Bogen AT10A 10-Watt Attenuator User Manual

Selelekela

This manual provides detailed instructions for the installation, operation, and maintenance of the Bogen AT10A 10-Watt Attenuator. The AT10A is designed to control the volume of individual speakers or groups of speakers in a constant voltage (70V or 25V) audio distribution system.

Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or connected equipment.

Sehlahisoa se Felletseview

Setšoantšo: Pele view of the Bogen AT10A 10-Watt Attenuator. The unit features a silver faceplate with a black rotary volume knob. The knob is marked with numbers from 0 to 10, indicating volume levels. The Bogen logo is visible at the bottom center, and "AT-10A" is printed in the bottom right corner.

The Bogen AT10A is a wall-plate style attenuator, providing 10 steps of volume control plus an "OFF" position. It is suitable for use with 25V or 70V constant voltage speaker lines and has a power rating of 10 watts.

Ho seta le ho Kenya

Litlhokomelo tsa Tšireletso

• Ensure all power to the audio system is disconnected before beginning installation.
• Ho kenya ho lokela ho etsoa ke basebetsi ba tšoanelehang ho latela melao ea motlakase ea lehae.
• Do not exceed the maximum power rating of 10 watts.

Ho phahamisa

1. The AT10A is designed to fit into a standard single-gang electrical box.
2. Secure the electrical box in the desired wall location.
3. Ensure adequate space for wiring connections behind the attenuator.

Lihokelo tsa Wiring

The AT10A features screw terminals for input and output connections. Refer to the diagram below for typical wiring.

• Hokela voltage audio source (e.g., amplifier output) to the "INPUT" terminals.
• Connect the speaker(s) to be controlled to the "OUTPUT" terminals.
• Maintain correct polarity (+ to + and - to -) for all connections.
• Netefatsa hore dikgokelo tsohle di sireletsehile ebile ha di na dipotoloho tse kgutshwane.

(Note: A detailed wiring diagram would typically be provided here by the manufacturer. For this manual, general instructions are given.)

Litaelo tsa Ts'ebetso

The Bogen AT10A provides simple rotary control for adjusting the volume level of connected speakers.

1. Matlafatsa: After installation, restore power to the audio system.
2. Ho Fetola Bolumo: Rotate the knob clockwise to increase the volume and counter-clockwise to decrease it.
3. Maemo a Bolumo: The knob features marked positions from 0 to 10. Position '0' represents the "OFF" or minimum volume setting, while '10' represents the maximum volume setting.
4. Choriso: Adjust the knob gradually to achieve the desired listening level.

Tlhokomelo

The Bogen AT10A is designed for reliable, long-term operation with minimal maintenance.

• Ho hloekisa: To clean the faceplate, gently wipe with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Tlhahlobo: Periodically check the attenuator for any visible damage or loose connections. If any issues are found, disconnect power and address them promptly.
• Ha ho na Likarolo tse ka Sebetsang: The internal components of the AT10A are not user-serviceable. Do not attempt to open or repair the unit. Refer servicing to qualified personnel.

Ho batle phoso

If troubleshooting steps do not resolve the issue, contact Bogen technical support or a qualified audio technician.

Litlhaloso

Tšehetso le Boitsebiso ba Boikopanyo

For technical assistance, product inquiries, or further information, please contact Bogen Communications, Inc.

• Moetsi: Bogen Communications, Inc.
• Websebaka: www.bogen.com (Example link, sehokelo sa 'nete se ka fapana)
• Tšebeletso ea bareki: Refer to the official Bogen websebaka sa marang-rang bakeng sa lintlha tsa hajoale tsa puisano.

Ela Hloko: Litlhaloso tsa sehlahisoa li ka fetoha ntle le tsebiso.