1. Boitsebiso ba Bohlokoa ba Tšireletseho
Please read all instructions carefully before using the Uwant Y200-S Fabric Spot Cleaner. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Tšireletseho ea Motlakase: Always ensure the power cord is undamaged and plugged into a grounded outlet. Do not use with wet hands.
- Mouoane o Chesang: The cleaner produces 100°C steam. Avoid direct contact with skin or pets to prevent burns.
- Tšebeliso ea Metsi: Use only clean water in the clean water tank. Do not add cleaning solutions to the clean water tank unless specifically designed for steam cleaners and approved by Uwant.
- Polokelo: Boloka sesebelisoa ka tlung sebakeng se omileng.
- Bana le Liphoofolo: Beha sesebelisoa moo bana le liphoofolo tse ruuoang lapeng li fihlang teng.
- Tlhokomelo: Hlakola sesebelisoa pele u lokisa kapa ho hloekisa.
2. Sehlahisoa Overview
The Uwant Y200-S is a powerful fabric spot cleaner designed for deep cleaning and sanitizing various fabric surfaces using high-temperature steam and strong suction.
2.1 Likarolo tse Kenyellelitsoeng
- 1x Uwant Y200-S Spot Cleaner Main Unit
- 1x Hose Assembly
- 1x Steam Brush / Brush Head
- 1x Storage Clasp
- 1x Clean Water Tank
- 1x Waste Water Tank
2.2 Boitsebiso ba Karolo
Tlhaloso ea setšoantšo: A ka pele view of the Uwant Y200-S Fabric Spot Cleaner. The main body is grey, featuring two transparent tanks on the front: the upper tank for clean water and the lower tank for waste water. A control panel is visible on the top, and the hose connection port is on the side.
Tlhaloso ea setšoantšo: The flexible hose assembly, showing the connection point for the main unit on one end and the steam brush head attached to the other. The brush head has bristles and a suction nozzle.
3. Litaelo tsa ho seta
- Hlakola Sesebediswa: Tlosa ka hloko likarolo tsohle tsa sephutheloana. Boloka sephutheloana bakeng sa polokelo kapa sepalangoang nakong e tlang.
- Attach Hose Assembly: Insert the hose assembly connector firmly into the designated port on the main unit until it clicks into place.
- Attach Steam Brush Head: Connect the steam brush head to the end of the hose assembly. Ensure it is securely fastened.
- Tlatsa Tanka ea Metsi a Hloekileng:
- Tlosa tanka ea metsi a hloekileng ho tsoa yuniti e kholo.
- Open the tank cap and fill with clean tap water. Do not exceed the MAX fill line.
- Securely close the cap and reinsert the tank into the main unit.
Tlhaloso ea setšoantšo: A hand holding the clean water tank, pouring water into it. The tank is transparent with a visible MAX fill line.
- Hokela ho Matla: Hokela thapo ea motlakase sebakeng se loketseng sa motlakase se theohileng fatše.
4. Litaelo tsa Ts'ebetso
Before operating, ensure the clean water tank is filled and the waste water tank is empty and properly installed.
4.1 Ho Kenya Matla le ho Futhumatsa
- Press the Power button on the control panel. The indicator light will illuminate.
- The appliance will begin heating the water to 100°C. This process may take a few minutes. The indicator light may change or flash to show heating status.
- Once the desired temperature is reached, the indicator light will become solid, indicating the cleaner is ready for use.
4.2 Cleaning Procedure (Wash & Vacuum Simultaneously)
- Teko pele: Always test the cleaner on an inconspicuous area of the fabric first to ensure colorfastness and no adverse reactions.
- Sebelisa Steam: Hold the steam brush head over the stained area. Press the steam trigger on the handle to release hot steam. Move the brush head slowly over the area.
- Scrub (Optional): For stubborn stains, gently scrub the area with the brush bristles while applying steam.
- Metsi a Ntšang: Release the steam trigger. Press the vacuum suction button on the handle to activate the suction. Move the brush head over the wet area to extract the dirty water into the waste water tank.
- Pheta: Repeat steps 2-4 as necessary until the stain is removed and the area is as dry as possible.
Tlhaloso ea setšoantšo: A person demonstrating the use of the Uwant Y200-S Fabric Spot Cleaner on a sofa cushion. The steam brush head is pressed against the fabric, and a small amount of steam is visible.
4.3 Tubing Self-Cleaning Function
After each use, it is recommended to use the self-cleaning function to prevent odors and maintain hygiene.
- Netefatsa hore tanka ea metsi a hloekileng e na le metsi a lekaneng.
- Place the steam brush head into the designated self-cleaning port on the main unit (if available) or into a sink.
- Press and hold the self-cleaning button (refer to control panel diagram if available) for a few seconds. The appliance will flush clean water through the hose and suction it into the waste water tank.
- Lumella hore potoloho e phethe.
Tlhaloso ea setšoantšo: A close-up of the Uwant Y200-S main unit, showing the self-cleaning port where the steam brush head is inserted for the automatic cleaning cycle.
5. Tlhokomelo
Regular maintenance ensures optimal performance and extends the life of your Uwant Y200-S.
- Empty and Clean Waste Water Tank: After each use, remove the waste water tank, empty its contents, and rinse thoroughly with clean water. Allow it to air dry before reinserting.
- Tanka ea Metsi a Hloekileng: Periodically rinse the clean water tank to prevent mineral buildup.
- Clean Steam Brush Head: Remove any debris or hair from the brush bristles and suction nozzle. Rinse under running water.
- Hlakola Bokantle: Sebelisa bonolo, damp cloth to wipe the exterior of the main unit. Do not use harsh chemicals.
- Polokelo: Ensure both tanks are empty and dry before storing the appliance. Wrap the power cord neatly using the auto cord retraction feature (if applicable) or the storage clasp. Store in a cool, dry place.
6. Ho rarolla mathata
| Bothata | Lebaka le ka khonehang | Tharollo |
|---|---|---|
| Ha ho Matla | Appliance not plugged in; Power outlet faulty; Power button not pressed. | Check power cord connection; Test outlet with another device; Press the Power button firmly. |
| Ha ho Steam | Clean water tank empty; Appliance not heated sufficiently; Steam trigger not pressed. | Refill clean water tank; Wait for heating indicator light to become solid; Press steam trigger on handle. |
| Ho Amoha Mefokolo | Waste water tank full; Hose or nozzle clogged; Tank not properly sealed. | Empty waste water tank; Clear any blockages from hose/nozzle; Ensure tanks are securely in place. |
| Ho dutla ha Metsi | Tanks not properly seated; Hose connection loose; Overfilled clean water tank. | Ensure tanks are securely installed; Check hose connections; Do not overfill clean water tank. |
If the problem persists after attempting these solutions, please contact Uwant customer support.
7. Litlhaloso tsa Sehlahisoa
- Lebitso: Uwant
- Mohlala: Y200-S
- Nomoro ea Mohlala: Y200 Steam
- Boima ba Ntho: 6 lik'hilograma
- Mmala: Hlooho
- Mocheso oa Mouoane: 100°C
- Matla a Suction: 18kPa
- Naha ea tlhaho: China
- Likarolo tse Kenyelelitsoeng: Hose Assembly, Spot Cleaner Main Unit, Steam Brush / Brush Head, Storage Clasp, Waste Water Tank, Clean Water Tank
8. Tiisetso le Tšehetso ea Bareki
Uwant products are manufactured to high-quality standards. For warranty information, please refer to the warranty card included with your purchase or visit the official Uwant websebaka.
For technical assistance, troubleshooting not covered in this manual, or to order replacement parts, please contact Uwant customer support:
- Websebaka: www.uwant.com (Ka kopo sheba sebaka sa hau sa libaka websaete)
- Lengolo-tsoibila: Sheba sephutheloana sa sehlahisoa sa hau kapa websebaka sa marang-rang bakeng sa lengolo-tsoibila le ikhethileng.
- Mohala: Sheba sephutheloana sa sehlahisoa sa hau kapa website for specific contact number.
Please have your model number (Y200-S) and purchase date ready when contacting support.