iBoard® ka APS
IB-191C Mohato Bar
BALA LITAELO KA HLOKO PELE U QALA HO KENYA.
REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
*ROCKER PANELE THABA
*HA HO CHEBA HO HLOKANG
KAROLO #: IB-191C&H
| Boholo ba Fastener | Torque e tiisang (ft-Ibs) | Ho hlokahala |
| 6 limilimithara | 6-7 | X |
| 8 limilimithara | 16-18 | 4 |
| 10 limilimithara | 31-32 | 4 |
| 12 limilimithara | 56-58 | X |
| 14 limilimithara | 92-94 | X |
LENANE LA KAROLO
Sephutheloana sa Hardware A (Bakeng sa ho Kenya Bracket)
| Ntho | QTY | Tlhaloso |
| 1# | 2 | Lipoleiti tsa tšehetso |
| 2# | 2 | Lihlatsoa tse Rectangular |
| 3# | 4 | Lipoleiti tsa M10X50 T-Bolt |
| 4# | 4 | Setšoantšo sa M10X35 Bolt |
| 5# | 10 | Lisebelisoa tsa polasetiki tsa M10 |
| 6# | 2 | M10X1.5-30 Hex Bolts |
| 7# | 8 | Lihlatsoa tsa M10 tse bataletseng |
| 8# | 12 | M10 Nylon Lock Nuts |
| 9# | 2 | M10X1.5-40 Hex Bolts |
| 10# | 2 | M10X1.5-40 Carriage Bolts |
| 11# | 6 | Li-washer tse kholo tsa M10 |
| 12# | 2 | M10 Hex Nuts |
| 13# | 4 | M8X1.25-30 Hex Bolts |
| 14# | 8 | Lihlatsoa tsa M8 tse bataletseng |
| 15# | 4 | M8 Nylon Lock Nuts |
Sephutheloana sa Hardware B (Bakeng sa Kemiso ea Bohato ba Bohato ba Stainless Steel)
| Ntho | QTY | Tlhaloso |
| 1# | 12 | Liboutu tsa koloi tsa M8X1.25-35mm |
| 2# | 12 | Li-washer tse kholo tsa M8 |
| 3# | 12 | M8 Nylon Lock Nuts |
| 4# | 6 | Li-slider (tse Pakiloeng ka Mehato ea Mehato) |
MOHATO 1
Start installation from the driver side front of the vehicle. Locate and remove the factory oval rubber plug and the (2) round rubber plugs in the bottom of the floor panel located closest to the front tire opening, (Figs 1& 2).
MOHATO 2
Select (1) M10X1.5-40 Carriage Bolt, (1) Rectangular Washer and (1) M10 Plastic Washer, (Fig 3A). Slide the Rectangular Washer onto and over the square shoulder on the Carriage Bolt. Thread the M10 Plastic Washer part way onto the Bolt.
HLOKOMELA: The M10 Plastic Washer is designed to help hold the Bolt in place during installation. Insert the Carriage Bolt with Rectangular Washer and Plastic Washer into the inner round hole in the floor panel. Line up the Carriage Bolt with the center of the hole and the Rectangular Washer across the hole. Pull the Carriage Bolt down through the slot in the Washer. Thread the Plastic Washer down tight against the floor panel, (Fig 3B). 
MOHATO 3
Select (1) M10X50 T-Bolt Plate and (1) M10 Plastic Washer, Fig 4A). Insert the T-Bolt up into the oval hole and rotate it 90degrees so that the block is across the oval hole. Thread the Plastic Washer onto the T-Bolt and tight against the floor panel, Fig 4B).
MOHATO 4
Khetha (1) Bracket Mounting Front Bracket (DFM) le (1) Bracket Front Support Bracket (DFS). Kopano e nang le (1) M10X1.5-30 Hex Bolt, (2) M10 Flat Washers le (1) M10 Nylon Lock Nut, (Fig 5). U se ke ua tiisa ka botlalo hardware ka nako ena.
MOHATO 5
Secure the Driver Front Mounting Bracket (DFM) to the installed M10X50 T-Bolt Plate with (1) M10 Large Flat Washer and (1) M10 Nylon Lock Nut, (Fig 6). Do not fully tighten hardware at this time. Slide the Driver Front Support Bracket (DFS) onto the M10X1.5 -40 Carriage Bolt with (1) M10 Flat Washer and (1) M10 Nylon Lock Nut, (Fig 6). Do not fully tighten hardware at this time.
MOHATO 6
Move along the side of the vehicle to the center location below where the front and rear doors meet. Locate the 4th and 5th hole in the floor panel from the front wheel opening, (Fig 7). Remove the (2) rubber plugs. Select (2) M10X35 Bolt Plates and (2) M10 Plastic Washers. Insert (1) M10X35 Bolt Plate with (1) M10 Plastic Washer into the first and second round hole in the floor panel next to the pinch weld, (Figs 8A & 8B). IMPORTANT: Install the Bolt Plates with the “Plates” pointing toward each other, (see Fig 8C). Attach (1) Locking Plate to the (2) Bolt Plates with (1) M10 Large Flat Washer and (1) M10 Nylon Lock Nut, (Fig 9). Do not fully tighten hardware.
MOHATO 7
Khetha (1) Driver Center Mounting Bracket (DCM) le (1) Driver Center Support Bracket (DCS). Kopano e nang le (2) M8X1.25-30 Hex Bolts, (4) M8 Flat Washers le (2) M8 Nylon Lock Nuts, (Fig 10). U se ke ua tiisa ka botlalo hardware ka nako ena.
MOHATO 8
Select (1) Driver Center Mounting Bracket (DCM), (1) M10X1.540 Hex Bolt, (1) Support Plate and (1) M10 Hex Nut. Thread the M10 Hex Nut all the way down the M10X1.5-40 Hex Bolt. Insert the Hex Bolt with Nut up and into the welded nut on the tab on the Center Bracket, (Fig 11).
HLOKOMELA: Thread the Bolt in until a few threads are sticking out of the welded nut. Do not thread the hex bolt all of the way into the welded nut. Place (1) Support Plate onto the threaded end of the M10X1.5-40 Hex Bolt, (Fig 11). Continue to
thread the Hex Bolt in until the Support Plate is close to but not touching the bottom of the body panel.
BOHLOKOA: Do not tighten the hardware on the Center Brackets until the final Steps, (see Step 15). Select (1) Driver Center Support Bracket (DCS), hang the Cen- ter Support Bracket onto the M10x35 Bolt Plate and over the Lock Plate secure with (1) M10 Flat Washer and (1) M10 Nylon Lock Nut, (Fig 12). Do not fully tighten hardware at this time.
MOHATO 9
Move to the rear of the vehicle, (Fig 13). Remove the oval rubber plug. Select (1) M10X50 T-Bolt Plate with (1) M10 Plastic Washer, (Fig 14A). Insert the T-Bolt up into the oval hole and rotate 90-degrees so that the block is across the oval hole. Thread the Plastic Retainer onto the T-Bolt and tight against thefloor panel as described in Step 3, (Fig 14B).
MOHATO 10
Khetha Bracket Rear Mounting Bracket (DRM). E fanyeha Bracket e ka Morao ho T-Bolt e nang le (1) M10 Large Flat Washer le (1) M10 Lock Nut ea Nylon, (Fig 15). Se ke oa tiisa hardware ka ho feletseng.
MOHATO 11
Hang ha li-brackets tsohle (3) tse kenyang lehlakoreng la bakhanni li kentsoe, joale tsoela pele ho kenya mohato oa Mohato. (Setšoantšo sa 16 & 17)
- Khetha (1) Slider le (2) M8X1.25-35mm Bolts ea likoloi;
- Kenya (2) M8X1.25-35mm Liboutu tsa Koloi ho (1) Slider.
- Tsamaisa Selaete (ka liboutu tsa kariki) ho Mohato oa Mohato.
- Pheta ho kenya li-slider tse ling (2) ho bareng ea mohato.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 17). Do not fully tighten hardware at this time.
Hlokomela: Li-Slider li tletse ka Li-Step Bars. Beha boemo 'me u lokise Sebaka sa Mohato 'me u tiise lisebelisoa tsohle ka botlalo.
MOHATO 12
Sheba ho bona hore na Step Bar e boemong ba koloi, ka pele ho ea ka morao, eseng ho ea fatše. Fetola Li-Brackets ho kena kapa ho tsoa ha ho hlokahala ho etsa mola oa Step Bar ka lehlakoreng la koloi. Tsamaea ho Bracket e ka morao 'me hang ha e lumellane, tiisa M10 Nylon Lock Nut ho T-Bolt, (Fig 15).
MOHATO 13
E latelang, fetela ho Bracket e ka pele. Tiisa lisebelisoa tsa T-Bolt le Bolt Plate feela, (Figs 3A & 4A). Fetola bophahamo ba Bracket e ka pele ha ho hlokahala. Hang ha u se u hlophisitsoe hantle, tiisa M10 Hex Bolt e sireletsang Bracket ea Tšehetso ho ea pele ea Mounting Bracket, (Fig 6).
MOHATO 14
Ka Li-Brackets tse ka pele le tse ka morao li tiisitsoe ka ho feletseng koloing, fallela Center Bracket, (Fig 18).
a. Tiisa ka botlalo M10 Nylon Lock Nut e bolokang Bracket ea Tšehetso ho Bolt Plate.
b. Ka bonolo sutumelletsa Mounting Bracket holimo 'me u be boemong bo tlase ho Mohato oa Mohato.
c. Tiisa (2) M8 Hex Bolts.
d. Butle-butle tiisa M10X1.5-40 Hex Bolt ho fihlela Letlapa la Tšehetso le ts'oaroa ka tlase ho karolo ea 'mele.
e. Fetolela Hex Bolt (2) ka ho thinya ka botlalo ho eketsa ho kenya pele. Tobetsa M10 Nylon Lock Nut ho notlela Bolt sebakeng.
MOHATO 15
Beha boemo 'me u lokise Sebaka sa Mohato 'me u tiise lisebelisoa tsohle ka botlalo.
Pheta Mehato ea 1-15 bakeng sa ho kenya lehlakoreng le leng la Mohato oa Bohato. Kemiso e phethetsoe.
Tlhokomeliso
Etsa tlhahlobo ea nako le nako ha u kenya ho etsa bonnete ba hore lisebelisoa tsohle li bolokehile ebile li tiile.
E le ho sireletsa litšepe/liboto tsa hau, ka kopo sebelisa sesepa se bonolo/lihlahisoa tse sa cheng bakeng sa ho hloekisa feela.
https://www.iboardauto.com/iboard-videos/
Tšehetso ea Bareki: info@iboardauto.com
Litokomane / Lisebelisoa
 |
iBoard IB-191C Mohato Bar [pdf] Tlhophiso Tataiso IB-191C, IB-191H, IB-191C Step Bar, IB-191C, Step Bar, Bar |