Litlhaloso:
- Likonopo: K6 - 6 programmable, K8 - 8 programmable, K15 - 15 programmable
- Backlight: RGB e nang le khetho ea Dimming
- Khokahano: AiM CAN ka 5 Pins Binder 712 sehokelo sa basali
- Boitsebiso ba 'mele: Silicon ea rabara le PA6 GS30% e matlafalitsoeng
- Litekanyo: K6 - 97.4x71x4x24mm, K8 - 127.4×71.4x24mm, K15 - 157.4×104.4x24mm
- Boima ba 'mele: K6 - 120g, K8 - 150g, K15 - 250g
- Ha e kenelle metsi: IP67
Litaelo tsa Tšebeliso ea Sehlahisoa
Ho hokela Keypad:
Hokela Keypad ho AiM PDM08 kapa PDM32 u sebelisa thapo e fanoeng ea CAN. Netefatsa hore khokahano e bolokehileng e entsoe.
Ho lokisa li-buttons:
Sebelisa AiM RaceStudio 3 Software ho hlophisa konopo ka 'ngoe ho Keypad ho latela khetho ea hau. Likonopo li ka hlophisoa e le tsa Momentary kapa Multi-Status.
Ho seta mekhoa ea likonopo:
- Nakoana: Kopanya taelo ho konopo e 'ngoe le e' ngoe. E hloka Pontšo ho tlhophiso ea PDM.
- Maemo a mangata: E lumella boemo ho fetoha nako le nako ha konopo ea pushe e tobetsoa. E thusa ho khetha li-setting tse fapaneng.
Ho Beha Nako ea Nako:
O ka hlalosa litekanyetso tse fapaneng bakeng sa konopo ea pushbutton ho latela hore na e hatelloa nako e kae. Lumella lebokose la ho hlahloba nako liphanele tsa litlhophiso ho hlophisa tšobotsi ena.
Phetolelo e butsoeng ea tšebeliso:
Haeba u sebelisa Keypad ho kenya AiM ntle le sesebelisoa se seholo, latela mehato e fanoeng bakeng sa ho hlalosa melapo ea CAN.
LBH:
- Nka khoasolla software ea AiM RaceStudio3 joang?
Ho khoasolla software, etela AiM website at aim-sportline.com ebe u ea sebakeng sa download sa Software/Firmware. - A na nka reka lithapo tsa CAN tse setseng bakeng sa Keypad?
E, lithapo tsa CAN li ka rekoa ka thoko. Sheba linomoro tsa likarolo tse amanang le tsona bakeng sa ho odara. - A na nka amahanya maemo a ON le OFF ka bolokolohi le boleng ba linomoro?
E, maemo a mabeli ON le OFF a ka amahanngoa le boleng ba linomoro ha u lokisa likonopo tsa Keypad.
Selelekela
- AiM Keypad ke mefuta e mecha ea li-extensions tsa AiM tse thehiloeng ho protocol ea CAN Bus e sebelisoang ka mokhoa o ikhethileng marang-rang a AiM; li ka kopanngoa feela le AiM PDM08 kapa PDM32.
- Keypad e fumaneha ka liphetolelo tse fapaneng ho ea ka palo ea li-pushbuttons tseo e li hlahisang le tseo boemo ba tsona bo lulang bo fetisetsoa ho Network Master ka khokahano ea AiM CAN.
- Likonopo tsohle li ka hlophisoa ka botlalo ho sebelisoa AiM RaceStudio 3 Software.
Konopo ka 'ngoe e ka hlophisoa joalo ka:
- Nakoana: boemo ba pushbutton bo ON ha konopo e sutumetsoa
- Toggle: boemo ba li-pushbutton bo fetoha ho tloha ho ON ho ea ho TIMA nako le nako ha konopo ea pushe e sutumetsoa
- Maemo a mangata: boleng ba li-pushbutton bo fetoha ho tloha ho 0 ho ea ho MAX Value nako le nako ha konopo ea pushe e sutumetsoa.
U ka boela ua hlalosa moeli oa nako bakeng sa konopo e 'ngoe le e' ngoe e bolelang boitšoaro bo fapaneng ha ketsahalo ea khatello ea KHUTSANE kapa E LONG e fumanoa. Konopo e 'ngoe le e' ngoe e ka etsoa ka 'mala o fapaneng kapa ka mokhoa o tiileng, o liehang, o potlakileng kapa o benyang. Letlapa la likonopo le arolelana liteishene tsohle tsa ho kenya tse ka sebelisoang - ka lebaka la 'mala oa LEDS - ka bobeli ho amohela ketsahalo ea ho hatella konopo kapa boemo ba sesebelisoa.
Qetellong, hoa khoneha ho lokisa konopo ea pushbutton ho eketsa kapa ho fokotsa boemo ba khanya ea keypad. le ho fetisetsa litaelo ho sesebelisoa se seholo. Tafole e ka tlase e bonts'a litšobotsi tsa mefuta e fumanehang ea Keypad.
| K6 | K8 | K15 | |
| Likonopo | 6 e hlophisehileng | 8 e hlophisehileng | 15 e hlophisehileng |
| Backlight | RGB e nang le khetho ea Dimming | ||
| Khokahano | AiM E KA KHONA ka likhokahanyo tse 5 tsa Binder 712 | ||
| 'Mele Thepa | Silicon ea rabara le PA6 GS30% e matlafalitsoeng | ||
| Litekanyo | 97.4x71x4x24mm | 127.4×71.4×24 | 157.4×104.4×24 |
| Boima ba 'mele | 120g | 150g | 250g |
| Ha e kenele metsi | IP67 | ||
Li-kits tse fumanehang le likarolo tse ling
Lisebelisoa tsa keypad tse fumanehang ke:
Letlapa la K6
Letlapa la K6
- Keypad K6+50 cm AiM CAN cable X08KPK6AC050
- Keypad K6+100 cm AiM CAN cable X08KPK6AC050
- Keypad K6+200 cm AiM CAN cable X08KPK6AC050
- Keypad K6+400 cm AiM CAN cable X08KPK6AC050
Letlapa la K8
- Keypad K8+50 cm AiM CAN cable X08KPK8AC050
- Keypad K8+100 cm AiM CAN cable X08KPK8AC100
- Keypad K8+200 cm AiM CAN cable X08KPK8AC200
- Keypad K8+400 cm AiM CAN cable X08KPK8AC400
Letlapa la K15
- Keypad K15+50 cm AiM CAN cable X08KPK15AC050
- Keypad K15+100 cm AiM CAN cable X08KPK15AC100
- Keypad K15+200 cm AiM CAN cable X08KPK15AC200
- Keypad K15+400 cm AiM CAN cable X08KPK15AC400
Li-Keypad tsohle li tla le thapo ea CAN e sebelisoang ho e hokahanya le sesebelisoa se seholo empa lithapo le tsona li ka rekoa ka thoko e le likarolo tse ling.
Linomoro tse amanang le karolo ke:
- 50 cm AiM CAN cable V02554790
- 100 cm AiM CAN cable V02554810
- 200 cm AiM CAN cable V02554820
- 400 cm AiM CAN cable V02554830
Likonopo tsa litšoantšo:
- 72 likotoana letšoao la X08KPK8KICONS
- lets'oao le le leng tlanya mona ho tseba nomoro ea karolo ka 'ngoe ea setšoantšo
Tlhophiso ea software
- Bakeng sa ho lokisa li-keypads tsa AiM, ka kopo khoasolla software ea AiM RaceStudio3 ho tsoa ho AiM website at aim-sportline.com Software/firmware download sebaka: AiM – Software/Firmware download (aim-sportline.com)
Kamora ho kenya software, e tsamaise 'me u latele mehato ena:
- Kenya Lethathamo la Litlhophiso ka ho tobetsa letšoao le totobalitsoeng ka tlase:
- Tobetsa konopo ea "New" ho toolbar e ka holimo ka ho le letona 'me u khethe PDM eo u lakatsang ho e lokisa
- Software e kenya PDM Configuration
- Kenya "CAN Expansions" tab (1) ebe o tobetsa "Katoloso e Ncha" (2)
- Khetha Keypad e lakatsehang (K8 ho example)
- E lokise
lemoha ka kopo: sesebelisoa sa hau se ka sehloohong se khona ho laola boholo ba li-keypad tse 8.
Litlhophiso tsa li-pushbuttons
Lintlha tse ling tse potlakileng pele re qala ho sekaseka mokhoa oa ho lokisa AiM Keypads:
- boemo ba pushbutton bo ka beoa joalo ka Momentary, Toggle kapa Multi-status joalo ka ha ho hlalositsoe serapeng sa 3.1.1.; Hape hoa khoneha ho beha moeli oa nako ho laola khatello ea konopo e khutšoanyane le e telele ka litsela tse fapaneng
- boemo ba pushbutton bo lula bo fetisoa ka bese ea AiM CAN
- boemo ba konopo e 'ngoe le e' ngoe ka matla OFF e ka tsosolosoa ka matla a latelang ON
- konopo e 'ngoe le e' ngoe e ka etsoa ka mokhoa o ikhethileng - e tiileng kapa ea panya - ka mebala e 8 e fapaneng joalo ka ha ho hlalositsoe serapeng sa 3.1.2
- hoa khoneha ho lokisa konopo ea pushbutton ho eketsa kapa ho fokotsa boemo ba khanya ea LED
- ho seta konopo ea pushe e le Momentary o ka amahanya taelo ("Menu enter" joalo-joalo) ho konopo e 'ngoe le e 'ngoe ea push.
Litlhophiso tsa boemo ba li-pushbuttons
U ka beha mefuta e fapaneng ka konopo e 'ngoe le e' ngoe:
MOTS'OANE. boemo ke:
- ON ha pushbutton e sutumetsoa
- TLOA ha konopo ea pushe e lokolloa
Lemoha ka kopo: maemo ka bobeli ON le OFF a ka amahanngoa ka bolokolohi le boleng ba linomoro.
Lemoha ka kopo: ho beha feela konopo ea Momentary, o ka amahanya taelo ho konopo e 'ngoe le e' ngoe empa ho etsa joalo hoa hlokahala hore u kentse Ponts'o ho tlhophiso ea PDM.
Mabapi le setšoantšo se ka tlase, ho kenyelletsa ponts'o ho tlhophiso ea PDM:
- kenya tab ya Pontsho (1)
- phanele ea khetho e khothalletsoa hore u khethe eo u tla e eketsa (2)
- tobetsa "OK" (3) 'me u khethe sebopeho se lakatsehang phaneleng e khothalletsoang
Litaelo tse teng ke:
- Fetola leqephe la pontšo:
- Leqephe le hlahlamang la pontšo
- Leqephe le hlahang pele
- Bontša konopo:
- Kenya menu: ho tsamaya ho menu ya pontsho: ho hlokahala dikonopo tse nne; ba ba basweu ha ba bang bona ba holofetse. Ka kopo elelloa: li-pushbuttons tse sebelisitsoeng li fetoha ho latela boemo - bo otlolohileng kapa bo otlolohileng - ba keypad ea hau, ka lebaka lena khetho ea boemo ea hlokahala.
- Kenya hopola: taelo ena e kenya sehopotso sa data ka mor'a tlhahlobo.
- Seta botjha dialamo tseo boemo ba tsona ba pheletso e leng konopo e tobetswang.
- Seta li-counters bocha:
- Seta li-odometer tsohle hape.
- Seta bocha odometer "x" (ho latela palo ea li-odometer tse fumanehang)
- Khanya ea likonopo
- Keketseho
- Ho fokotseha
TOGGLE, boemo ke:
• ON ha konopo e sutumetsoa hang, 'me e lula ON ho fihlela e sutumetsoa hape
• TLOA ha konopo e sutumetsoa lekhetlo la bobeli.
Lemoha ka kopo: maemo ka bobeli ON le OFF a ka amahanngoa ka bolokolohi le boleng ba linomoro
MALTI-STATUS: boemo bo ka 'na ba nka litekanyetso tse fapaneng tse fetohang nako le nako ha pushbutton e sutumetsoa. Litlhophiso tsena li na le thuso, mohlalaample, ho khetha limmapa tse fapaneng kapa ho beha maemo a fapaneng a ho emisa jj.
Ho sa tsotellehe hore na pushbutton e behiloe joang, u ka boela ua beha moeli oa nako: tabeng ena, konopo ea pushbutton e behiloe ho litekanyetso tse peli tse fapaneng tseo u ka li hlalosang ho itšetlehile ka hore na u e sutumelletsa nako e kae.
Ho etsa joalo lumella "sebelisa nako" lebokose la ho hlahloba lebokoseng le ka holimo la liphanele tsa litlhophiso. 
Tokiso ea 'mala oa Pushbutton
Konopo e 'ngoe le e' ngoe e ka hlophisoa ka mebala e fapaneng ho bontša ketso e entsoeng ke mokhanni le maikutlo a ketso eo: konopo e ka fetoloa - bakeng sa ex.ample – ho panya (bonya kapa kapele) THOBALA ho bontsha hore e sutulitsoe, le ho tiya TSA BOTSHWANE ha ketso e kenngwa tshebetsong.
Liphetolelo tsa keypad tse bulehileng
Keypad e boetse e fanoa ka mofuta oa "Open" o u lumellang ho hlalosa melapo ea CAN. Phetolelo ena e reretsoe ho sebelisoa ha sesebelisoa sa AiM master se le sieo, empa ehlile, u ka se sebelisa ts'ebetsong efe kapa efe ea AiM. Ho etsa sena, o tlameha ho latela mehato ena:
- seta Keypad e le "hokahane le sesebelisoa sa AiM"
- fetisa tlhophiso
- bula tlhophiso ea Sesebelisoa sa AiM
- khetha "Open" ea katoloso 'me u e hlophise e le Keypad K8 e tloaelehileng.
Metako ea tekheniki
Litšoantšo tse latelang li bonts'a litekanyo le pinout ea AiM Keypads.
Keypad litekanyo tsa K6 ka mm [inchi]
Keypad K6 pinout
Boholo ba Keypad K15 ka mm [inchi]: 
Keypad K15 pinout: 
Litokomane / Lisebelisoa
 |
AiM K6 Remote Button Interface [pdf] Bukana ea Mosebelisi K6, K8, K15, K6 Remote Button Interface, K6, Remote Button Interface, Button Interface, Interface |
