Arduino® Nano ESP32
Sehlahisoa Reference Manual
SKU: ABX00083
Nano ESP32 e nang le Lihlooho
Tlhaloso
Arduino Nano ESP32 (e nang le lihlooho le ntle le lihlooho) ke Nano form factor board e thehiloeng ho ESP32-S3 (e kentsoeng ho NORA-W106-10B ho tloha u-blox®). Ena ke boto ea pele ea Arduino e thehiloeng ka botlalo ho ESP32, 'me e fana ka Wi-Fi® hammoho le Bluetooth® LE.
Nano ESP32 e tsamaisana le Arduino Cloud, 'me e na le tšehetso bakeng sa MicroPython. Ke boto e loketseng ho qala ka nts'etsopele ea IoT.
Libaka tse reriloeng:
Moetsi, IoT, MicroPython
Likaroloana
Xtensa® Dual-core 32-bit LX7 Microprocessor
- Ho fihla ho 240 MHz
- 384kB ROM
- 512 kB SRAM
- 16 kB SRAM ho RTC (mokhoa o tlase oa matla)
- Molaoli oa DMA
Matla
- Tshebetso voltage 3.3v
- VBUS e fana ka 5 V ka sehokelo sa USB-C®
- Boemo ba VIN ke 6-21 V
Khokahano
- WiFi®
- Bluetooth® LE
- Lenakana le hahelletsoeng
- 2.4 GHz transmitter/receiver
- Ho fihlela ho 150 Mbps
Lithako
- 14x dijithale (21x ho kenyelletsa analog)
- 8x analog (e fumaneha ka mokhoa oa RTC)
- SPI(D11,D12,D13), I2C (A4/A5), UART(D0/D1)
Li-Ports tsa puisano
- SPI
- I2C
- I2S
- UART
- KA (TWAI®)
Matla a Tlase
- 7 μA tšebeliso ea boroko bo tebileng *
- 240 μA ho sebelisoa ka mokhoa o bobebe oa ho robala*
- Memori ea RTC
- Ultra Low Power (ULP) Coprocessor
- Setsi sa Tsamaiso ea Matla (PMU)
- ADC ka mokhoa oa RTC
*Litekanyetso tsa tšebeliso ea matla tse thathamisitsoeng mekhoeng ea matla a tlase ke tsa ESP32-S3 SoC feela. Likarolo tse ling tsa boto (tse kang li-LED), le tsona li sebelisa matla, e leng ho eketsang tšebeliso ea matla ka kakaretso ea boto.
Boto
Nano ESP32 ke boto ea nts'etsopele ea 3.3 V e thehiloeng ho NORA-W106-10B ho tloha u-blox®, module e kenyelletsang tsamaiso ea ESP32-S3 ho chip (SoC). Mojule ona o na le ts'ehetso bakeng sa Wi-Fi® le Bluetooth® Low Energy (LE), ka amppuisano e ntlafalitsoeng ka lenakana le ahelletsoeng ka hare. CPU (32-bit Xtensa® LX7) e ts'ehetsa maqhubu a oache ho fihla ho 240 MHz.
1.1 Kopo Examples
Home automation: boto e nepahetseng bakeng sa ho iketsetsa ntlo ea hau, 'me e ka sebelisoa bakeng sa liswichi tse bohlale, mabone a othomathike le taolo ea enjene, mohlala, li-blind tse laoloang ke enjene.
Li-sensor tsa IoT: tse nang le liteishene tse 'maloa tse inehetseng tsa ADC, libese tse fumanehang tsa I2C/SPI le module ea seea-le-moea e matla ea ESP32-S3, boto ena e ka sebelisoa habonolo ho lekola boleng ba sensor.
Meralo ea matla a tlase: theha lits'ebetso tse tsamaisoang ke betri ka tšebeliso e tlase ea matla, u sebelisa e hahiloeng ka mekhoa e tlase ea matla ea ESP32-S3 SoC.
Setšoantšo sa ESP32
Nano ESP32 e sebelisa Arduino Board Package bakeng sa liboto tsa ESP32, e nkiloeng ho Espressif's arduino-esp32 core.
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| VIN | Keletso voltage ho tloha VIN pad | 6 | 7.0 | 21 | V |
| VUSB | Keletso voltage ho tsoa ho sehokelo sa USB | 4.8 | 5.0 | 5.5 | V |
| Tambient | Ambient Mocheso | -40 | 25 | 105 | °C |
E sebetsa hapeview
Setšoantšo se Thibeloang
Board Topology
5.1 Ka pele View
View ho tloha ka holimo lehlakoreng
Holimo View ea Arduino Nano ESP32
| Ref. | Tlhaloso |
| M1 | NORA-W106-10B (ESP32-S3 SoC) |
| J1 | CX90B-16P sehokelo sa USB-C® |
| JP1 | 1 × 15 hlooho ea analoge |
| JP2 | 1 × 15 hlooho ea dijithale |
| U2 | MP2322GQH e fetolelang fatše |
| U3 | GD25B128EWIGR 128 Mbit (16 MB) ext. memori ea khanya |
| DL1 | RGB LED |
| DL2 | LED SCK (serial oache) |
| DL3 | Matla a LED (botala) |
| D2 | Tlhaloso: PMEG6020AELRX Schottky Diode |
| D3 | PRTR5V0U2X,215 Tšireletso ea ESD |
NORA-W106-10B (Radio Module / MCU)
Nano ESP32 e na le mojule oa seea-le-moea o emeng o le mong oa NORA-W106-10B, e kenyang letoto la ESP32-S3 letoto la SoC hammoho le antenna e kentsoeng. ESP32-S3 e ipapisitse le microprocessor ea Xtensa® LX7.
6.1 Xtensa® Dual-Core 32bit LX7 Microprocessor
Microprocessor bakeng sa ESP32-S3 SoC ka hare ho module ea NORA-W106 ke dual-core 32-bit Xtensa® LX7. Mokotla o mong le o mong o ka sebetsa ho fihla ho 240 MHz mme o na le memori ea 512 kB SRAM. LX7 e na le likarolo tse latelang:
- 32-bit sete ea litaelo tse ikhethileng
- 128-bit data bese
- 32-bit multiplier / divider
LX7 e na le 384 kB ROM (Memori e Balang Feela), le 512 kB ea SRAM (Memori ea Phihlello ea Random Static). E boetse e na le memori ea 8 kB RTC FAST le RTC SLOW memori. Likhopotso tsena li etselitsoe ts'ebetso ea matla a tlase, moo mohopolo oa SLOW o ka fihlellehang ke coprocessor ea ULP (Ulta Low Power), e bolokang data ka mokhoa oa boroko bo tebileng.
6.2 Wi-Fi®
Mojule oa NORA-W106-10B o tšehetsa litekanyetso tsa Wi-Fi® 4 IEEE 802.11 b/g/n, ka EIRP e hlahisang matla ho fihlela ho 10 dBm. Boholo ba mojule ona ke limithara tse 500.
- 802.11b: 11 Mbit/s
- 802.11g: 54 Mbit/s
- 802.11n: 72 Mbit/s max ho HT-20 (20 MHz), 150 Mbit/s max ho HT-40 (40 MHz)
6.3 Bluetooth®
Mojule oa NORA-W106-10B o tšehetsa Bluetooth® LE v5.0 ka matla a tlhahiso ea EIRP ho fihla ho 10 dBm le litekanyetso tsa data ho fihla ho 2 Mbps. E na le khetho ea ho hlahloba le ho bapatsa ka nako e le 'ngoe, hammoho le ho tšehetsa likhokahano tse ngata ka mokhoa oa peripheral/central.
6.4 PSRAM
Mojule oa NORA-W106-10B o kenyelletsa 8 MB ea PSRAM e kentsoeng. (Octal SPI)
6.5 Phaello ea Antenna
Antenna e hahelletsoeng mojuleng oa NORA-W106-10B e sebelisa mokhoa oa ho feto-fetoha oa GFSK, ka litekanyetso tsa ts'ebetso tse thathamisitsoeng ka tlase:
Wi-Fi®:
- Matla a hlahisoang a tloaelehileng: 17 dBm.
- Matla a tloaelehileng a hlahisoang ke mahlaseli: 20 dBm EIRP.
- Boikutlo bo etsoang: -97 dBm.
Bluetooth® Matla a Tlase:
- Matla a hlahisoang a tloaelehileng: 7 dBm.
- Matla a tloaelehileng a hlahisoang ke mahlaseli: 10 dBm EIRP.
- Boikutlo bo etsoang: -98 dBm.
Lintlha tsena li nkiloe ho leqephe la data la uBlox NORA-W10 (leqephe la 7, karolo ea 1.5) le fumanehang mona.
Tsamaiso
7.1 Resets
ESP32-S3 e na le tšehetso bakeng sa maemo a mane a reset:
- CPU: tsosolosa CPU0/CPU1 core
- Core: seta sistimi ea dijithale, ntle le lisebelisoa tsa RTC (ULP coprocessor, memori ea RTC).
- Sistimi: e hlophisa sistimi eohle ea dijithale, ho kenyeletsoa le li-peripherals tsa RTC.
- Chip: tsosolosa chip kaofela.
Hoa khoneha ho etsa reset ea software ea boto ena, hammoho le ho fumana lebaka la ho tsosolosa.
Ho etsa reset ea hardware ea boto, sebelisa konopo ea onboard reset (PB1).
Linako tse 7.2
Nano ESP32 e na le li-timers tse latelang:
- 52-bit system timer e nang le 2x 52-bit counters (16 MHz) le 3x comparator.
- 4x li-timers tsa sepheo se akaretsang sa 54-bit
- Li-timers tsa 3x, tse peli ka har'a sistimi e kholo (MWDT0 / 1), e le 'ngoe ho mojule oa RTC (RWDT).
7.3 Ho sitisa
Li-GPIO tsohle tse ho Nano ESP32 li ka hlophisoa hore li sebelisoe joalo ka litšitiso, 'me li fanoa ke matrix a sitisang.
Li-interrupt pins li hlophisitsoe boemong ba kopo, ho sebelisoa litlhophiso tse latelang:
- PHAKOANE
- PHAHAMENG
- FETOHA
- PHAHAMA
- HO TSOHA
Li-protocol tsa puisano tsa serial
Chip ea ESP32-S3 e fana ka phetoho bakeng sa liprothokholo tse fapaneng tsa serial tseo e li tšehetsang. Bakeng sa mohlalaample, bese ea I2C e ka abeloa hoo e batlang e le GPIO efe kapa efe e fumanehang.
8.1 Inter-Integrated Circuit (I2C)
Lithako tsa kamehla:
- A4 - SDA
- A5 – SCL
Bese ea I2C ka ho sa feleng e abeloa lithakhisa tsa A4/A5 (SDA/SCL) bakeng sa ho tsamaellana le retro. Mosebetsi ona oa phini o ka fetoloa, ka lebaka la ho tenyetseha ha chip ea ESP32-S3.
Lithako tsa SDA le SCL li ka abeloa boholo ba li-GPIO, leha ho le joalo tse ling tsa lithakhisa tsena li ka ba le mesebetsi e meng ea bohlokoa e thibelang ts'ebetso ea I2C ho sebetsa ka katleho.
Lemoha ka kopo: lilaebrari tse ngata tsa software li sebelisa mosebetsi o tloaelehileng oa phini (A4/A5).
8.2 Inter-IC Sound (I2S)
Ho na le balaoli ba babeli ba I2S bao hangata ba sebelisetsoang puisano le lisebelisoa tsa molumo. Ha ho na lithakhisa tse khethehileng tse abetsoeng I2S, sena se ka sebelisoa ke GPIO efe kapa efe ea mahala.
Ho sebelisoa mokhoa o tloaelehileng kapa oa TDM, ho sebelisoa mela e latelang:
- MCLK - oache e kholo
- BCLK - oache e nyane
- WS - khetha lentsoe
- DIN/DOUT – serial data
Ho sebelisa mokhoa oa PDM:
- CLK - PDM oache
- Lintlha tsa seriale tsa DIN/DOUT
Bala haholoanyane ka protocol ea I2S ho Espressif's Peripheral API - InterIC Sounds (I2S)
8.3 Sesebelisoa sa Pheripheral Peripheral (SPI)
- SCK – D13
- CIPO – D12
- COPI – D11
- CS – D10
Selaoli sa SPI ka ho sa feleng se abeloa lithakhisa tse ka holimo.
8.4 Universal Asynchronous Receiver/Transmitter (UART)
- D0 / TX
- D1 / RX
Molaoli oa UART ka ho sa feleng o abeloa lithakhisa tse ka holimo.
8.5 Two Wire Automotive Interface (TWAI®)
Molaoli oa CAN / TWAI® o sebelisetsoa ho buisana le mekhoa e sebelisang protocol ea CAN / TWAI®, haholo-holo e tloaelehileng indastering ea likoloi. Ha ho na lithakhisa tse khethehileng tse abetsoeng molaoli oa CAN/TWAI®, GPIO efe kapa efe ea mahala e ka sebelisoa.
Lemoha ka kopo: TWAI® e boetse e tsejoa e le CAN2.0B, kapa "CAN classic". Taolo ea CAN HA e tsamaellane le liforeimi tsa CAN FD.
Memori ea Flash ea kantle
Nano ESP32 e na le 128 Mbit (16 MB) ea lebone la kantle, GD25B128EWIGR (U3). Mohopolo ona o hoketsoe ho ESP32 ka Quad Serial Peripheral Interface (QSPI).
Maqhubu a ts'ebetso ea IC ena ke 133 MHz, 'me e na le sekhahla sa phetisetso ea data ho fihla ho 664 Mbit/s.
Sehokedi sa USB
Nano ESP32 e na le kou e le 'ngoe ea USB-C®, e sebelisetsoang ho matlafatsa le ho hlophisa boto ea hau hammoho le ho romella le ho amohela puisano ea serial.
Hlokomela hore ha ua lokela ho matlafatsa boto ka ho feta 5 V ka boema-kepe ba USB-C®.
Likhetho tsa Matla
Matla a ka fanoa ka phini ea VIN, kapa ka sehokelo sa USB-C®. Molumo ofe kapa ofetage input e ka ba ka USB kapa VIN e theoleloa ho 3.3 V ho sebelisoa converter ea MP2322GQH (U2).
Karolo ea ts'ebetsotage bakeng sa boto ena ke 3.3 V. Ka kopo hlokomela hore ha ho na pin ea 5V e fumanehang botong ena, feela VBUS e ka fana ka 5 V ha boto e tsamaisoa ka USB.
11.1 Sefate sa Matla
11.2 Pin Moqtage
Lipini tsohle tsa dijithale le tsa analog ho Nano ESP32 ke 3.3 V. Se ke oa hokela matla a phahamengtage lisebelisoa ho efe kapa efe ea lithakhisa kaha e tla ipeha kotsing ea ho senya boto.
11.3 Litekanyo tsa VIN
Kenyeletso e khothaletsoang voltagboholo ba eona ke 6-21 V.
Ha ua lokela ho leka ho matlafatsa boto ka voltage ka ntle ho sebaka se khothalletsoang, haholo-holo eseng holimo ho 21 V.
Matla a converter a ipapisitse le matla a ho kenya letsohotage ka pina ea VIN. Sheba karolelano e ka tlase bakeng sa ts'ebetso ea boto e nang le tšebeliso e tloaelehileng ea hajoale:
- 4.5 V -> 90%.
- 12 V - 85-90%
- 18 V - <85%
Tlhahisoleseding ena e ntšitsoe ho database ea MP2322GQH.
11.4 VBUS
Ha ho na phini ea 5V e fumanehang ho Nano ESP32. 5 V e ka fanoa feela ka VBUS, e fanoang ka kotloloho ho tsoa mohloling oa matla oa USB-C®.
Ha o ntse o matlafatsa boto ka phini ea VIN, phini ea VBUS ha e sebetse. Sena se bolela hore ha o na boikhethelo ba ho fana ka 5 V ho tsoa boto ntle le haeba o sebelisoa ka USB kapa kantle.
11.5 Ho sebelisa 3.3 V Pin
Pini ea 3.3 V e hokahane le terene ea 3.3 V e hokahaneng le tlhahiso ea MP2322GQH ea ho theola converter. Pini ena e sebelisoa haholo ho matlafatsa likarolo tsa kantle.
11.6 Pin ea Hona Joale
Li-GPIO tse ho Nano ESP32 li khona ho sebetsana le maqhubu a mohloli ho fihla ho 40 mA, le ho tebela maqhubu ho fihlela ho 28 mA. Le ka mohla u se ke ua hokahanya lisebelisoa tse hulelang morao-rao ka kotloloho ho GPIO.
Boitsebiso ba Mechini
Pinout
12.1 Analog (JP1)
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D13 / SCK | NC | Seriba oache |
| 2 | +3V3 | Matla | +3V3 Seporo sa Matla |
| 3 | BOTSOA0 | Mokhoa | Reset Boto 0 |
| 4 | A0 | Analoge | Ho kenya Analog 0 |
| 5 | A1 | Analoge | Ho kenya Analog 1 |
| 6 | A2 | Analoge | Ho kenya Analog 2 |
| 7 | A3 | Analoge | Ho kenya Analog 3 |
| 8 | A4 | Analoge | Kenyelletso ea Analog 4 / I²C Serial Data (SDA) |
| 9 | A5 | Analoge | Kenyelletso ea Analog 5 / I²C Serial Clock (SCL) |
| 10 | A6 | Analoge | Ho kenya Analog 6 |
| 11 | A7 | Analoge | Ho kenya Analog 7 |
| 12 | V-BUS | Matla | Matla a USB (5V) |
| 13 | BOTSOA1 | Mokhoa | Reset Boto 1 |
| 14 | GND | Matla | Fatše |
| 15 | VIN | Matla | MoqtagKeletso |
12.2 Digital (JP2)
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D12 / CIPO* | Dijithale | Controller In Peripheral Out |
| 2 | D11 / COPI* | Dijithale | Controller Out Peripheral In |
| 3 | D10 / CS* | Dijithale | Chip Khetha |
| 4 | D9 | Dijithale | Digital pin 9 |
| 5 | D8 | Dijithale | Digital pin 8 |
| 6 | D7 | Dijithale | Digital pin 7 |
| 7 | D6 | Dijithale | Digital pin 6 |
| 8 | D5 | Dijithale | Digital pin 5 |
| 9 | D4 | Dijithale | Digital pin 4 |
| 10 | D3 | Dijithale | Digital pin 3 |
| 11 | D2 | Dijithale | Digital pin 2 |
| 12 | GND | Matla | Fatše |
| 13 | RST | Ka hare | Seta bocha |
| 14 | D1/RX | Dijithale | Digital pin 1 / Serial Receiver (RX) |
| 15 | D0/TX | Dijithale | Digital pin 0 / Serial Transmitter (TX) |
*CIPO/COPI/CS e nkela sebaka sa mantsoe a MISO/MOSI/SS.
Ho Beha Likoti le Kemiso ea Boto
Ts'ebetso ea Boto
14.1 Ho qala – IDE
Haeba u batla ho hlophisa Nano ESP32 ea hau ha u sa sebetse u hloka ho kenya Arduino IDE [1]. Ho hokela Nano ESP32 komporong ea hau, o tla hloka thapo ea USB ea Type-C®, e ka fanang ka matla ho boto, joalo ka ha ho bonts'itsoe ke LED (DL1).
14.2 Ho qala – Arduino Web Mohlophisi
Liboto tsohle tsa Arduino, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose la Arduino Web Mohlophisi [2], ka ho kenya plugin e bonolo feela.
Arduino Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau.
14.3 Ho qala - Arduino Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino IoT li tšehetsoa ho Arduino Cloud e u lumellang hore u kene, u hlahlobe le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
14.4 Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho Arduino Project Hub [4], Arduino Library Reference [5], le lebenkele la inthanete [6] ]; moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling.
14.5 Pholiso ea Boto
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho khantša boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khonahala ho kenya mokhoa oa bootloader ka ho tlanya konopo ea reset hang ka mor'a ho tima.
Setifikeiti
Declaration of Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
Phatlalatso ea Tumellano le EU RoHS & REACH 211
01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Maximum Limit (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokollo : Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse hore ha ho le e 'ngoe ea li-SVHC https://echa.europa.eu/web/guest/candidate-list-table), Lethathamo la Bakhethoa ba Matšoenyeho a Holimo Haholo bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoang tsohle (le sephutheloana) ka bongata bo boholo bo lekanang kapa bo kaholimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha e boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa lisebelisoa tsa elektroniki le tsa motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e amanang le Conflict Minerals, haholoholo Dodd-Frank Wall Street Reform and Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise kapa ha e sebetsane le likhohlano ka kotloloho. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tse loantšanang li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ba ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho ipapisitsoe le tlhaiso-leseling eo re e fumaneng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Conflict tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Sesebelisoa sena se lokela ho kengoa le ho sebetsoa ka bonyane ba 20 cm lipakeng tsa radiator le 'mele oa hau.
Hlokomela: Thepa ena e lekoa 'me e fumanoe e lumellana le meeli ea sesebelisoa sa digital sa Sehlopha sa B, ho latela karolo ea 15 ea Melao ea FCC. Meeli ena e etselitsoe ho fana ka tšireletso e utloahalang khahlanong le tšitiso e kotsi mohahong oa bolulo. Thepa ena e hlahisa, e sebelisa le ho khantša matla a maqhubu a seea-le-moea, 'me haeba e sa kengoa le ho sebelisoa ho latela litaelo, e ka baka tšitiso e kotsi likhokahanong tsa radio. Leha ho le joalo, ha ho na tiiso ea hore tšitiso e ke ke ea etsahala setsing se itseng. Haeba sesebelisoa sena se baka tšitiso e kotsi ea seea-le-moea kapa kamohelo ea thelevishene, e ka khethoang ka ho tima le ho tima sesebelisoa, mosebelisi o khothaletsoa ho leka ho lokisa tšitiso ka e le 'ngoe kapa ho feta tsa mehato e latelang:
- Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
- Eketsa karohano pakeng tsa thepa le moamoheli.
- Hokela lisebelisoa ho seketjana se fapaneng le seo moamoheli a hoketsoeng ho sona.
- Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.
Libukana tsa mosebelisi bakeng sa lisebelisoa tsa radio tse se nang laesense li tla ba le tsebiso e latelang kapa e lekanang le eona sebakeng se hlakileng bukeng ea mosebelisi kapa ka mokhoa o mong sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa laesense tsa Industry Canada tse sa kgetheng RSS. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Thempereichara ea ho sebetsa ea EUT e ke ke ea feta 85 ℃ 'me ha ea lokela ho ba ka tlase ho -40 ℃.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 201453/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino Srl |
| Aterese ea Khampani | Via Andrea Appiani, 25 Monza, MB, 20900 Italy |
Litokomane Tsa Litšupiso
| Ref | Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino Web Mohlophisi (Leru) | https://create.arduino.cc/editor |
| Web Mohlophisi - Ho qala | https://docs.arduino.cc/cloud/web-editor/tutorials/getting-started/getting-started-web-editor |
| Morero Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://github.com/arduino-libraries/ |
| Online Store | https://store.arduino.cc/ |
Fetola Log
| Letsatsi | Liphetoho |
| 08/06/2023 | Lokolla |
| 09/01/2023 | Ntlafatsa tatellano ea sefate sa motlakase. |
| 09/11/2023 | Ntlafatsa karolo ea SPI, ntlafatsa karolo ea analog/digital pin. |
| 11/06/2023 | Lebitso le nepahetseng la k'hamphani, VBUS/VUSB e nepahetseng |
| 11/09/2023 | Block Diagram Update, Litlhaloso tsa Antenna |
| 11/15/2023 | Ntlafatso ea mocheso oa tikoloho |
| 11/23/2023 | E kentse label ho mekhoa ea LP |
E fetotsoe: 29/01/2024
Litokomane / Lisebelisoa
 |
Arduino Nano ESP32 e nang le Lihlooho [pdf] Bukana ea Mosebelisi Nano ESP32 e nang le Lihlooho, Nano, ESP32 e nang le Lihlooho, ka Lihlooho, Lihlooho |