Buka ea Mosebelisi ea Projeke ea DLP e nkehang habobebe ea InFocus IN112

1. Selelekela

This manual provides essential information for the safe and efficient operation of your InFocus IN112 Portable DLP Projector. Please read these instructions thoroughly before using the projector and retain them for future reference.

The InFocus IN112 is designed for versatile use, offering high brightness and a strong contrast ratio. It incorporates BrilliantColor technology for clear image reproduction and is 3D-ready. Its compact and lightweight design facilitates easy portability and installation.

2. Se ka Lebokoseng

Netefatsa hore lintho tsohle tse thathamisitsoeng ka tlase li kenyelelitsoe ka har'a sephutheloana sa sehlahisoa sa hau:

• InFocus IN112 Projector
• Thapo ea matla
• RGB cable (VGA cable)
• A/V cable (Composite Video cable)
• Litaelo tsa polokeho
• Bukana ea mosebelisi (tokomane ena)
• Taolo e hole

3. Projector Overview

Setšoantšo sa 1: Holimo View - Displays the control panel with buttons for power, source selection, menu navigation, and keystone adjustment, along with the focus ring for the lens.

Setšoantšo sa 2: Lehlakore View - Shows the ventilation grilles essential for heat dissipation during operation. Ensure these are not obstructed.

Setšoantšo sa 3: Angled View le Remote - Illustrates the projector from an angle, highlighting the lens and the included remote control for convenient operation.

Setšoantšo sa 4: Ka morao View - Details the various input and output ports, including power, audio in/out, video, computer (VGA), RS232, and Mini USB.

4. Seta

4.1 Ho bea

Position the projector on a stable, flat surface or mount it securely. Ensure adequate ventilation around the projector to prevent overheating. The distance from the screen will determine the image size. Adjust the projector's position to achieve the desired image size and clarity.

4.2 Khokelo ea Matla

1. Connect the supplied power cord to the projector's power inlet.
2. Hokela ntlha e 'ngoe ea thapo ea motlakase sebakeng sa motlakase se theohileng fatše.

4.3 Ho hokela Mehloli ea Kenyelletso

The IN112 projector offers multiple input options:

• VGA (Computer In 1 & 2): Use the RGB cable to connect to a computer's VGA output.
• Video e kopaneng: Use the A/V cable to connect to devices with composite video output.
• S-Video: Connect to devices with S-Video output.
• Mohala ka: Hokela mehloli ea molumo kantle ka thapo ea stereo ea 3.5mm.
• RS232C: For control and automation systems.
• USB B Mini: For control and firmware updates.

Ensure all cables are securely connected before powering on the projector.

5. Litaelo tsa Ts'ebetso

5.1 Ho Bulela/Ho tima

• Ho bulela, tobetsa konopo Matla button on the control panel or remote control. The power indicator light will illuminate.
• Ho tima, tobetsa konopo Matla button again. Confirm shutdown if prompted. Allow the projector to cool down before unplugging.

5.2 Phetoho ea setšoantšo

• Tsepamisa maikutlo: Potoloha lesale la ho tsepamisa maikutlo lenseng ea projektha ho fihlela setšoantšo se hlakile ebile se hlakile.
• Lejoe la sehlooho: Sebelisa le Lejoe la sehlooho buttons on the control panel or remote to correct trapezoidal image distortion if the projector is not perfectly perpendicular to the screen.

5.3 Khetho ea Mohloli

Tobetsa ea Mohloli button on the control panel or remote control to cycle through available input sources (VGA1, VGA2, Video, S-Video).

5.4 Menu Navigation

Tobetsa ea Menu/Tswa button to access the on-screen display (OSD) menu. Use the arrow buttons to navigate and the Khetha or Kena button to confirm selections. Press Menu/Tswa again to close the menu.

Mokhoa oa 5.5 Eco

Activate Eco Mode to extend lamp life and reduce power consumption. This mode is suitable for environments with lower ambient light. The lamp life is approximately 6,000 hours in Eco Mode compared to 5,000 hours in normal mode.

5.6 3D Content Projection

The IN112 is 3D-ready. To project 3D content, you will need compatible 3D source material, a 3D-capable player, and active 3D glasses (sold separately). Refer to your 3D source device's manual for specific setup instructions.

6. Tlhokomelo

6.1 Lamp Ho nkela sebaka

Morero oa lamp e na le nako e lekanyelitsoeng ea bophelo. Ha lamp sesupo (Temp/Lamp) illuminates or the image brightness significantly decreases, the lamp may need replacement. The lamp door is conveniently located on the top of the projector for easy access, even when installed.

Tlhokomeliso: Ensure the projector is powered off and completely cooled before attempting lamp replacement. Refer to the detailed lamp replacement instructions in the full service manual for safety and proper procedure.

6.2 Ho hloekisa

The IN112 projector is designed without filters, eliminating the need for filter cleaning or replacement. Periodically wipe the exterior casing with a soft, dry cloth. For the lens, use a specialized lens cleaning cloth and solution to avoid scratches.

7. Ho rarolla mathata

8. Litlhaloso

9. Tiisetso le Tšehetso

9.1 Warranty ea Sehlahisoa

The InFocus IN112 projector is backed by a comprehensive warranty:

• Tiisetso e lekantsoeng ea selemo se le seng seporojekeng.
• Guarantee ea selemo sa 2 covering parts and labor.
• Waranti ea likhoeli tse 6 ho lamp.

Please retain your proof of purchase for warranty claims. For detailed terms and conditions, refer to the official InFocus warranty documentation or visit the InFocus websebaka.

9.2 Tšehetso ea Theknoloji

For technical assistance, troubleshooting, or service inquiries, please contact InFocus customer support. Contact information can typically be found on the InFocus official websaeteng kapa litokomaneng tse kenyellelitsoeng.

10. Related Product Information (IN130 Series)

Video e latelang e fana ka tlhaloso e felletsengview of features found in the InFocus IN130 Series projectors. While specific models may vary, many core functionalities and design principles are shared across InFocus projector lines, offering general insight into InFocus projector capabilities.