ARDUINO AKX00034 Edge Control Owner's
Tlhaloso
Boto ea Arduino® Edge Control e etselitsoe ho sebetsana le litlhoko tsa temo e nepahetseng. E fana ka tsamaiso e tlaase ea matla, e loketseng ho nosetsa ka khokahanyo ea modular. Ts'ebetso ea boto ena e atolosoa ka Arduino® MKR Boards ho fana ka khokahanyo e eketsehileng.
Libaka tse reriloeng
Litekanyo tsa temo, mekhoa e bohlale ea ho nosetsa, hydroponics
Likaroloana
Tlhaloso: Nina B306 module
processor
- 64 MHz Arm® Cortex®-M4F (ka FPU)
- 1 MB Flash + 256 KB RAM
Wireless
- Bluetooth (BLE 5 ka Cordio® stack) Advertising Extensions
- 95dBm kutloisiso
- 4.8 mA ho TX (0 dBm)
- 4.6 mA ho RX (1 Mbps)
Pheripherals
- Lebelo le felletseng la 12 Mbps USB
- Arm® CryptoCell® CC310 ts'ireletso ea subsystem QSPI/SPI/TWI/I²S/PDM/QDEC
- Lebelo le phahameng 32 MHz SPI
- Quad SPI interface 32 MHz
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR co-processor
Mohopolo
- 1 MB memori ea ka hare ea Flash
- 2MB ka har'a QSPI
- Slot Card ea SD
Matla
- Matla a Tlase
- 200uA Boroko ba hona joale
- E ka sebetsa ho fihlela likhoeli tse 34 ka betri ea 12V/5Ah
- Phepelo ea Battery ea 12 V Acid/lead SLA (E nchafalitsoe ka liphanele tsa letsatsi) RTC CR2032 Lithium Battery bekapo
Betri
- LT3652 Solar Panel Battery Charger
- Input Supply Voltage Regulation Loop for Peak Power Tracking in (MPPT) Lisebelisoa tsa Solar
I/O
- Lithapa tsa ho tsoha tse 6x tse utloang bohloko
- 16x hydrostatic watermark sensor input
- 8x 0-5V lisebelisoa tsa analoge
- 4x 4-20mA lisebelisoa
- Liphetho tsa taelo ea 8x latching relay le bakhanni
- Liphetho tsa taelo ea 8x latching relay ntle le bakhanni
- 4x 60V/2.5A li-relays tsa boemo bo tiileng bo arohaneng ka galvanically
- 6x 18 pin plug ho lihokelo tsa li-terminal block
Socket ea MKR e 'meli
- Taolo ea matla ea motho ka mong
- Motho ka mong Serial Port
- Likou tsa I2C tsa motho ka mong
Lintlha tsa polokeho
- Sehlopha sa A
Boto
Kopo Examples
Arduino® Edge Control ke tsela ea hau ea ho ea Temo 4.0. Fumana temohisiso ea nako ea 'nete mabapi le boemo ba ts'ebetso ea hau le ho eketsa chai ea lijalo. Ntlafatsa ts'ebetso ea khoebo ka ho iketsetsa le ho lema esale pele. Etsa hore Taolo ea Edge e lumellane le litlhoko tsa hau ka ho sebelisa Liboto tse peli tsa Arduino® MKR le mefuta e mengata ea Lithebe tse tsamaellanang. Boloka lirekoto tsa nalane, taolo ea boleng ka bohona, kenya tšebetsong moralo oa lijalo, le tse ling ka Arduino IoT Cloud ho tsoa kae kapa kae lefatšeng.
Li-Greenhouses tse ikemetseng
Bakeng sa ho fokotsa tlhahiso ea khabone le ho eketsa chai ea moruo, ho bohlokoa ho netefatsa hore ho fanoa ka tikoloho e ntlehali bakeng sa kholo ea lijalo ho latela mongobo, mocheso le lintlha tse ling. Arduino® Edge Control ke sethala se kopaneng se nolofalletsang ho lekola hole le ho ntlafatsa nako ea nnete ho fihlela sena. Ho kenyeletsoa Arduino® MKR GPS Shield (SKU: ASX00017) e lumella moralo o nepahetseng oa ho potoloha ha lijalo le ho fumanoa ha data ea geospatial.
Hydroponics / Aquaponics
Kaha hydroponics e kenyelletsa ho hola ha limela ntle le mobu, tlhokomelo e hlokolosi e tlameha ho bolokoa ho netefatsa hore li boloka fensetere e moqotetsane e hlokahalang bakeng sa kholo e ntle. The Arduino Edge Control e ka etsa bonnete ba hore fensetere ena e finyelloa ka mosebetsi o fokolang oa matsoho. Aquaponics e ka fana ka melemo e mengata ho feta hydroponics e tloaelehileng eo Arduino®'s Edge Control e ka thusang ho tsamaisana le litlhoko tse phahameng le ho feta ka ho fana ka taolo e betere holim'a ts'ebetso ea kahare ha qetellong e fokotsa likotsi tsa tlhahiso.
Temo ea Li-mushroom: Li-mushroom li tumme ka ho hloka maemo a mocheso le mongobo o phethahetseng ho ts'ehetsa kholo ea spores ha li ntse li thibela li-fungus tse hlolisanang ho hola. Ka lebaka la li-sensorer tse ngata tsa watermark, likou tsa lihlahisoa, le likhetho tsa khokahanyo tse fumanehang ho Arduino® Edge Control hammoho le Arduino® IoT Cloud, temo ena e nepahetseng e ka finyelloa ka tsela e e-so ka e bonoa.
Lisebelisoa.
- Tensiometers ea thermometer
- Li-sensor tsa mongobo oa mobu oa watermark
- Li-valve tsa bolo tse entsoeng ka mechine
- Phanele ea letsatsi
- 12V/5Ah asiti/lead SLA betri (11 – 13.3V)
Lihlahisoa tse Amanang
- LCD Display + Flat Cable + polasetiki e koaletsoeng
- 1844646 mabitso a Phoenix (a kenyelelitsoe le sehlahisoa)
- Arduino® MKR family boards (bakeng sa ho holisa khokahanyo e se nang mohala)
Tharollo e Felileview
Example ea kopo e tloaelehileng ea tharollo ho kenyeletsoa LCD Display le liboto tse peli tsa Arduino® MKR 1300.
Lintlha
Feletseng Maximum Ratings
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| TMax | Boholo ba tekanyo ea mocheso | -40 | 20 | 85 | °C |
| VBattMax | Boholo ba ho kenya voltage ho tsoa ho ho kenya betri | -0.3 | 12 | 17 | V |
| VSolarMax | Boholo ba ho kenya voltage ho tloha ho solar panel | -20 | 18 | 20 | V |
| ARelayMax | Boholo ba hona joale ka sesebelisoa sa relay | – | – | 2.4 | A |
| PMax | Tšebeliso e Felletseng ea Matla | – | – | 5000 | mW |
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| T | Meeli ea mocheso oa Conservative | -15 | 20 | 60 | °C |
| VBatt | Keletso voltage ho tsoa ho ho kenya betri | – | 12 | – | V |
| VSolar | Keletso voltage ho tloha ho solar panel | 16 | 18 | 20 | V |
E sebetsa hapeview
Board Topology
Holimo View
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U1 | LT3652HV betri ea tjhaja IC | J3,7,9,8,10,11 | Li-terminals tse 1844798 tse ka khonang |
| U2 | MP2322 3.3V converter buck IC | LED1 | Ka board LED |
| U3 | MP1542 19V e matlafatsang converter IC | PB1 | Seta konopo ea konopo hape |
| U4 | TPS54620 5V e matlafatsang converter IC | J6 | Karete ea Micro SD |
| U5 | CD4081BNSR LE heke IC | J4 | Sesebelisoa sa betri sa CR2032 |
| U6 | CD40106BNSR HASE heke ea IC | J5 | Micro USB (NINA Module) |
| U12,U17 | MC14067BDWG multiplexer IC | U8 | Tlhaloso: TCA6424A IO expander IC |
| U16 | CD40109BNSRG4 I/O Expander | U9 | Setšoantšo sa NINA-B306 |
| U18,19,20,21 | TS13102 boemo bo tiileng ba relay IC | U10 | Tlhaloso: ADR360AUJZ-R2 Voltage referense letoto la lihlooho tse 2.048V IC |
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U11 | Tlhaloso: W25Q16JVZPIQ Flash 16M IC | Q3 | ZXMP4A16GTA MOSFET P-CH 40V 6.4A |
| U7 | CD4081BNSR LE heke IC | U14, 15 | Setšoantšo sa MC14067BDWG IC MUX |
processor
Main processor ke Cortex M4F e sebetsang ho fihla ho 64MHz.
LCD skrine
Arduino® Edge Control e fana ka sehokelo se inehetseng (J1) bakeng sa ho hokahanya le HD44780 16 × 2 LCD module ea pontšo, e rekisoang ka thoko. Motlakase o ka sehloohong o laola LCD ka TCA6424 port expander holim'a I2C. Lintlha li fetisoa ka sebopeho sa 4-bit. LCD backlight intensity e boetse e fetoloa ke processor e kholo.
Li-Sensors tsa Analog tsa 5V
Ho fihla ho tse robeli tsa li-analoge tsa 0-5V li ka hokeloa ho J4 bakeng sa li-sensor tsa analog tse hokahantsoeng joalo ka li-tensiometer le li-dendrometer. Lintho tse kenang li sirelelitsoe ke 19V Zener diode. Kenyelletso e 'ngoe le e' ngoe e hokahane le analog multiplexer e tsamaisang lets'oao ho boema-kepe bo le bong ba ADC. Kenyelletso ka 'ngoe e hokahane le analog multiplexer (MC14067) e tsamaisang lets'oao ho boema-kepe bo le bong ba ADC. Mochine o ka sehloohong o laola khetho ea ho kenya ka mochine oa TCA6424 port expander holim'a I2C.
Li-sensor tsa 4-20mA
Ho fihla ho li-sensor tse 'ne tsa 4-20mA li ka hokela ho J4. Moqtage ea 19V e hlahisoa ke MP1542 step-up converter ho matlafatsa lupu ea hona joale. Boleng ba sensor bo baloa ka 220 ohm resistor. Kenyelletso ka 'ngoe e hokahane le analog multiplexer (MC14067) e tsamaisang lets'oao ho boema-kepe bo le bong ba ADC. Mochine o ka sehloohong o laola khetho ea ho kenya ka mochine oa TCA6424 port expander holim'a I2C.
Li-Sensors tsa Watermark
Ho fihla ho lisensara tse leshome le metso e tšeletseng tsa hydrostatic watermark li ka hokeloa ho J8. Lipini J8-17 le J8-18 ke li-sensor pins tse tloaelehileng bakeng sa li-sensor tsohle, tse laoloang ka kotloloho ke microcontroller. Lintho tse kenang le li-sensor pins tse tloaelehileng li sirelelitsoe ke diode ea 19V Zener. Kenyelletso ka 'ngoe e hokahane le analog multiplexer (MC14067) e tsamaisang lets'oao ho boema-kepe bo le bong ba ADC. Mochine o ka sehloohong o laola khetho ea ho kenya ka mochine oa TCA6424 port expander holim'a I2C. Boto e tšehetsa mekhoa e 2 e nepahetseng.
Latching Outputs
Lihokelo J9 le J10 li fana ka liphetho ho lisebelisoa tsa latching joalo ka li-valve tsa enjene. Sehlahisoa sa latching se na le likanale tse peli (P le N) tseo ka tsona ho ka romelloang tšusumetso kapa strobe ho e 'ngoe ea likanale tse peli (ho bula valve e koalang bakeng sa ex.ample). Nako ea li-strobes e ka hlophisoa ho ikamahanya le tlhokahalo ea sesebelisoa sa kantle. Boto e fana ka kakaretso ea likou tse 16 tse arotsoeng ka mefuta e 'meli:
- Litaelo tsa Latching (J10): Likou tse 8 tsa lisebelisoa tse phahameng tsa impedance (max +/- 25 mA). Hokela ho lisebelisoa tsa kantle tse nang le ts'ireletso ea motho oa boraro / li-circuits tsa motlakase. Ho buuoa ka VBAT.
- Latching Out (J9): 8 likoung. Liphetho tsena li kenyelletsa bakhanni ba sesebelisoa sa latching. Ha ho hlokahale bakhanni ba kantle. Ho buuoa ka VBAT.
Li-Relay tsa Naha tse Tiileng
Boto e na le li-relay tse 'ne tse ka lokisoang tsa 60V 2.5A tse nang le karohano ea galvanic e fumanehang ho J11. Lisebelisoa tse tloaelehileng li kenyelletsa HVAC, taolo ea ho fafatsa jj.
Polokelo
Boto e kenyelletsa sokete ea karete ea MicroSD le memori e eketsehileng ea 2MB bakeng sa polokelo ea data. Ka bobeli li hokahane ka kotloloho le processor ea mantlha ka sebopeho sa SPI.
Sefate sa Matla
Boto e ka tsamaisoa ka liphanele tsa letsatsi le/kapa libeteri tsa SLA.
Ts'ebetso ea Boto
Ho qala - IDE
Haeba u batla ho hlophisa Arduino® Edge Control ha u ntse u le sieo, u lokela ho kenya Arduino® Desktop IDE [1] Ho hokela taolo ea Arduino® Edge komporong ea hau, u tla hloka thapo ea USB ea Micro-B. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
Ho qala - Arduino Web Mohlophisi
Liboto tsohle tsa Arduino®, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose la Arduino® Web Mohlophisi [2], ka ho kenya plugin e bonolo feela. Arduino® Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau.
Ho qala - Arduino IoT Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino® IoT li tšehetsoa ho Arduino® IoT Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
Sample Sketches
Sample sketches bakeng sa Arduino® Edge Control e ka fumanoa ho "Examples" ho Arduino® IDE kapa karolong ea "Documentation" ea Arduino® Pro. websebaka [4]
Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho ProjectHub [5], Arduino® Library Reference [6] le lebenkele la marang-rang [7] moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling.
Boto ea Pholiso
Liboto tsohle tsa Arduino® li na le bootloader e hahelletsoeng kahare e lumellang ho khantša boto ka USB. Haeba sketch e notlela processor mme boto e se e sa fihlellehe ka USB, hoa khoneha ho kenya mokhoa oa bootloader ka ho tlanya habeli konopo ea reset hang ka mor'a hore motlakase o theohe.
Sehokedi Pinouts
J1 LCD Sehokelo
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | PWM | Matla | Backlight LED Cathode (taolo ea PWM) |
| 2 | Matla On | Dijithale | Kenya konopo |
| 3 | +5V LCD | Matla | Motlakase oa LCD |
| 4 | LCD RS | Dijithale | Letšoao la LCD RS |
| 5 | Bapisa | Analoge | Taolo ea Phapano ea LCD |
| 6 | LCD RW | Dijithale | Letšoao la LCD Bala/Ngola |
| 7 | LED + | Matla | Backlight LED Anode |
| 8 | LCD EN | Dijithale | LCD E nolofalletsa lets'oao |
| 10 | LCD D4 | Dijithale | Letšoao la LCD D4 |
| 12 | LCD D5 | Dijithale | Letšoao la LCD D5 |
| 14 | LCD D6 | Dijithale | Letšoao la LCD D6 |
| 16 | LCD D7 | Dijithale | Letšoao la LCD D7 |
| 9,11,13,15 | GND | Matla | Fatše |
Lipontšo tsa ho tsoha tsa J3 / Litaelo tsa Kantle tsa Relay
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1,3,5,7,9 | V BATHO | Matla | Gated voltage betri bakeng sa referense ea lets'oao la ho tsoha |
| 2,4,6,8,10,12 | Kenyeletso | Dijithale | Matshwao a ho tsoha a hlokolosi |
| 13 | Sephetho | Dijithale | Letšoao la oache ea kantle e tiileng ea boemo bo 1 |
| 14 | Sephetho | Dijithale | Letšoao la oache ea kantle e tiileng ea boemo bo 2 |
| 17 | Bidir | Dijithale | Letšoao la data la kantle le tiileng la boemo bo 1 |
| 18 | Bidir | Dijithale | Letšoao la data la kantle le tiileng la boemo bo 2 |
| 15,16 | GND | Matla | Fatše |
J5 USB
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | VUSB | Matla | Tlhokomeliso ea Kenyelletso ea Matla: Boto e tsamaisoang feela ka V USB e ke ke ea lumella boholo ba likarolo tsa boto. Sheba sefate sa matla ho Karolo ea 3.8 |
| 2 | D- | Tse fapaneng | Lintlha tse fapaneng tsa USB - |
| 3 | D+ | Tse fapaneng | Lintlha tse fapaneng tsa USB + |
| 4 | ID | NC | E sa sebelisoeng |
| 5 | GND | Matla | Fatše |
J7 Analog/4-20mA
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1,3,5,7 | +19V | Matla | 4-20mA voltage referense |
| 2 | IN1 | Analoge | 4-20mA ho kenya 1 |
| 4 | IN2 | Analoge | 4-20mA ho kenya 2 |
| 6 | IN3 | Analoge | 4-20mA ho kenya 3 |
| 8 | IN4 | Analoge | 4-20mA ho kenya 4 |
| 9 | GND | Matla | Fatše |
| 10 | +5V | Matla | 5V e hlahisoang bakeng sa referense ea analoge ea 0-5V |
| 11 | A5 | Analoge | 0-5V tlhahiso 5 |
| 12 | A1 | Analoge | 0-5V tlhahiso 1 |
| 13 | A6 | Analoge | 0-5V tlhahiso 6 |
| 14 | A2 | Analoge | 0-5V tlhahiso 2 |
| 15 | A7 | Analoge | 0-5V tlhahiso 7 |
| 16 | A3 | Analoge | 0-5V tlhahiso 3 |
| 17 | A8 | Analoge | 0-5V tlhahiso 8 |
| 18 | A4 | Analoge | 0-5V tlhahiso 4 |
J8 Watermark
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | MetsiMrk1 | Analoge | Tlhahiso ea watermark 1 |
| 2 | MetsiMrk2 | Analoge | Tlhahiso ea watermark 2 |
| 3 | MetsiMrk3 | Analoge | Tlhahiso ea watermark 3 |
| 4 | MetsiMrk4 | Analoge | Tlhahiso ea watermark 4 |
| 5 | MetsiMrk5 | Analoge | Tlhahiso ea watermark 5 |
| 6 | MetsiMrk6 | Analoge | Tlhahiso ea watermark 6 |
| 7 | MetsiMrk7 | Analoge | Tlhahiso ea watermark 7 |
| 8 | MetsiMrk8 | Analoge | Tlhahiso ea watermark 8 |
| 9 | MetsiMrk9 | Analoge | Tlhahiso ea watermark 9 |
| 10 | MetsiMrk10 | Analoge | Tlhahiso ea watermark 10 |
| 11 | MetsiMrk11 | Analoge | Tlhahiso ea watermark 11 |
| 12 | MetsiMrk12 | Analoge | Tlhahiso ea watermark 12 |
| 13 | MetsiMrk13 | Analoge | Tlhahiso ea watermark 13 |
| 14 | MetsiMrk14 | Analoge | Tlhahiso ea watermark 14 |
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 15 | MetsiMrk15 | Analoge | Tlhahiso ea watermark 15 |
| 16 | MetsiMrk16 | Analoge | Tlhahiso ea watermark 16 |
| 17,18 | TSOHLE | Dijithale | Sensor e tloaelehileng voltage |
J9 Latching Out (+/- VBAT)
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | PULSE_OUT0_P | Dijithale | Latching tlhahiso 1 positive |
| 2 | PULSE_OUT0_N | Dijithale | Latching tlhahiso 1 negative |
| 3 | PULSE_OUT1_P | Dijithale | Latching tlhahiso 2 positive |
| 4 | PULSE_OUT1_N | Dijithale | Latching tlhahiso 2 negative |
| 5 | PULSE_OUT2_P | Dijithale | Latching tlhahiso 3 positive |
| 6 | PULSE_OUT2_N | Dijithale | Latching tlhahiso 3 negative |
| 7 | PULSE_OUT3_P | Dijithale | Latching tlhahiso 4 positive |
| 8 | PULSE_OUT3_N | Dijithale | Latching tlhahiso 4 negative |
| 9 | PULSE_OUT4_P | Dijithale | Latching tlhahiso 5 positive |
| 10 | PULSE_OUT4_N | Dijithale | Latching tlhahiso 5 negative |
| 11 | PULSE_OUT5_P | Dijithale | Latching tlhahiso 6 positive |
| 12 | PULSE_OUT5_N | Dijithale | Latching tlhahiso 6 negative |
| 13 | PULSE_OUT6_P | Dijithale | Latching tlhahiso 7 positive |
| 14 | PULSE_OUT6_N | Dijithale | Latching tlhahiso 7 negative |
| 15 | PULSE_OUT7_P | Dijithale | Latching tlhahiso 8 positive |
| 16 | PULSE_OUT7_N | Dijithale | Latching tlhahiso 8 negative |
| 17,18 | GND | Matla | Fatše |
J10 Latching Command (+/- VBAT)
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | STOBE8_P | Dijithale | Latching taelo 1 positive |
| 2 | STOBE8_N | Dijithale | Latching taelo 1 negative |
| 3 | STOBE9_P | Dijithale | Latching taelo 2 positive |
| 4 | STOBE9_N | Dijithale | Latching taelo 2 negative |
| 5 | STOBE10_P | Dijithale | Latching taelo 3 positive |
| 6 | STOBE10_N | Dijithale | Latching taelo 3 negative |
| 7 | STOBE11_P | Dijithale | Latching taelo 4 positive |
| 8 | STOBE11_N | Dijithale | Latching taelo 4 negative |
| 9 | STOBE12_N | Dijithale | Latching taelo 5 positive |
| 10 | STOBE12_P | Dijithale | Latching taelo 5 negative |
| 11 | STOBE13_P | Dijithale | Latching taelo 6 positive |
| 12 | STOBE13_N | Dijithale | Latching taelo 6 negative |
| 13 | STOBE14_P | Dijithale | Latching taelo 7 positive |
| 14 | STOBE14_N | Dijithale | Latching taelo 7 negative |
| 15 | STOBE15_P | Dijithale | Latching taelo 8 positive |
| 16 | STOBE15_N | Dijithale | Latching taelo 8 negative |
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 17 | GATED_VBAT_PULSE | Matla | Gated Positive terminal ea betri |
| 18 | GND | Matla | Fatše |
J11 Relay (+/- VBAT)
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | SOLAR+ | Matla | Solar Panel Positive Terminal |
| 2 | NC | NC | E sa sebelisoeng |
| 3 | GND | Matla | Fatše |
| 4 | RELAY1_P | Fetoha | Relay 1 positive |
| 5 | NC | NC | E sa sebelisoeng |
| 6 | RELAY1_N | Fetoha | Relay 1 negative |
| 7 | NC | NC | E sa sebelisoeng |
| 8 | RELAY2_P | Fetoha | Relay 2 positive |
| 9 | NC | NC | E sa sebelisoeng |
| 10 | RELAY2_N | Fetoha | Relay 2 negative |
| 11 | 10kGND | Matla | Sebaka sa fatše ka 10k resistor |
| 12 | RELAY3_P | Fetoha | Relay 3 positive |
| 13 | NTC | Analoge | Thermoresistor e nang le mocheso o tlase oa mocheso o tlase oa NTC |
| 14 | RELAY3_N | Fetoha | Relay 3 negative |
| 15 | GND | Matla | Fatše |
| 16 | RELAY4_P | Fetoha | Relay 4 positive |
| 17 | BATHO+ | Matla | Theminale ea Battery Positive |
| 18 | RELAY4_N | Fetoha | Relay 4 negative |
Boitsebiso ba Mechini
Kemiso ea Boto
Mount Holes
Maemo a Mohokahanyi
Setifikeiti
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Maximum Limit (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokoloho : Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse leha e le efe ea SVHCs (https://echa.europa.eu/web/moeti/lethathamo la mokhethoa), Lethathamo la Bakhethoa ba Matšoenyeho a Phahameng ka ho Fetisisa bakeng sa tumello e lokollotsoeng ke ECHA, le teng lihlahisoa tsohle (le sephutheloana) ka bongata bo lekanang le mahloriso a lekanang kapa a ka holimo ho 0.1%. Ho ea ka tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete leha e le efe ea bohlokoa joalokaha e boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa lisebelisoa tsa elektroniki le tsa motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e amanang le Conflict Minerals, haholoholo Dodd-Frank Wall Street Reform and Consumer Protection Act, Karolo ea 1502. Arduino ha e hlahise kapa ha e sebetsane le likhohlano ka kotloloho. liminerale tse kang Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tse loantšanang li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ba ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melao. Ho ipapisitsoe le tlhaiso-leseling eo re e fumaneng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Conflict tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Thepa ena e lokela ho kengoa le ho sebetsoa ka sebaka sa bonyane 20cm lipakeng tsa radiator le 'mele oa hau.
Sesotho: Libukana tsa mosebelisi bakeng sa lisebelisoa tsa radio tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang sebakeng se hlakileng bukeng ea mosebelisi kapa sesebelisoa kapa ka bobeli. Sesebediswa sena se dumellana le ditekanyetso tsa RSS tse sa dumelleng laesense ya Industry Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR
Sesotho Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Thempereichara ea ts'ebetso ea EUT e ke ke ea feta 85 ℃ mme ha ea lokela ho ba ka tlase ho -40 ℃.
| Maqhubu a maqhubu | Matla a phahameng haholo (ERP) |
| 2402-2480Mhz | 3.35dBm |
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 201453/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino Srl |
| Aterese ea Khampani | Via Andrea Appiani 25, 20900 Monza, Italy |
Litokomane Tsa Litšupiso
| Ref | Sehokelo |
| Arduino® IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino® IDE (Leru) | https://create.arduino.cc/editor |
| Arduino® Cloud IDE Ho qala | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-editor-4b3e4a |
| Arduino® Pro Websebaka | https://www.arduino.cc/pro |
| Morero Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Reference Library | https://github.com/bcmi- labs/Arduino_EdgeControl/tree/4dad0d95e93327841046c1ef80bd8b882614eac8 |
| Online Store | https://store.arduino.cc/ |
Fetola log
| Letsatsi | Khatiso | Liphetoho |
| 21/02/2020 | 1 | Phatlalatso ea Pele |
| 04/05/2021 | 2 | Ntlafatso ea moralo / sebopeho |
| 30/12/2021 | 3 | Lintlafatso tsa litaba |
Litokomane / Lisebelisoa
 |
ARDUINO AKX00034 Edge Control [pdf] Buka ea Mong'a AKX00034, 2AN9S-AKX00034, 2AN9SAKX00034, AKX00034 Edge Control, Edge Control |
