] ea tšebetso.
Tlhophiso ea Parameter
- Li-parameter tse ling lia etsoa / ha li sebetse ho latela mohlala kapa litlhophiso tsa liparamente tse ling.
- Karolo ea 'Parameter mask', e patang liparamente tse sa hlokahaleng kapa tse sa sebetseng, le karolo ea 'User parameter group', e behang liparamente tse itseng tse sebelisoang khafetsa, kapele le ha bonolo, e ka hlophisoa ho DAQMaster.
- Sheba bukana ea mosebelisi bakeng sa lintlha.
Sehlopha sa 1 sehlopha
Sehlopha sa 2 sehlopha
Sehlopha sa 3 sehlopha
Sehlopha sa 4 sehlopha
Sehlopha sa 5 sehlopha
18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Rephabliki ea Korea, 48002 www.autonics.com | +82-2-2048-1577 | thekiso@autonics.com
Litokomane / Lisebelisoa
 |
Autonics TCD210240AC Lilaoli tsa Mocheso ka nako e le 'ngoe le Mohatsela oa PID [pdf] Buka ea Taelo TCD210240AC Ka nako e le 'ngoe Ho futhumatsa le ho Pholisa Poelo ea PID Ba laolang mocheso, TCD210240AC, Lilaoli tsa Mocheso ka nako e le 'Ngoe le Mohatsela oa PID, Lilaoli tsa Mocheso oa Mocheso oa Mocheso oa Mocheso, Lilaoli tsa Mocheso oa Mocheso oa PID, Lilaoli tsa Mocheso oa PID, Lilaoli tsa Mocheso oa Mocheso, Lilaoli tsa Mocheso ID. rs |
