14POINT7 Spartan 3 Lambda Sensor
Tlhokomediso
- Se ke oa hokela kapa oa hakolla Sensor ea Lambda ha Spartan 3 e ntse e sebelisoa.
- Sensor ea Lambda e tla chesa haholo nakong ea ts'ebetso e tloaelehileng, ka kopo ela hloko ha u e tšoara.
- Se ke oa kenya Sensor ea Lambda ka tsela eo yuniti e tsamaisoang ka eona pele enjene ea hau e sebetsa. Enjene e qalang e ka tsamaisa condensation tsamaisong ea hau ea ho qeta ho ea ho sensor, haeba sensor e se e ntse e futhumetse sena se ka baka tšabo ea mocheso 'me sa etsa hore li-ceramic tse ka hare ho sensor li phunyehe le ho senyeha.
- Le hoja Sensor ea Lambda e ntse e le mocheng o sebetsang oa ho qeta matla, e tlameha ho laoloa ke Spartan 3. Carbon e tsoang mokelikeli o sebetsang e ka hahoa habonolo holim'a sensor e se nang matla le ho e silafatsa.
- Bophelo ba sensor ea Lambda ha bo sebelisoa ka mafura a etellang pele bo pakeng tsa 100-500 hrs.
- Spartan 3 e lokela ho ba ka phaposing ea mokhanni.
- U se ke ua khoaela thapo ea lambda.
Litaba tsa Sephutheloana
1x Spartan 3, 8ft lambda cable, 2x blade fuse holder, tse peli 1 Amp blade fuse, tse peli 5 Amp fuse ea lehare.
Ho qeta ho kenya
Sensor ea Lambda e lokela ho kenngoa pakeng tsa hora ea 10 le boemo ba 2 hora, e ka tlase ho likhato tse 60 ho tloha holimo, sena se tla lumella matla a khoheli ho tlosa condensation ea metsi ho tloha ho sensor. Bakeng sa lisebelisoa tsohle tsa Oxygen sensor, sensor e tlameha ho kenngoa pele ho converter ea catalytic. Bakeng sa lienjineri tse lakatsehang, sensor e lokela ho kenngoa hoo e ka bang 2ft ho tloha boema-kepe ba enjene. Bakeng sa lienjini tsa Turbocharged sensor e lokela ho kenngoa kamora turbocharger. Bakeng sa lienjine tsa Supercharged sensor e lokela ho kenngoa 3ft ho tloha boema-kepe ba enjene.
Wiring
Sensor Mocheso oa LED
Spartan 3 e na le LED e khubelu ea onboard, e ka bonoang ka likheo tsa mekotla, ho bonts'a Mocheso oa LSU. Ho panya butle ho bolela hore sensor e pholile haholo, leseli le tiileng le bolela hore mocheso oa sensor o lokile, ho panya ka potlako ho bolela hore sensor e chesa haholo.
Khokahano ea serial-USB
Spartan 3 e na le serial e hahelletsoeng ho USB converter ho fana ka likhokahano tsa USB le komporo ea hau. Mofetoleli o ipapisitse le chipset e tsebahalang ea FTDI kahoo lits'ebetso tse ngata li se li kentse mokhanni esale pele.
Litaelo tsa serial
LSU Heater Ground, Pin 4 on screw terminal, e tlameha ho hokelloa ho kenya litaelo tsa serial
| Serila Command | Tlhokomeliso ea Tšebeliso | Morero | Example | Feme ea kamehla |
| GETHW | E fumana mofuta oa Hardware | |||
| GETFW | E fumana mofuta oa firmware | |||
| SETTYPEx | Haeba x ke 0 joale Bosch LSU 4.9
Haeba x ke 1 joale Bosch LSU ADV |
E beha mofuta oa sensor ea LSU | SETTYPE1 | X=0, LSU 4.9 |
| GETTYPE | E fumana mofuta oa sensor ea LSU | |||
| SETCANFORMATx | x ke palo e felletseng ea litlhaku tse 1 ho isa ho tse 3. x=0; ya kamehla
x=1; Kopanya le ECU x=2; Adaptronic ECU x=3; Haltech ECU x=4; % Oksijene*100 |
SETCANFORMAT0 | x=0 | |
| GETCANFORMAT | E fumana sebopeho sa CAN | |||
| SETCANIDx | x ke palo e felletseng ea litlhaku tse 1 ho isa ho tse 4 ka bolelele | E beha 11 bit CAN id | SETCANID1024
SETCANID128 |
x=1024 |
| GETCANID | E fumana 11 bit CAN id | |||
| SETCANBAUDx | x ke palo e felletseng ea litlhaku tse 1 ho isa ho tse 7 ka bolelele | E beha CAN Baud Rate | SETCANBAUD1000000
e tla beha CAN Baud sekhahla ho isa ho 1Mbit/s |
X=500000,
500kbit / s |
| GETCANBAUD | Fumana CAN Baud Rate | |||
| SETCANRx | Haeba x ke 1 sehanyetsi se tla sebetsa. Haeba x ke 0 the
resistor e holofetse |
Noble/Thibela CAN
Resistor ea ho emisa |
SETCANR1
SETCANR0 |
x=1, KANNA nako
Res Nobled |
| GETCANR | Fumana CAN Term Res State;
1=sebelisoa, 0=e holofalitsoe |
|||
| SEAFRMxx.x | xx.x ke decimal ka bolelele ba litlhaku tse 4
ho kenyelletsa le lintlha tsa decimal |
E beha AFR Multiplier bakeng sa
Sesebelisoa sa torque |
SEAFM14.7
SEAFM1.00 |
x=14.7 |
| GETAFRM | E fumana AFR Multiplier bakeng sa
Sesebelisoa sa torque |
|||
| SETLAMFIVEVx.xx | x.xx ke decimal hantle feela litlhaku tse 4 ho kenyeletsoa le ntlha ea decimal. Bonyane boleng ke 0.60, boholo ba boleng ke 3.40. Boleng bona bo ka ba holimo kapa ka tlase ho feta
boleng ba SETLAMZEROV. |
E beha Lambda ho 5[v] bakeng sa tlhahiso ea linear | SETLAMFIVEV1.36 | x=1.36 |
| GETLAMFIVEV | E fumana Lambda ka 5[v] | |||
| SETLAMZEROVx.xx | x.xx ke decimal hantle feela litlhaku tse 4 ho kenyeletsoa le ntlha ea decimal. Bonyane boleng ke 0.60, boholo ba boleng ke 3.40. Boleng bona bo ka ba holimo kapa ka tlase ho feta
SETLAMFIVEV boleng. |
E beha Lambda ho 0[v] bakeng sa tlhahiso ea linear | SETLAMZEROV0.68 | x=0.68 |
| GETLAMZEROV | Fumana Lambda ka 0[v] | |||
| SETPERFx | Haeba x ke 0 joale tshebetso e tloaelehileng ea 20ms. Haeba x ke 1 joale ts'ebetso e phahameng ea 10ms. Haeba x e le 2 joale ntlafatsa bakeng sa lean
ts'ebetso. |
SETPERF1 | x=0, tshebetso e tlwaelehileng | |
| GETPERFx | E fumana tshebetso | |||
| SETSLOWHEATx | Haeba x ke 0 joale sensor e futhumatsoa ka lebelo le tloaelehileng nakong ea matla a qalang.
Haeba x e le 1 joale sensor e futhumatsoa ka 1/3 lebelo le tloaelehileng nakong ea matla a qalang. Haeba x ke 2 joale emela MegaSquirt 3 CAN Letšoao la RPM pele le futhumatsa. |
SETSLOWHEAT1 | X=0, sekhahla se tloaelehileng sa mocheso oa kutlo | |
| TS'ELISITSOE TS'OANE | E fumana maemo a slowheat | |||
| MEMRESET | Khutlisa ho li-setting tsa feme. |
| SETLINOUTx.xxx | Moo x.xxx e leng decimal ka bolelele ba litlhaku tse 5 ho kenyeletsoa le ntlha ea decimal, e kholo ho feta 0.000 le ka tlase ho 5.000. Linear Output e tla qala hape e tloaelehileng
ts'ebetso ea ho qala bocha. |
E lumella mosebelisi ho beha High Perf Linear Output hore e be molumo o itsengtage | SETLINOUT2.500 | |
| DOCALA | E hloka Firmware 1.04 le ka holimo | Etsa Free Air Calibration 'me u bontše boleng.
E khothaletsoa ho clone li-sensor feela. |
||
| GETCLE | E hloka Firmware 1.04 le ka holimo | E Fumaneha Mahala Moeeng
boleng |
||
| RESETKALI | E hloka Firmware 1.04 le ka holimo | E seta botjha Tekanyetso ya Moya ya Mahala
boleng ho 1.00 |
||
| SETCANDRx | x ke palo e felletseng ea litlhaku tse 1 ho isa ho tse 4 ka bolelele
E hloka Firmware 1.04 le ka holimo |
E beha CAN Data Rate ka hz | X=50 | |
| GETCANDR | E hloka Firmware 1.04 le ka holimo | E fumana CAN Data Rate |
Litaelo tsohle li ho ASCII, linyeoe ha li na taba, libaka ha li na taba.
Windows 10 serial terminal
LSU Heater Ground, Pin 4 on screw terminal, e tlameha ho hokeloa ho fihlella terminal ea serial Theminale ea serial e khothaletsoang ke Termite, https://www.compuphase.com/software_termite.htm, ka kopo, khoasolla le ho kenya seta se felletseng.
- Ho Windows 10 bareng ea ho batla, ka kopo thaepa "Device Manager" 'me ue bule.
- Spartan 3 e tla hlaha e le "USB Serial Port", ho example "COM3" e abetsoe Spartan 3.
- Ho Termite, tobetsa "Settings"
- Etsa bonnete ba hore Boema-kepe bo nepahetse le hore sekhahla sa Baud ke "9600".
CAN Bus Protocol Format (Lambda)
Bakeng sa %O2 CAN Format ka kopo, sheba "Spartan 3 le Spartan 3 Lite for Lean Burn le Oxygen Metering Applications.pdf" Spartan 3's CAN Bus e sebetsa ka 11 bit addressing.
- Sekhahla sa kamehla sa CAN Baud ke 500kbit/s
- Default CAN Termination resistor e butswe, sena se ka fetoloa ka ho romela "SETCANRx" serial command.
- Default CAN Id ke 1024, sena se ka fetoloa ka ho romela "SETCANIDx" serial command.
- Bolelele ba data (DLC) ke 4.
- Default Data Rate ke 50 hz, data e romelloa ka mor'a 20[ms], sena se ka fetoloa ka ho romela "SETCANDRx" serial command.
- Lintlha[0] = Lambda x1000 High Byte
- Lintlha[1] = Lambda x1000 Low Byte
- Lintlha[2] = LSU_Temp/10
- Lintlha[3] = Boemo
- Lambda = (Boitsebiso[0]<<8 + Data[1])/1000
- Mocheso oa Sensor [C] = Data[2]*10
Lisebelisoa tsa CAN tse tšehetsoeng
| Lebitso | KA Format
Serila Command |
KA NA Id serial
Taelo |
KA BAUD Rate Serial Command | Hlokomela |
| Kopanya le ECU | SETCANFORMAT1 | SETCANID950 | SETCANBAUD1000000 | Bala "Spartan 3 ho hokahanya G4+
ECU.pdf" bakeng sa lintlha tse ling |
| ECU ea Adaptronic | SETCANFORMAT2 | SETCANID1024
(Default from factory) |
SETCANBAUD1000000 | |
| MegaSquirt 3 ECU | SETCANFORMAT0
(Default from factory) |
SETCANID1024
(Default from factory) |
SETCANBAUD500000
(Default from factory) |
Bala "Spartan 3 ho MegaSquirt
3.pdf" |
| Haltech ECU | SETCANFORMAT3 | Ha ho hlokahale | SETCANBAUD1000000 | Spartan 3 E Emula Haltech WBC1
wideband controller |
| YourDyno Dyno
Molaoli |
SETCANFORMAT0
(Default from factory) |
SETCANID1024
(Default from factory) |
SETCANBAUD1000000 |
E KA Felisa Mohanyetsi
A re re re bitsa ECU; Master, le lisebelisoa tse romellang/amohelang data ho/ho tsoa ho ECU eo re e bitsang; Lekhoba (Spartan 3, dashboard ea dijithale, molaoli oa EGT, joalo-joalo…). Likopong tse ngata ho na le Master (ECU) a le mong le Makhoba a le mong kapa ho feta ao kaofela a arolelanang CAN Bus e tšoanang. Haeba Spartan 3 e le eena feela Lekhoba ka beseng ea CAN joale CAN Termination Resistor ho Spartan 3 e lokela ho sebelisoa ho sebelisoa serial command "SETCANR1". Ka ho sa feleng, CAN Termination Resistor ho Spartan 3 e ea sebetsa. Haeba ho na le Makhoba a mangata, Lekhoba le hole ho feta Monghali (ho ipapisitsoe le bolelele ba terata) le lokela ho ba le CAN Termination Resistor e lumelletsoeng, Makhoba a mang kaofela a tlameha ho ba le CAN Termination Resistor ea bona.
holofetse/kgaotswe. Ka ts'ebetso; hangata ha ho na taba hore na li-CAN Termination Resistors li setiloe hantle, empa bakeng sa ts'epahalo e phahameng ka ho fetisisa, li-CAN Termination Resistors li lokela ho hlophisoa hantle.
Bootloader
Ha Spartan 3 e tsamaisoa ntle le LSU Heater Ground e hokahaneng, e tla kenya mokhoa oa bootloader. Ho matlafatsa Spartan 3 ka Heater Ground e hokahaneng ho ke ke ha qala bootloader mme Spartan 3 e tla sebetsa joalo ka tloaelo. Ha Spartan 3 e le ka mokhoa oa Bootloader ho na le LED e ka holim'a sekepe, e ka bonoang ka li-slits, tse tla benya botala bo tiileng. Ha o le boemong ba bootloader, litaelo tsa serial ha li khonehe. Ka mokhoa oa Bootloader, ho ka khoneha feela ntlafatso ea firmware, mesebetsi e meng kaofela e koetsoe.
Ho kenya mokhoa oa bootloader bakeng sa ntlafatso ea firmware:
- Etsa bonnete ba hore Spartan 3 e timme, ha ho na matla a ho Pina 1 kapa Pin 3 ea "screw terminal".
- Tlosa sensor
- Hakolla LSU Heater Ground ho Pin 4 ea theminale ea screw
- Matla ho Spartan 3,
- Lekola hore na LED e ka holim'a sekepe e benya botala bo tiileng, haeba ke ka nako eo Spartan 3 ea hau e leng mokhoeng oa bootloader.
Tiisetso
14Point7 e fana ka tumello ea hore Spartan 3 e se be le bofokoli ka lilemo tse peli.
Boithorollo
14Point7 e ikarabella bakeng sa ts'enyehelo feela ho fihlela theko ea theko ea lihlahisoa tsa eona. Lihlahisoa tsa 14Point7 ha lia lokela ho sebelisoa litseleng tsa sechaba.
Litokomane / Lisebelisoa
 | Sensor ea Spartan 3 Lambda |
Litšupiso
- compuphase.com/software_termite.htmwww.compuphase.com
- Bukana ea Mosebelisimanual.tools