UM1075
Bukana ea mosebelisi
ST-LINK/V2 in-circuit debugger/programmer
bakeng sa STM8 le STM32
Selelekela
ST-LINK/V2 ke sesebelisoa sa in-circuit debugger/programmer bakeng sa li-microcontrollers tsa STM8 le STM32. Mojule oa single wire interface (SWIM) le JTAG/ serial wire debugging (SWD) li-interfaces li nolofalletsa puisano le mochine ofe kapa ofe oa STM8 kapa STM32 o sebetsang botong ea kopo.
Ntle le ho fana ka ts'ebetso e ts'oanang ea ST-LINK/V2, ST-LINK/V2-ISOL e na le ho itšehla thajana ka dijithale pakeng tsa PC le boto ea kopo e reretsoeng. E boetse e mamella voltagho fihlela ho 1000 V RMS.
Sehokelo sa USB sa lebelo le felletseng se nolofalletsa puisano le komporo le:
- Lisebelisoa tsa STM8 ka ST Visual Develop (STVD) kapa ST Visual Programme (STVP) software (e fumanehang ho tsoa ho STMicroelectronics)
- Lisebelisoa tsa STM32 ka IAR™, Keil ® , STM32CubeIDE, STM32CubeProgrammer, le STM32CubeMonitor tikoloho e kopanetsoeng ea ntlafatso.
Likaroloana
- Matla a 5 V a fanoang ke sehokelo sa USB
- USB 2.0 segokanyimmediamentsi sa sebolokigolo ka botlalo
- thapo ya USB e tlwaelehileng ho tloha ho A ho ya ho Mini-B
- Likarolo tse ikhethileng tsa SWIM
- 1.65 ho 5.5 V kopo ea voltage tšehelitsoe ho sebopeho sa SWIM
- Mefuta ea SWIM ea lebelo le tlase le lebelo le holimo e tšehelitsoe
- Sekhahla sa lebelo la lenaneo la SWIM: 9.7 le 12.8 Kbytes/s, ka ho latellana, bakeng sa lebelo le tlase le le phahameng
- Cable ea SWIM bakeng sa ho hokela ts'ebeliso ka sehokelo se otlolohileng sa ERNI (ref: 284697 kapa 214017) kapa sehokelo se otlolohileng (ref: 214012)
- Cable ea SWIM bakeng sa ho hokela sesebelisoa ka hlooho ea phini kapa sehokelo sa molumo oa 2.54 mm - JTAG/ SWD (Serial Wire Debug) likarolo tse ikhethang
- 1.65 ho 3.6 V kopo ea voltage tšehelitsoe ke JTAG/ SWD interface le lisebelisoa tse mamellang 5 V (a)
– JTAG cable bakeng sa ho hokahanya le J e tloaelehilengTAG 20-pin pitch 2.54 mm sehokelo
- E tšehetsa JTAG puisano, ho fihla ho 9 MHz (ka ho sa feleng: 1.125 MHz)
- E ts'ehetsa serial wire debug (SWD) ho fihla ho 4 MHz (default: 1.8 MHz), le mohala oa serial viewer (SWV) puisano, ho fihlela ho 2 MHz - Karolo ea ntlafatso ea firmware e tšehelitsoeng (DFU)
- Boemo ba LED, bo benya nakong ea puisano le PC
- 1000 V RMS e phahameng ea ho itšehla thajanatage (ST-LINK/V2-ISOL feela)
- Mocheso o sebetsang ho tloha ho 0 ho isa ho 50 degrees Celsius
Ho odara litaba
Ho odara ST-LINK/V2, sheba Lethathamo la 1.
Lethathamo la 1. Lenane la likhoutu tsa odara
| Odara khoutu | ST-LINK tlhaloso |
| ST-LINK/V2 | In-circuit debugger/programmer |
| ST-LINK/V2-ISOL | In-circuit debugger/programmer ka ho itšehla thajana ka dijithale |
a. ST-LINK/V2 e khona ho hokahana le lipehelo tse sebetsang ka tlase ho 3.3 V empa e hlahisa mats'oao a phallo ka sekhahla sena.tage level. Lipheo tsa STM32 li mamella ho fetella honatage. Haeba likarolo tse ling tsa boto e shebiloeng li utloahala, sebelisa ST-LINK/V2-ISOL, STLINK-V3MINIE, kapa STLINK-V3SET ka adaptara ea B-STLINK-VOLT ho qoba tšusumetso ea ho fetella.tage ente botong.
Likahare tsa sehlahisoa
Lithapo tse fanoeng ka har'a sehlahisoa li bonts'itsoe ho Setšoantšo sa 2 le sa 3. Li kenyeletsa (ho tloha ka ho le letšehali ho ea ho le letona):
- thapo ya USB e tlwaelehileng ho ya ho ya ho Mini-B (A)
- ST-LINK/V2 debugging le programming (B)
- Sehokelo sa SWIM sa theko e tlase (C)
- SWIM ribone e bataletseng e nang le sehokelo se tloaelehileng sa ERNI pheletsong e 'ngoe (D)
- JTAG kapa ribone e bataletseng ea SWD le SWV e nang le sehokelo sa lipini tse 20 (E)
Sebopeho sa Hardware
ST-LINK/V2 e entsoe ho pota-pota sesebelisoa sa STM32F103C8, se kenyeletsang Arm e sebetsang hantle haholo ®(a) Cortex®.
-M3 ea mantlha. E fumaneha ka har'a sephutheloana sa TQFP48.
Joalokaha ho bontšitsoe setšoantšong sa 4, ST-LINK/V2 e fana ka lihokelo tse peli:
- Sehokelo sa STM32 sa JTAG/ SWD le SWV interface
- Sehokelo sa STM8 bakeng sa sehokelo sa SWIM
ST-LINK/V2-ISOL e fana ka sehokelo se le seng bakeng sa STM8 SWIM, STM32 J.TAG/ SWD, le li-interface tsa SWV.
- A = STM32 JTAG le sehokelo sa sepheo sa SWD
- B = Sehokelo sa sepheo sa STM8 SWIM
- C = STM8 SWIM, STM32 JTAG, le sehokelo sa sepheo sa SWD
- D = Ts'ebetso ea puisano LED
4.1 Khokahano le STM8
Bakeng sa nts'etsopele ea lits'ebetso tse thehiloeng ho li-microcontrollers tsa STM8, ST-LINK/V2 e ka hokahanngoa le boto e shebiloeng ka likhoele tse peli tse fapaneng, ho latela sehokelo se fumanehang botong ea kopo.
Lithapo tsena ke:
- Ribone e sephara ea SWIM e nang le sehokelo se tloaelehileng sa ERNI pheletsong e 'ngoe
- Cable ea SWIM e nang le likhokahanyo tse peli tsa 4-pin, 2.54 mm kapa likhoele tse arohaneng tsa SWIM
4.1.1 Khokahano e tloaelehileng ea ERNI e nang le ribone e bataletseng ea SWIM
Setšoantšo sa 5 se bontša mokhoa oa ho hokahanya ST-LINK/V2 haeba sehokelo se tloaelehileng sa ERNI 4-pin SWIM se le teng botong ea kopo.
- A = Boto ea kopo e shebiloeng e nang le sehokelo sa ERNI
- B = Mohala oa mohala o nang le sehokelo sa ERNI pheletsong e 'ngoe
- C = sehokelo sa sepheo sa STM8 SWIM
- Sheba Setšoantšo sa 11
Setšoantšo sa 6 se bontša hore pin 16 ha e eo ho ST-LINK/V2-ISOL sehokelo sa target. Pini ena e sieo e sebelisoa e le senotlolo sa polokeho sehokelong sa thapo, ho netefatsa boemo bo nepahetseng ba thapo ea SWIM sehokelong se shebiloeng esita le lithakhisa tse sebelisoang bakeng sa SWIM le J.TAG likhoele.
4.1.2 Khokahano ea SWIM e theko e tlase
Setšoantšo sa 7 se bontša mokhoa oa ho hokahanya ST-LINK/V2 haeba 4-pin, 2.54 mm, sehokelo sa SWIM se theko e tlaase se teng botong ea kopo.
- A = Letlapa la kopo ea kopo le 4-pin, 2.54 mm, sehokelo sa theko e tlase
- B = Thapo ea terata e nang le sehokelo sa 4-pin kapa thapo e arohaneng
- C = sehokelo sa sepheo sa STM8 SWIM
- Sheba Setšoantšo sa 12
4.1.3 Matshwao a SWIM le dikgokelo
Tab le 2 e akaretsa mabitso a matshwao, mesebetsi, le matshwao a kgokelo ya sepheo ha o sebedisa thapo ya terata e nang le sehokedi sa 4-pin.
Lethathamo la 2. Lihokelo tsa ribone tse bataletseng tsa SWIM bakeng sa ST-LINK/V2
| Tšoaea no. | Lebitso | Mosebetsi | Khokahano ea sepheo |
| 1 | VDD | Sepheo sa VCC(1) | MCU VCC |
| 2 | DATA | SESA | Pin ea ho sesa ea MCU |
| 3 | GND | LEFATŠE | GND |
| 4 | RETS'ELISITSOE | RETS'ELISITSOE | MCU RESET phini |
1. Motlakase o tsoang ho boto ea kopo o hokahane le ST-LINK/V2 debugging le boto ea lenaneo ho netefatsa hore matšoao a lumellana pakeng tsa mapolanka ka bobeli.
Tab le 3 e akaretsa mabitso a mats'oao, mesebetsi, le mats'oao a khokahanyo ea sepheo ka ho sebelisa thapo ea mehala e arohaneng.
Kaha thapo ea terata e arohaneng ea SWIM e na le likhokahano tse ikemetseng bakeng sa lithakhisa tsohle ka lehlakoreng le le leng, hoa khoneha ho hokahanya ST-LINK/V2-ISOL ho boto ea kopo ntle le sehokelo se tloaelehileng sa SWIM. Riboneng ena e bataletseng, 'mala o ikhethileng le leibole ho nolofatsa khokahano holima litšupiso tsa matšoao ohle.
Letlapa la 3. SWIM likhokahano tsa cable tse theko e tlaase bakeng sa ST-LINK/V2-ISOL
| Mmala | Lebitso la mohala oa mohala | Mosebetsi | Khokahano ea sepheo |
| Khubedu | CCTV | Sepheo sa VCC(1) | MCU VCC |
| Botala | UART-RX | E sa sebelisoeng | E bolokiloe (2) (ha e hokahane le boto e shebiloeng) |
| Boputsoa | UART-TX | ||
| Bosehla | BOOTO | ||
| namunu | SESA | SESA | Pin ea ho sesa ea MCU |
| Ntsho | GND | LEFATŠE | GND |
| Bosoeu | SESA-RST | RETS'ELISITSOE | MCU RESET phini |
1. Motlakase o tsoang ho boto ea kopo o hokahane le ST-LINK/V2 debugging le boto ea lenaneo ho netefatsa hore matšoao a lumellana pakeng tsa mapolanka ka bobeli.
2. BOOT0, UART-TX, le UART-RX li boloketsoe tsoelo-pele e tlang.
TVCC, SWIM, GND, le SWIM-RST li ka hokeloa ho sehokelo sa theko e tlase sa 2.54 mm kapa ho penya lihlooho tse fumanehang botong e shebiloeng.
4.2 Khokahano le STM32
Bakeng sa nts'etsopele ea lits'ebetso tse ipapisitseng le li-microcontroller tsa STM32, ST-LINK/V2 e tlameha ho hokahana le ts'ebeliso ho sebelisoa 20-pin J e tloaelehileng.TAG lente le sephara le fanoeng.
Tab le 4 e akaretsa mabitso a matšoao, mesebetsi, le matšoao a hokahaneng a sepheo sa 20-pin J.TAG lente le bataletseng ho ST-LINK/V2.
Letlapa la 5 le akaretsa mabitso a mats'oao, mesebetsi, le mats'oao a khokahano ea sepheo sa 20-pin J.TAG lente le bataletseng ho ST-LINK/V2-ISOL.
Lethathamo la 4. JTAG/ SWD likhokahano tsa cable ho STLINK-V2
| Pin che. | ST-LINK/V2 sehokedi (CN3) | ST-LINKN2 tshebetso | Khokahano ea sepheo (JTAG) | Khokahano ea sepheo (SWD) |
| 1 | VAPP | Sepheo sa VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | GND | GND | GNDK3) | GND(3) |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | GND | GND | GND(3) | GND(3) |
| 7 | TMS SWDIO | JTAG TMS, SW 10 | JTMS | SWDIO |
| 8 | GND | GND | GND(3) | GND(3) |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | GND | GND | GND(3) | GND(3) |
| 11 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESWOO) |
| 14 | GND | GND | GND(3) | GND(3) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | GND | GND | GNDK3) | GND(3) |
| 17 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | VDD | VDD (3.3 V) | Ha e kopane | Ha e kopane |
| 20 | GND | GND | GND(3) | GND(3) |
- Motlakase o tsoang ho boto ea kopo o hokahane le ST-LINK/V2 debugging le boto ea lenaneo ho netefatsa hore matšoao a lumellana pakeng tsa mapolanka.
- Hokela ho GND bakeng sa phokotso ya lerata lenteng.
- Bonyane e 'ngoe ea lithakhisa tsena e tlameha ho hokelloa fatše bakeng sa boitšoaro bo nepahetseng. Ho kgothaletswa ho kopanya kaofela ha bona.
- Ka boikhethelo: Bakeng sa mohala oa serial Viewer (SWV) mohlala.
Lethathamo la 5. JTAG/ SWD likhokahano tsa cable ho STLINK-V2-ISOL
| Tšoaea no. | Sehokelo sa ST-LINK/V2 (CN3) | ST-LINKN2 mosebetsi | Khokahano ea sepheo (JTAG) | Khokahano ea sepheo (SWD) |
| 1 | VAPP | Sepheo sa VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | SWDIO |
| 8 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 9 | TCK SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | Ha e sebelisoe(5) | Ha e sebelisoe(5) | Ha e kopane(5) | Ha e kopane(5) |
| 11 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI, SWO | JTDO | TRACESW0(4) |
| 14 | Ha e sebelisoe(5) | Ha e sebelisoe(5) | Ha e kopane(5) | Ha e kopane(5) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 17 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 20 | GND | GND | GND(3) | GND(3) |
- Motlakase o tsoang ho boto ea kopo o hokahane le ST-LINK/V2 debugging le boto ea lenaneo ho netefatsa hore matšoao a lumellana pakeng tsa mapolanka.
- Hokela ho GND bakeng sa phokotso ya lerata lenteng.
- Bonyane e 'ngoe ea lithakhisa tsena e tlameha ho hokelloa fatše bakeng sa boitšoaro bo nepahetseng. Ho kgothaletswa ho kopanya kaofela ha bona.
- Ka boikhethelo: Bakeng sa mohala oa serial Viewer (SWV) mohlala.
Lethathamo la 5. JTAG/ SWD likhokahano tsa cable ho STLINK-V2-ISOL
| Tšoaea no. | Sehokelo sa ST-LINK/V2 (CN3) | ST-LINKN2 mosebetsi | Khokahano ea sepheo (JTAG) | Khokahano ea sepheo (SWD) |
| 1 | VAPP | Sepheo sa VCC | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | TRST | JTAG TRST | NJTRST | GND(2) |
| 4 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 5 | TDI | JTAG TDO | JTDI | GND(2) |
| 6 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 7 | TMS SWDIO | JTAG TMS. SW 10 | JTMS | SWDIO |
| 8 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 9 | TCK SWCLK | JTAG TCK. SW CLK | JTCK | SWCLK |
| 10 | Ha e sebelisoe(5) | Ha e sebelisoe(5) | Ha e kopane(5) | Ha e kopane(5) |
| 11 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 12 | GND | GND | GND(3) | GND(3) |
| 13 | TDO SWO | JTAG TDI. SWO | JTDO | TRACESW0(4) |
| 14 | Ha e sebelisoe(5) | Ha e sebelisoe(5) | Ha e kopane(5) | Ha e kopane(5) |
| 15 | NRST | NRST | NRST | NRST |
| 16 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 17 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 18 | GND | GND | GND(3) | GND(3) |
| 19 | Ha e kopane | Ha e kopane | Ha e kopane | Ha e kopane |
| 20 | GND | GND | GND(3) | GND(3) |
- Motlakase o tsoang ho boto ea kopo o hokahane le ST-LINK/V2 debugging le boto ea lenaneo ho netefatsa hore matšoao a lumellana pakeng tsa mapolanka.
- Hokela ho GND bakeng sa phokotso ya lerata lenteng.
- Bonyane e 'ngoe ea lithakhisa tsena e tlameha ho hokelloa fatše bakeng sa boitšoaro bo nepahetseng. Ho kgothaletswa ho kopanya kaofela ha bona.
- Ka boikhethelo: Bakeng sa mohala oa serial Viewer (SWV) mohlala.
- E sebelisoa ke SWIM ho ST-LINK/V2-ISOL (sheba Lethathamo la 3).
Setšoantšo sa 9 se bonts'a mokhoa oa ho hokela ST-LINK/V2 ho sepheo u sebelisa sebopeho sa JTAG thapo.
- A = Letlapa la kopo ea boto le JTAG sehokedi
- B = JTAG/SWD 20-wire flat cable
- C = STM32 JTAG le sehokelo sa sepheo sa SWD
Tšebeliso ea sehokelo se hlokahalang botong ea kopo e shebiloeng ke: 2x10C e koahelang hlooho 2x40C H3/9.5 (pitch 2.54) - HED20 SCOTT PHSD80.
Hlokomela: Bakeng sa lits'ebetso tse theko e tlase, kapa ha sehokelo se tloaelehileng sa 20-pin 2.54 mm-pitch se le seholo haholo, hoa khoneha ho kenya tšebetsong TAG-Hokela tharollo. The TAG-Connect adaptara le thapo li fana ka mokhoa o bonolo le o ka tšeptjoang oa ho hokahanya ST-LINK/V2 kapa ST-LINK/V2ISOL ho PCB ntle le ho hloka karolo ea mating ho PCB ea kopo.
Bakeng sa lintlha tse ling mabapi le tharollo ena le tlhaiso-leseling ea kopo-PCB-footprint, etela www.tag-connect.com.
Litšupiso tsa likarolo tse lumellanang le JTAG le lihokelo tsa SWD ke:
a) adaptara ea TC2050-ARM2010 (boto ea lipini tse 20 ho isa ho tse 10)
b) TC2050-IDC kapa TC2050-IDC-NL (Ha ho maoto) (thapo ea lipini tse 10)
c) TC2050-CLIP e bolokang sekotwana se tla sebelisoa le TC2050-IDC-NL (ho ikhethela)
4.3 ST-LINK/V2 boemo ba LED
LED e ngotsoeng COM ka holim'a ST-LINK/V2 e bontša boemo ba ST-LINK/V2 (ho sa tsotellehe mofuta oa khokahanyo). Ka botlalo:
- Lebone la LED le benya bofubelu: ho ntse ho etsahala palo ea pele ea USB e nang le PC
- LED e khubelu: puisano pakeng tsa PC le ST-LINK/V2 e thehiloe (qetellong ea ho bala)
- LED e benya botala / bokhubelu: Lintlha li fapanyetsanoa lipakeng tsa sepheo le PC
- LED e tala: puisano ea ho qetela e atlehile
- Lebone la LED le na le lamunu: puisano ea ST-LINK/V2 le sepheo e hlotsoe.
Tlhophiso ea software
5.1 ST-LINK/V2 ntlafatso ea firmware
ST-LINK/V2 e kenya mochine oa ntlafatso oa firmware bakeng sa lintlafatso tsa sebaka ka boema-kepe ba USB. Joalo ka ha firmware e ka fetoha nakong ea bophelo ba sehlahisoa sa ST-LINK/V2 (ts'ebetso e ncha, litokiso tsa liphoso, ts'ehetso bakeng sa malapa a macha a li-microcontroller), ho khothalletsoa ho etela nako le nako maqephe a inehetseng ho. www.st.com ho lula u le morao-rao ka mofuta oa morao-rao.
5.2 nts'etsopele ea ts'ebeliso ea STM8
Sheba ho ST toolset Pack24 e nang le patch 1 kapa ea morao-rao, e kenyeletsang ST Visual Develop (STVD) le ST Visual Programmer (STVP).
5.3 nts'etsopele ea ts'ebeliso ea STM32 le mananeo a flash
Lisebelisoa tsa mekhatlo ea boraro (IAR ™ EWARM, Keil ® MDK-ARM ™ ) li tšehetsa ST-LINK/V2 ho latela liphetolelo tse fanoeng ho Tab le 6 kapa phetolelo ea morao-rao e fumanehang.
Lethathamo la 6. Mokhoa oo liketane tsa lisebelisoa tsa mokha oa boraro li tšehetsang ST-LINK/V2
| Moamehi e mong | Ketane ea lisebelisoa | Phetolelo |
| IAR™ | EWARM | 6.2 |
| Keil® | MDK-ARM™ | 4.2 |
ST-LINK/V2 e hloka mokhanni oa USB ea inehetseng. Haeba sesebelisoa sa sesebelisoa se sa e kenye ka bo eona, mokhanni a ka fumanoa ho www.st.com tlas'a lebitso la STSW-LINK009.
Ho tseba haholoanyane ka lisebelisoa tsa mokha oa boraro, etela tse latelang weblibaka:
Maqheka
Legend bakeng sa litlhaloso tsa phini:
VDD = Sepheo sa voltagle kutloisiso
DATA = SWIM DATA mola pakeng tsa target le debug tool
GND = Phatlalatso voltage
RESET = Ho tsosolosa tsamaiso ea sepheo
Legend bakeng sa litlhaloso tsa phini:
VDD = Sepheo sa voltagle kutloisiso
DATA = SWIM DATA mola pakeng tsa target le debug tool
GND = Phatlalatso voltage
RESET = Ho tsosolosa tsamaiso ea sepheo
Nalane ea ntlafatso
Lethathamo la 7. Histori ea ntlafatso ea litokomane
| Letsatsi | Khatiso | Liphetoho |
| 22-Apr-11 | 1 | Tokollo ea pele. |
| 3-Phup-11 | 2 | Letlapa la 2: Lihokelo tsa ribone tse bataletseng tsa SWIM bakeng sa ST-LINK/V2: e kentse mongolo o botlaaseng ba leqephe 1 mosebetsing oa "Target VCC". Lethathamo la 4: JTAG/ SWD likhokahano tsa cable: e kentse mongolo o botlaaseng ba leqephe mosebetsing "Target VCC". Lethathamo la 5: Kamoo liketane tsa lithulusi tsa mekhatlo ea boraro li tšehetsang ST-LINK/V2: e nchafalitse "Liphetolelo" tsa IAR le Keil. |
| 19-Ag-11 | 3 | E kenyellelitse lintlha tsa mokhanni oa USB ho Karolo ea 5.3. |
| 11-May-12 | 4 | E kentse SWD le SWV ho JTAG likarolo tsa khokahano. Lethathamo la 4 le Fetotsoeng: JTAG/ likhokahano tsa lithapo tsa SWD. |
| 13-Sep-12 | 5 | E kentse khoutu ea odara ea ST-LINKN2-ISOL. Ntlafatso ea Karolo ea 4.1: nts'etsopele ea ts'ebeliso ea STM8 leqepheng la 15. Keletso e Ekelitsoeng 6 ho Lethathamo la 4. Keletso e Ekelitsoeng "Bakeng sa lits'ebetso tse theko e tlase…" pele ho Karolo ea 3.3: STLINK/V2 boemo ba LED leqepheng la 14. |
| 18-Oct-12 | 6 | E ekelitsoe Karolo ea 5.1: ntlafatso ea firmware ea ST-LINK/V2 leqepheng la 15. |
| 25-Mar-16 | 7 | Boleng bo ntlafalitsoeng ba VRMS ho Selelekela le Likarolo. |
| 18-Oct-18 | 8 | Lethathamo la 4 le ntlafalitsoeng: JTAG/ SWD likhokahano tsa cable le mongolo oa eona o botlaaseng ba leqephe. Liphetoho tse nyane ho tokomane eohle. |
| 9-Jan-23 | 9 | Selelekela, Likarolo, le Karolo ea 5.3 e ntlafalitsoeng: nts'etsopele ea ts'ebeliso ea STM32 le mananeo a flash. Lethathamo la 5 le Nchafalitsoeng: Mokhoa oo liketane tsa lisebelisoa tsa mokha oa boraro li tšehetsang ST-LINK/V2. Liphetoho tse nyane ho tokomane eohle. |
| 3-Apr-24 | 10 | Lethathamo la Pele 4 JTAG/ likhokahano tsa cable tsa SWD li arotsoe ho Lethathamo la 4: JTAG/ SWD likhokahano tsa cable ho STLINK-V2 le Lethathamo la 5: JTAG/ SWD likhokahano tsa cable ho STLINK-V2-ISOL. |
TSEBISO EA BOHLOKOA – BALA KA HLOKO
STMicroelectronics NV le li-subsidiary tsa eona ("ST") li na le tokelo ea ho etsa liphetoho, litokiso, lintlafatso, lintlafatso, le lintlafatso ho lihlahisoa tsa ST le/kapa tokomaneng ena ka nako efe kapa efe ntle le tsebiso. Bareki ba lokela ho fumana lintlha tsa morao-rao tse amanang le lihlahisoa tsa ST pele ba fana ka litaelo. Lihlahisoa tsa ST li rekisoa ho latela lipehelo le maemo a thekiso ea ST ka nako ea tumello ea taelo. Bareki ke bona ba ikarabellang bakeng sa khetho, khetho, le tšebeliso ea lihlahisoa tsa ST mme ST ha e nke e le molato bakeng sa thuso ea kopo kapa moralo oa lihlahisoa tsa bareki.
Ha ho laesense, e hlalositsoeng kapa e boletsoeng, ea tokelo efe kapa efe ea thepa ea mahlale e fanoeng ke ST mona.
Ho rekisoa ha lihlahisoa tsa ST ka litokisetso tse fapaneng le tlhahisoleseding e boletsoeng mona ho tla hlakola waranti leha e le efe e fanoeng ke ST bakeng sa sehlahisoa se joalo.
ST le logo ea ST ke matšoao a khoebo a ST. Bakeng sa lintlha tse ling mabapi le matšoao a khoebo a ST, sheba ho www.st.com/trademarks. Mabitso a mang kaofela a lihlahisoa kapa litšebeletso ke thepa ea beng ba tsona.
Lintlha tse tokomaneng ena li nkela sebaka le ho nkela tlhahisoleseding e neng e fanoe pele liphetolelong tsa pele tsa tokomane ena.
© 2024 STMicroelectronics – Litokelo tsohle li sirelelitsoe
Litokomane / Lisebelisoa
 |
ST ST-LINK-V2 In Circuit Debugger Programmer [pdf] Bukana ea Mosebelisi ST-LINK-V2, ST-LINK-V2-ISOL, ST-LINK-V2 In Circuit Debugger Programmer, ST-LINK-V2, In Circuit Debugger Programmer, Circuit Debugger Programmer, Debugger Programmer |