ARTERY AT-START-F413 Boto ea Nts'etsopele ea Li-Microcontrollers
Tlhahisoleseding ya Sehlahiswa
AT-START-F413 ke boto ea tlhahlobo e thehiloeng ho chip ea AT32F413RCT7. E na le matšoao a LED, likonopo, sehokelo sa USB micro-B, sehokelo sa katoloso ea Arduino Uno R3, le mohopolo o atolositsoeng oa 16 MB SPI Flash. Boto e boetse e kenyelletsa sesebelisoa sa AT-Link-EZ debugging/programming, ho felisa tlhoko ea lisebelisoa tse ling tsa ntlafatso.
Boto e etselitsoe ho fana ka sethala se bonolo sa ho lekola le ho nts'etsapele lits'ebetso ho sebelisa chip ea AT32F413RCT7.
Litaelo tsa Tšebeliso ea Sehlahisoa
Qala ka Potlako:
Ho qala ka boto ea AT-START-F413, latela mehato ena:
- Hokela boto ho phepelo ea motlakase u sebelisa mohloli o loketseng oa matla.
- Hokela boto khomphuteng u sebelisa sehokelo sa USB Micro-B.
- Kenya lisebelisoa tse hlokahalang tse tšehetsang AT-START-F413 komporong ea hau.
- Sheba karolo ea hardware le moralo oa bukana ea mosebedisi bakeng sa tlhahisoleseding mabapi le likarolo tse fapaneng le lihokelo tse holim'a boto.
Lisebelisoa tse tšehetsang AT-START-F413:
Boto ea AT-START-F413 e tsamaellana le lisebelisoa tse khethehileng tsa ho etsa mananeo le ho lokisa liphoso. Sheba litokomane tse fanoeng le boto bakeng sa lethathamo la liketane tse tšehetsoeng le litaelo tsa ho li kenya.
Hardware le moralo:
Karolo ea Hardware le sebopeho sa buka ea mosebelisi e fana ka tlhaiso-leseling e felletseng mabapi le bokhoni ba ho hlophisa le ho lokisa boto, khetho ea phepelo ea matla, matšoao a LED, likonopo, mehloli ea oache, khetho ea mokhoa oa boot, ts'ebetso ea sesebelisoa sa USB, khokahanyo ea memori ea Flash, meralo ea mohanyetsi, le lihokelo tsa katoloso (sehokelo sa katoloso ea Arduino Uno R3 le sehokelo sa boema-kepe sa LQFP64 I/O).
Sekema:
Karolo ea moralo oa buka ea mosebelisi e na le setšoantšo se qaqileng sa motlakase sa boto ea AT-START-F413. Sheba karolo ena bakeng sa kutloisiso e batsi ea potoloho ea boto.
Selelekela
AT-START-F413 e etselitsoe ho u thusa ho hlahloba likarolo tse sebetsang hantle tsa 32-bit microcontroller, AT32F413 e kentsoeng ka ARM Cortex.
®-M4F ea mantlha e nang le FPU, 'me e u thusa ho ntlafatsa lits'ebetso tsa hau.
AT-START-F413 ke boto ea tlhahlobo e thehiloeng ho chip ea AT32F413RCT7 e nang le matšoao a LED, likonopo, sehokelo sa USB micro-B, sehokelo sa ArduinoTM Uno R3 le memori e atolositsoeng ea 16 MB SPI Flash. Boto ena ea tlhahlobo e kenyelletsa sesebelisoa sa ho lokisa / ho hlophisa AT-Link-EZ ntle le tlhoko ea lisebelisoa tse ling tsa nts'etsopele.
Likaroloana
- AT-START-F413 e na le litšobotsi tse latelang:
- AT-START-F413 e na le microcontroller e holim'a board ea AT32F413RCT7 e kenyang ARM Cortex®-M4F, processor ea 32-bit, 256 KB Flash memory le 32 KB SRAM, liphutheloana tsa LQFP64.
- Sehokelo sa AT-Link se ka botong:
- AT-Link-EZ e ka har'a board e ka sebelisoa bakeng sa ho etsa mananeo le ho lokisa liphoso (AT-Link-EZ ke mofuta o nolofalitsoeng oa AT-Link, 'me ha e tšehetse mokhoa oa offline)
- Haeba AT-Link-EZ e arohane le boto ena ka ho inamela haufi le lenonyeletso, AT-START-F413 e ka hokela ho AT-Link e ikemetseng bakeng sa ho etsa mananeo le ho lokisa liphoso.
- Ka har'a board 20-pin ARM standard JTAG sehokelo (se nang le JTAG/ sehokelo sa SWD bakeng sa ho hlophisa / ho lokisa liphoso)
- 16 MB SPI Flash EN25QH128A e sebelisoa joalo ka memori e atolositsoeng ea Flash 3
- Mekhoa e fapaneng ea ho fana ka motlakase:
- Ka bese ea USB ea AT-Link-EZ
- Ka bese ea USB (VBUS) ea AT-START-F413
- Matla a kantle a 7~12 V (VIN)
- Matla a kantle a 5 V (E5V)
- Matla a kantle a 3.3 V
- 4 x matšoao a LED:
- LED1 (e khubelu) e sebelisetsoang motlakase oa 3.3 V
- 3 x USER LED, LED2 (khubelu),LED3 (e tšoeu) le LED4 (e tala)
- 2 x likonopo (konopo ea mosebelisi le konopo ea reset)
- 8 MHz HSE kristale
- 32.768 kHz LSE kristale
- Sehokelo sa USB micro-B
- Lihokelo tsa katoloso ea Varioius li ka hokahanngoa kapele ka har'a boto ea mohlala mme ho bonolo ho e hlahloba:
- Sehokelo sa katoloso ea ArduinoTM Uno R3
- LQFP64 I/O sehokelo sa katoloso
Lipehelo tse tloaelehileng
Lethathamo la 1 e bontsha ditlhaloso tsa melawana e meng e sebediswang tokomaneng ena.
Letlapa la 1. Tlhaloso ea ON/OFF
| Tloaelehileng dipehelo | Tlhaloso |
| Jumper JPx ON | Jumper e kentsoe |
| Jumper JPx OFF | E tlole ha ea kengoa |
| Mohanyetsi Rx ON | Potoloho e khuts'oane ka solder kapa 0Ω resistor |
| Mohanyetsi Rx OFF | Bula |
Ho qala ka potlako
AT-START-F413 ke sesebelisoa sa nts'etsopele se theko e tlase ebile se bonolo ho se sebelisa se etselitsoeng ho lekola kapele le ho sebelisa li-microcontrollers tse sebetsang hantle tsa AT32F413 ho nts'etsapele lits'ebetso.
Qala
Lokisa boto ea AT-START-F413 ka tatellano e latelang ho qala ts'ebeliso:
- Sheba boemo ba Jumper botong:
JP1 e hokahane le GND kapa OFF (BOOT0 pin ke 0, 'me BOOT0 e na le mochine oa ho hula fatše ho AT32F413RCT7);
JP4 ea boikhethelo kapa OFF (BOOT1 e boemong bofe kapa bofe);
jumper ea karolo e le 'ngoe ea JP8 e hokahane le I/O ka ho le letona. - Hokela boto ea AT-START-F413 ho PC ka thapo ea USB (Mofuta oa A ho isa ho micro-B), 'me boto e tla tsamaisoa ka sehokelo sa USB sa AT-Link-EZ CN6. LED1 (e khubelu) e lula e le teng, 'me li-LED tse ling tse tharo (LED2 ho ea ho LED4) li qala ho panya ka ho latellana.
- Kamora ho tobetsa konopo ea USER (B2), maqhubu a ho panya ha li-LED tse tharo a fetoloa
Lisebelisoa tse tšehetsang AT-START-F413
- ARM® Keil®: MDK-ARM™
- IAR™: EWARM
Hardware le moralo
Boto ea AT-START-F413 e entsoe ho potoloha microcontroller ea AT32F413RCT7 ka har'a sephutheloana sa LQFP64.
Setšoantšo sa 2 e bonts'a likhokahano lipakeng tsa AT-Link-EZ, AT32F413RCT7 le lisebelisoa tsa tsona (likonopo, li-LED, USB, SPI Flash memori le lihokelo tse atolositsoeng)
Setšoantšo sa 3 'me Setšoantšo sa 4 se bontša likarolo tsena ho AT-Link-EZ le AT-START-F413 boto.
Mananeo le debugging
- E kenyelelitsoe AT-Link-EZ
Boto ea tlhahlobo e kenyelletsa sesebelisoa sa lenaneo la Artery AT-Link-EZ le sesebelisoa sa ho rarolla mathata bakeng sa basebelisi ho hlophisa / ho lokisa AT32F413RCT7 botong ea AT-START-F413. AT-Link-EZ e ts'ehetsa SWD interface mode mme e ts'ehetsa sehlopha sa likou tsa COM (VCP) ho hokela ho USART1_TX/USART1_RX (PA9/PA10) ea AT32F413RCT7. Tabeng ena, PA9 le PA10 tsa AT32F413RCT7 li tla angoa ke AT-Link-EZ ka tsela e latelang:- PA9 e huloa ka bofokoli ho ea boemong bo phahameng ka pinana ea VCP RX ea AT-Link-EZ;
- PA10 e huleloa ka matla ho isa boemong bo holimo ke phini ea VCP TX ea AT-Link-EZ
Mosebelisi a ka beha R9 le R10 OFF, joale tšebeliso ea PA9 le PA10 ea AT32F413RCT7 ha e tlas'a lithibelo tse ka holimo.
Ka kopo sheba buka ea AT-Link User Manual bakeng sa lintlha tse felletseng mabapi le ts'ebetso, ntlafatso ea firmware le litemoso tsa AT-Link-EZ.
AT-Link-EZ PCB e botong ea tlhahlobo e ka aroloa ho AT-START-F413 ka ho inamela holim'a lenonyeletso. Tabeng ena, AT-START-F413 e ntse e ka hokahanngoa le CN7 ea AT-Link-EZ ka CN2 (e sa kenngoeng pele e romelloa), kapa e ka hokahanngoa le AT-Link e 'ngoe ho ntšetsa pele lenaneo le debugging ho AT32F413RCT7.
- 20-pin ARM® standard JTAG sehokedi
AT-START-F413 e boetse e boloka JTAG kapa likhokahano tsa sepheo se akaretsang sa SWD joalo ka lisebelisoa tsa ho hlophisa / ho lokisa liphoso. Haeba mosebelisi a batla ho sebelisa sebopeho sena ho hlophisa le ho lokisa AT32F413RCT7, ka kopo arola AT-Link-EZ ho boto ena kapa u behe R41, R44 le R46 OFF, 'me u hokele CN3 (e sa kengoang pele e romelloa) lenaneong le ho lokisa liphoso. sesebelisoa.
Khetho ea phepelo ea motlakase
Matla a 5 V a AT-START-F413 a ka fanoa ka thapo ea USB (ebang ke ka sehokelo sa USB CN6 ho AT-Link-EZ kapa sehokelo sa USB CN1 ho AT-START-F413), kapa ka 5 ea kantle. Phepelo ea matla a V (E5V), kapa ka matla a kantle a 7 ~ 12 V (VIN) ka 5V vol.tage regulator (U1) ka boto. Tabeng ena, matla a 5 V a fana ka matla a 3.3 V a hlokoang ke li-microcontroller le li-peripherals ka matla a 3.3 V.tage regulator (U2) ka boto.
Pini ea 5 V ea J4 kapa J7 e ka boela ea sebelisoa e le mohloli oa matla a ho kenya. Boto ea AT-START-F413 e tlameha ho tsamaisoa ke yuniti ea phepelo ea matla a 5 V.
Pini ea 3.3 V ea J4 kapa phini ea VDD ea J1 le J2 le eona e ka sebelisoa ka kotloloho e le phepelo ea motlakase ea 3.3 V. Boto ea AT-START-F413 e tlameha ho tsamaisoa ke yuniti ea phepelo ea motlakase ea 3.3 V.
Hlokomela: Ntle le haeba 5 V e fanoa ka sehokelo sa USB (CN6) ho AT-Link-EZ, AT-Link-EZ e ke ke ea tsamaisoa ke mekhoa e meng ea phepelo ea motlakase.
Ha boto e 'ngoe ea kopo e hokahane le J4, pin VIN, 5 V le 3.3 V e ka sebelisoa e le matla a tlhahiso; J7 5V pin e sebelisoang e le matla a tlhahiso ea 5 V; pinana ea VDD ea J1 le J2 e sebelisoang e le matla a tsoang ho 3.3 V.
Lipontšo tsa LED
- Matla a LED1: bofubelu bo bontša hore boto e tsamaisoa ke 3.3 V
- Mosebelisi LED2: e khubelu, e hokahane le phini ea PC2 ea AT32F413RCT7
- LED3 ea mosebelisi: e tšoeu, e hokahane le phini ea PC3 ea AT32F413RCT7
- LED4 ea mosebelisi: e tala, e hokahaneng le pini ea PC5 ea AT32F413RCT7
Likonopo
Seta konopo ea B1: e hokahantsoeng ho NRST ho seta bocha AT32F413RCT7
Konopo ea mosebelisi B2: ke, ka ho sa feleng, e hokahane le PA0 ea AT32F413RCT7, 'me ka tsela e 'ngoe e sebelisoa e le konopo ea ho tsosa (R19 ON, R21 OFF); Kapa e hokahane le PC13 mme ka tsela e 'ngoe e sebelisoa joalo ka TAMPKonopo ea ER-RTC (R19 OFF, R21 ON)
IDD
Ketsahalong ea JP3 OFF (letšoao IDD) le R13 OFF, e lumelloa ho hokahanya ammeter ho lekanya tšebeliso ea matla ea AT32F413RCT7.
- JP3 OFF, R13 ON: AT32F413RCT77 e sebetsa (Setting ea kamehla, 'me plug ea JP3 ha e kentsoe pele e romelloa).
- JP3 ON, R13 OFF: AT32F413RCT7 e tsamaisoa.
- JP3 OFF, R13 OFF: ammeter e tlameha ho hokeloa ho lekanya tšebeliso ea matla ea AT32F413RCT7 (haeba ho se na ammeter, AT32F413RCT7 e ke ke ea tsamaisoa).
Mohloli oa oache oa kantle
- Mohloli oa oache oa HSE
Ho na le mekhoa e meraro ea lisebelisoa tsa ho beha mehloli ea lioache tse lebelo le holimo:- kristale e ka holim'a board (setting ea kamehla): kristale ea 8 MHz boto e sebelisoa e le mohloli oa oache oa HSE. Setting ea hardware e tlameha ho ba: R1 le R15 ON, R14 le R16 OFF
- Oscillator e tsoang ka ntle ho PD0: oscillator ea ka ntle e kenngoa ho tloha pineng ea 5 ea J2. Setting ea hardware e tlameha ho ba: R14 le R16 ON, R1 le R15 OFF.
- HSE ha e sebelisoe: PD0 le PD1 li sebelisoa e le GPIO. Setting ea hardware e tlameha ho ba: R14 le R16 ON, R1 le R15 OFF.
- Mohloli oa oache oa LSE
Ho na le mekhoa e meraro ea lisebelisoa tsa ho beha mehloli ea oache e lebelo le tlase:- kristale e ka holim'a board (setting ea kamehla): kristale ea 32.768 kHz boto e sebelisoa e le mohloli oa oache oa LSE. Setting ea hardware e tlameha ho ba: R6 le R7 ON, R5 le R8 OFF
- Oscillator e tsoang kantle ho PC14: oscillator ea kantle e kenngoa ho tloha J2 pin_3. Setting ea hardware e tlameha ho ba: R5 le R8 ON, R6 le R7 OFF.
- LSE ha e sebelisoe: PC14 le PC15 li sebelisoa e le GPIO. Setting ea hardware e tlameha ho ba: R5 le R8 ON, R6 le R7 OFF.
Khetho ea mokhoa oa ho qala
Ha u qala, ho ka khethoa mekhoa e meraro e fapaneng ea boot ka ho sebelisa li-pin configuration.
Lethathamo la 2. Setlhophiso sa jumper ea khetho ea mokhoa oa boot
|
Jumper |
Lithapa tsa khetho ea mokhoa oa boot |
Litlhophiso |
||
| BOTSOA1 | BOTSOA0 | |||
| JP1 e amanang le GND kapa OFF;
JP4 ea boikhethelo kapa e TLOHILE |
X | 0 | Qala ho tloha memori ea Flash e ka hare ka jumper
maemo a ka tlase: (Ka kamehla, JP1 e hoketsoe ho GND) |
|
 |
||||
| JP1 e hoketsoeng ho VDD JP4 e hoketsoeng ho GND | 0 | 1 | Qala ho tloha memoring ea sistimi ka sethala sa jumper se ka tlase:
|
|
| JP1 e hoketsoeng ho VDD JP4 e hoketsoeng ho VDD | 1 | 1 | Boot ho tloha ho SRAM ka sethala sa jumper se ka tlase:
|
|
Sesebelisoa sa USB
Boto ea AT-START-F413 e ts'ehetsa puisano ea sesebelisoa sa USB ka lebelo le felletseng ka sehokelo sa USB Micro-B (CN1). VBUS e ka sebelisoa e le matla a 5 V a boto ea AT-START-F413.
Hokela ho Bank3 ea memori ea Flash ka sebopeho sa SPIM
SPI Flash EN25QH128A botong e hokahane le AT32F413RCT7 ka sebopeho sa SPIM mme e sebelisoa e le Bank 3 ea memori ea Flash e atolositsoeng.
Ha u sebelisa Banka 3 ea memori ea Flash ka sebopeho sa SPIM, jumper ea karolo e le 'ngoe ea JP8, joalokaha e bontšitsoe Lethathamong la 3, e lokela ho khetha lehlakore le letšehali la SPIM. Tabeng ena, PB1, PA8, PB10 PB11, PB6 le PB7 ha li kopane le sehokelo sa katoloso sa LQFP64 I/O sa kantle. Lithakhisa tsena tse 6 li tšoailoe ka ho kenyelletsa [*] ka mor'a lebitso la phini la sehokelo sa sehokelo ho sekirini sa silika sa PCB.
Lethathamo la 3. IO le SPIM jumper setting
| Jumper | Litlhophiso |
| JP8 e hokahane le lehlakore la IO | Ho sebelisa ts'ebetso ea IO, jumper e kentsoe ka tsela e latelang: (Setsi sa kamehla pele se romelloa)
|
| JP8 e hokahane le lehlakore la SPIM | Ho sebelisa ts'ebetso ea SPIM, jumper e kentsoe ka tsela e latelang: (Setsi sa kamehla pele se romelloa)
|
0 Ω lihanyetsi
Lethathamo la 4. 0 Ω tlhophiso ea sehanyetsi
| Mohanyetsi | Naha(1) | Tlhaloso |
|
R13 (Tekanyo ea tšebeliso ea matla a Microcontroller) |
ON |
Ha JP3 e TLOhile, 3.3V e hokela ho microcontroller ho
fana ka phepelo ea motlakase |
|
TLOA |
Ha JP3 e TLOhile, 3.3V e lumella ammeter hore e hokahane ho lekanya tšebeliso ea matla ea microcontroller (haeba ho se na ammeter, microcontroller e ke ke ea tsamaisoa) | |
| R4
(Motlakase oa VBAT) |
ON | VBAT e tlameha ho hokela VDD |
| TLOA | VBAT e ka tsamaisoa ke 1st pin VBAT ea J2 | |
|
R1, R14, R15, R16 (HSE) |
ON, TIMELA, BUTSE, TLWA | Mohloli oa oache oa HSE o sebelisa kristale Y2 botong |
|
TIMA, BUTSA, TIMA, BUTSE |
Mohloli oa oache oa HSE o tsoa PD0 ea kantle kapa PD0 le PD1 li
e sebelisoa e le GPIO. |
|
|
R5, R6, R7, R8 (LSE) |
TIMA, BUTSE, BUTSE, TIMA | Mohloli oa oache oa LSE o sebelisa kristale Y1 ka boto |
|
ON, TIMA, TIMA, BUTSE |
Mohloli oa oache oa LSE o tsoa ho PC14 ea kantle kapa PC14 le PC15
li sebelisoa e le GPIO. |
|
| R19, R21
(konopo ea USER B2) |
ON, TSOANG | Konopo ea mosebelisi B2 e hokahane le PA0 |
| TIMA, TS'OELE | Konopo ea mosebelisi B2 e hokahane le PC13 | |
|
R29, R30 (PA11, PA12) |
TIMA, TLOA |
Ha PA11 le PA12 li sebelisoa joalo ka USB, ha li joalo
e hokahane le pin_12 le pin_13 ea J1 |
|
TSOELA, TSOELA |
Ha PA11 le PA12 li sa sebelisoe joalo ka USB, li ka ba joalo
e hokahane le pin_12 le pin_13 ea J1 |
|
|
R31, R32, R33, R34 (ArduinoTM A4, A5) |
TIMA, BON, TIMA, ON |
ArduinoTM A4 le A5 li hokahane le ADC_IN11 le
ADC_IN10 |
|
ON, TIMELA, BUTSE, TLWA |
ArduinoTM A4 le A5 e hokahane le I2C1_SDA le
I2C1_SCL |
|
| R35, R36
(ArduinoTM D10) |
TIMA, ON | ArduinoTM D10 e hoketsoe ho SPI1_SS |
| ON, TSOANG | ArduinoTM D10 e hoketsoe ho PWM (TMR4_CH1) | |
|
R9 (UART1_RX) |
ON |
USART1_RX ea AT32F413RCT7 e hokahane le VCP TX ea
AT-Link-EZ |
|
TLOA |
USART1_RX ea AT32F413RCT7 e khaotsoe ho VCP TX
ea AT-Link-EZ |
|
|
R10 (UART1_TX) |
ON |
USART1_TX ea AT32F413RCT7 e hokahane le VCP RX ea
AT-Link-EZ |
|
TLOA |
USART1_TX ea AT32F413RCT7 e khaotsoe ho VCP RX
ea AT-Link-EZ |
- Boemo ba kamehla ba feme ea Rx bo bontšoa ho BOLD.
Lihokelo tsa katoloso
- Sehokelo sa katoloso ea ArduinoTM Uno R3
Plaka ea basali J3~J6 le sehokelo sa monna J7 se tloaelehileng sa ArduinoTM Uno R3. Bongata ba mapolanka a barali a etselitsoeng haufi le Arduino TM Uno R3 a loketse AT-START-F413.
Hlokomela
- Likou tsa I/O tsa AT32F413RCT7 ke 3.3 V e lumellanang le ArduinoTM Uno R3, empa 5V ha e lumellane.
- Pin_8 ea J3 ke VDDA, e nang le boemo bo lekanang le VDD, ntle le mosebetsi oa AFEF o hlalosoang ke ArduinoTM Uno R3.
Lethathamo la 5. Tlhaloso ea phini ea sehokelo sa ArduinoTM Uno R3
|
Sehokedi |
Nomoro ea phini |
Arduino
pin lebitso |
AT32F413
pin lebitso |
Mesebetsi |
|
J4 (Phepelo ea motlakase) |
1 | NC | - | - |
| 2 | IOREF | - | Tlhaloso ea 3.3V | |
| 3 | RETS'ELISITSOE | NRST | Ho tsosolosa ka ntle | |
| 4 | 3.3V | - | 3.3V kenyeletso/ho tsoa | |
| 5 | 5V | - | 5V kenyeletso/ho tsoa | |
| 6 | GND | - | Fatše | |
| 7 | GND | - | Fatše | |
| 8 | VIN | - | 7 ~ 12V tlhahiso / tlhahiso | |
|
J6 (Mongolo oa analog) |
1 | A0 | PA0 | ADC12_IN0 |
| 2 | A1 | PA1 | ADC12_IN1 | |
| 3 | A2 | PA4 | ADC12_IN4 | |
| 4 | A3 | PB0 | ADC12_IN8 | |
| 5 | A4 | PC1 kapa PB9(1) | ADC12_IN11 kapa I2C1_SDA | |
| 6 | A5 | PC0 kapa PB8(1) | ADC12_IN10 kapa I2C1_SCL | |
|
J5 (Moputso oa kelello / tlhahiso e tlase) |
1 | D0 | PA3 | UART2_RX |
| 2 | D1 | PA2 | UART2_TX | |
| 3 | D2 | PA10 | - | |
| 4 | D3 | PB3 | TMR2_CH2 | |
| 5 | D4 | PB5 | - | |
| 6 | D5 | PB4 | TMR3_CH1 | |
| 7 | D6 | PB10 | TMR2_CH3 | |
| 8 | D7 | PA8(2) | - | |
|
J3 (Moputso oa logic/output high byte) |
1 | D8 | PA9 | - |
| 2 | D9 | PC7 | TMR8_CH2 | |
| 3 | D10 | PA15 kapa PB6(1)(2) | SPI1_NSS kapa TMR4_CH1 | |
| 4 | D11 | PA7 | TMR3_CH2 kapa SPI1_MOSI | |
| 5 | D12 | PA6 | SPI1_MISO | |
| 6 | D13 | PA5 | SPI1_SCK | |
|
7 |
GND |
- |
Fatše |
|
| 8 | VDDA | - | Tlhahiso ea VDDA | |
| 9 | SDA | PB9 | I2C1_SDA | |
| 10 | SCL | PB8 | I2C1_SCL |
|
J7 (Ba bang) |
1 | MISO | PB14 | SPI2_MISO |
| 2 | 5V | - | 5V kenyeletso/ho tsoa | |
| 3 | TS'ELISO | PB13 | SPI2_SCK | |
| 4 | MOSI | PB15 | SPI2_MOSI | |
| 5 | RETS'ELISITSOE | NRST | Ho tsosolosa ka ntle | |
| 6 | GND | - | Fatše | |
| 7 | NSS | PB12 | SPI2_NSS | |
| 8 | PB11 | PB11 | - |
- 0Ω setting ea resistor e bontšoa ho Lethathamo la 4.
- SPIM e tlameha ho holofala mme JP8-piece-piece jumper e tlameha ho khetha I/O, ho seng joalo PA8 le PB6 li ke ke tsa sebelisoa.
Sehokelo sa katoloso ea koung ea LQFP64 I/O
Lihokelo tsa katoloso J1 le J2 li ka hokela AT-START-F413 ho prototype ea kantle / boto ea ho paka. Likou tsa I/O tsa AT32F413RCT7 lia fumaneha lihokelong tsena tsa katoloso. J1 le J2 le tsona li ka lekanyetsoa ka probe ea oscilloscope, logic analyzer kapa voltmeter.
Leano
Nalane ea ntlafatso
Lethathamo la 6. Nalane ea ntlafatso ea litokomane
| Letsatsi | Khatiso | Liphetoho |
| 2019.2.12 | 1.0 | Tokollo ea pele |
|
2019.9.20 |
1.1 |
1. E kentse AT-Link-EZ
2. E lokisitse silika ea CN2 USART1_TX le USART1_RX 3. Mohanyetsi oa 0Ω o fetotsoeng hore e be borokho ba solder 4. CB8 e fetotsoeng ho ba 1μF 5. Fetotse voltage regulator (U2) le lisebelisoa tse amanang le kantle |
TSEBISO EA BOHLOKOA - KA KOPO BALA KA HLOKO
Bareki ba utloisisa le ho lumela hore bareki ke bona feela ba ikarabellang bakeng sa khetho le tšebeliso ea lihlahisoa le litšebeletso tsa Artery.
Lihlahisoa le litšebeletso tsa Artery li fanoa ka "JOALOKAHA" 'me Artery ha e fane ka litiisetso tse hlalosoang, tse boleloang kapa tse molaong, ho kenyeletsoa, ntle le moeli, litiisetso life kapa life tse boletsoeng tsa thekiso, boleng bo khotsofatsang, ho se tlole molao, kapa ho phela hantle molemong oa morero o itseng mabapi le Arteri's. lihlahisoa le litšebeletso.
Leha ho le joalo, bareki ha ba fumane tokelo, tlotla kapa thahasello ho lihlahisoa le litšebeletso tsa Artery kapa litokelo life kapa life tsa thepa ea mahlale tse kenyellelitsoeng ho eona. Leha ho le joalo, lihlahisoa le litšebeletso tsa Artery li ke ke tsa hlalosoa e le (a) ho fana ka bareki, ka ho hlaka kapa ka moelelo, estoppel kapa ka tsela e 'ngoe, laesense ea ho sebelisa lihlahisoa le litšebeletso tsa batho ba bang; kapa (b) ho fana ka laesense litokelo tsa thepa ea bohlale tsa batho ba boraro; kapa (c) ho fana ka tumello ea lihlahisoa le litšebeletso tsa motho e mong le litokelo tsa eona tsa thepa ea mahlale.
Bareki ba lumela hore lihlahisoa tsa Artery ha lia lumelloa ho sebelisoa e le, 'me bareki ba ke ke ba kopanya, ho khothaletsa, ho rekisa kapa ho fetisetsa sehlahisoa sefe kapa sefe sa Artery ho moreki ofe kapa ofe kapa mosebelisi oa ho qetela bakeng sa ho sebelisoa e le likarolo tsa bohlokoa ho (a) meriana efe kapa efe, pholoso ea bophelo kapa bophelo. sesebediswa sa tshehetso kapa tsamaiso, kapa (b) sesebediswa sefe kapa sefe sa polokeho tshebedisong efe kapa efe ya koloi le motjhini (ho kenyeletswa empa ho sa felle feela ho disistimi tsa mariki kapa mekotla ya moya), kapa (c) disebediswa dife kapa dife tsa nyutlelie, kapa (d) sesebediswa sefe kapa sefe sa taolo ya sephethephethe sa moyeng. , kopo kapa tsamaiso, kapa (e) sesebelisoa leha e le sefe sa libetsa, ts'ebeliso kapa tsamaiso, kapa (f) sesebelisoa leha e le sefe, ts'ebeliso kapa tsamaiso moo ho ka lebelloang pele hore ho hlōleha ha lihlahisoa tsa Artery joalo ka ha li sebelisoa mochine o joalo, ts'ebeliso kapa tsamaiso e ka lebisa. ho isa lefung, kotsi ya mmele kapa tshenyo e mpe ya thepa.
© 2020 ARTERY Technology Corporation - Litokelo tsohle li sirelelitsoe
Litokomane / Lisebelisoa
 |
ARTERY AT-START-F413 Boto ea Nts'etsopele ea Li-Microcontrollers [pdf] Bukana ea Mosebelisi AT-START-F413 Development Board For Microcontrollers, AT-START-F413, Development Board For Microcontrollers, For Microcontrollers, Microcontrollers |
