HOPERF HPNI01 LoRa Transceiver Module

Tlhaloso e Akaretsang ea HPNI01

HPNI01 is an ultra-low-power, high-performance LoRa transceiver for various frequency of 868,915 MHz wireless applications.It is part of the SEMTECH RF product line, which includes complete transmitters, receivers and transceivers .The high integration of HPNI01 simplifies the peripheral materials needed in the system design. The sensitivity up to – 136 dBm which can optimize the link performance of applications. In addition, HPNI01 also supports Duty-Cycle operation mode, channel interception, high-precision RSSI, power-on reset, noise output and other more functions, which makes the application design more flexible thus to achieve product differentiation design. The working voltage of HPNI01 is 3.3V. When the sensitivity is reaching -136  dBm, it only consumes 12.5 mA current. Thisultra-low power mode can further reduce the power consumption of the chip.

Likaroloana

• Frequency Range: 868，915MHz
• Ho feto-fetoha ha molumo oa lentsoe: LoRa
• Data Rate: 0.018~37.5 kbps
• Sensitivity: -136 dBm , BW=125KHz, SF=12
• Moqtage Range: 1.8 ~ 3.3V
• Receiving Current: 12.5 mA @ BW=125KHz
• BW: Supports a maximum of 500 KHz
• Supports Ultra Low Power Receiving Mode
• Sleeping Current:1.5ua
• 4-wire SPI Interface
• Supports Full-automatic Independent Working Mode

Lisebelisoa

• Automatic meter Reading
• Home Security&Building automation
• ISM Band Data Communication
• Industrial Monitoring & C
• Security System ntrolling
• Sesebelisoa sa Remote Control
• Seletsa se Bohlale
• Phepelo le Tsamaiso
• Temo e Bohlale
• Smart City
• Retailing
• Asset Following
• Smart Lighting System
• Smart Parking
• Tlhokomelo ea Tikoloho
• Tlhokomelo ea Bophelo bo Botle

Pin ea Sehlahisoa

Letlapa1. Tlhaloso ea Pin ea Mojule ea HPNI01

 

Pin No.	Pin Lebitso	Tlhaloso
1	ANT1	Antenna Input &Output TX:14dbm
2,4,15,16	GND	Digital Ground
3	ANT2	Antenna Output TX:20dbm
5	VCC	Moqtag3.3V
6	DIO0	Data Input & Output, Software Configuration
7	DIO1	Data Input & Output, Software Configuration
8	DIO2	Data Input & Output,Receiving Data Output
9	DIO3	Data Input & Output, Software Configuration
10	RETS'ELISITSOE	Reset, Active Low
11	TS'ELISO	SPI clock Input
12	MISO	SPI Data Output
13	MOSI	SPI Data Input
14	NSS	SPI slave Input

Litekanyetso tsa motlakase

Testing conditions: Power supply 3.3V, temperature 25℃

Paramethara	Letšoao	Maemo	Bonyane	Boleng bo Tlwaelehileng	Boholo	Yuniti
Phepelo Voltage	VDD		1.8	3.3	3.7	V
Ho sebetsa Mocheso	T		-40		85	℃
Phepelo ea motlakase Moqtage Moepa			1			mV/rona

Paramethara	Letšoao	Maemo	Bonyane	Boholo	Yuniti
Phepelo Voltage	VDD		-0.5	3.9	V
Sehokedi Moqtage	VIN		-0.3	3.3	V
JunctionTemper pheko	TJ		-40	125	℃
Polokelo Mocheso	TSTG		-50	150	℃
Soldering Mocheso	TSDR	E qeta bonyane lilemo tse 30		255	℃
ESD Level[2]	HBM		-2	2	kV
Latch Current	@ 85 ℃		-100	100	mA

Paramethara	Maemo	Bonyane	Boleng bo Tlwaelehileng	Boholo	Yuniti
Mamello ea Hangata	HPNI01		868		MHz
			915
Matla a ho Fetisa	ANT1 VCC=3.3v	-	13	-	dBm
	ANT2 VCC=3.3v	-	18
Fetisetsa Current	868MHz ANT1	-	35	60	mA
	868MHz ANT2	-	120	140
	915MHz ANT1	-	35	60
	915MHz ANT2	-	120	140
Ho Amohela Hona Joale	868/915MHz	-	12.5	18	mA

Receiving Sensitivity (Lora) SF12, BW 125KHz CR4/5

868/915MHz

-

-136

-

dBm

Nalane ea Phetoho

Phetolelo	Letsatsi la ntlafatso	Ntlafatsa litaba
V1.0	2024.12.20	Tokollo ea pele

Phatlalatso ea FCC

1. Sesebelisoa sena se lumellana le Karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
   1. Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi.
   2. Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
2. Liphetoho kapa litokiso tse sa amoheloang ka ho hlaka ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.

Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
• Eketsa karohano pakeng tsa thepa le moamoheli.
• Hokela lisebelisoa sebakeng sa seketsoana se fapaneng le seo moamoheli a hokahaneng le sona.
• Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.

Sesebediswa sena se hlahlobilwe ho kopana le ditlhoko tse akaretsang tsa kgahlamelo ya RF. Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka sa bonyane 20 cm pakeng tsa radiator le 'mele oa hau.
The Module is designed to comply with the FCC statement. FCC ID is 2ASEO-

HPNI01. The host system using the Module should have a label indicating it contains the modular’s FCC ID: 2ASEO-HPNI01. This radio module must not installed to co-locate and operating simultaneously with other radios in host system additional testing and equipment authorization may be required to operating simultaneously with other radio. The Module and its antenna must not be co-located or operating in conjunction with any other transmitter or antenna within a host device.
The modular must be installed in the host that is assigned by Company name: Shenzhen HOPE Microelectronics Co., Ltd, Model no.: HPNI01. If other host types used would need further evaluation and possible C2PC if they are not significantly similar to the one tested The Module is designed for a compact PCB design. It should be installed and operated with host or other minimum distance of 20 centimeters between the radiator and your body.” To comply with FCC regulations limiting both  maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 2.15 dBi in the 902.0 MHz to 928.0 MHz. The module uses an External Antenna interface and ping angle interface antenna, this antenna is sold with the module.

Tsebiso ho sehokahanyi sa OEM
The end user manual shall include all required regulatory information/warning as shown in this manual. The OEM integrator is responsible for testing their end product for any additional compliance requirements required with this module installed. If the final product contains circuits of other FCC PART 15 Subparts, the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. The intended use is generally not for the general public, it is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required, the user has no access to the connector. Installation must be controlled. Installation requires special training.

Sesebelisoa sena se lumellana le Karolo ea 15 ea Melao ea FCC
This equipment should be installed and operated with a minimum distance of 20 cm  between the radiator and your body.

Polelo ea ISED
The Module is designed to comply with the ISED statement. ISED Certification Number is 24999-HPNI01. The host system using  the Module should have a label indicating it contains the modular’s IC: 24999-HPNI01. This radio module must not installed to co-locate and operating simultaneously with other radios in host system additional testing and equipment authorization may be required to operating simultaneously with other radio. The Module and its antenna must not be co-located or operating in conjunction with any other transmitter or antenna within a host device.
Sesebelisoa sena se na le li-transmitter/baamoheli ba sa lumelloeng ke laesense ba tsamaisanang le Boqapi, Saense, le Ntlafatso ea Moruo ea RSS(li)laesense ea Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

Phaello e kholo ea antenna (ka dBi): 2.15 dBi
Mofuta oa Antenna: Antenna ea ka ntle

Mokhoa oa puisano

• Shenzhen HOPE Microelectronics Co., Ltd.
• Address: 30/F, Building 8, Zone C, Vanke Cloud City, Liuxin 4th Street, Xili, Nanshan, Shenzhen 518055, China
• Mohala: +86-755-82973805
• Lithekiso: sales@hoperf.com
• Websebaka: www.hoperf.com

LBH

• Matla a phahameng a RF a tsoang mojuleng oa HPNI01 ke afe?
  Matla a phahameng a tlhahiso ea RF ea mojule oa HPNI01 ke 60dBm.
• Mofuta oa antenna o sebelisitsoeng le mojule oa HPNI01 ke ofe?
  Mojule oa HPNI01 o sebelisa Antenna ea Kantle bakeng sa ts'ebetso.

Litokomane / Lisebelisoa

HOPERF HPNI01 LoRa Transceiver Module [pdf] Buka ea Mong'a 2ASEO-HPNI01, 2ASEOHPNI01, hpni01, HPNI01 LoRa Transceiver Module, HPNI01, LoRa Transceiver Module, Transceiver Module, Module

Litšupiso

• Bukana ea Mosebelisi